Samsung SCC-B2091P: инструкция

DIGITAL COLOR CAMERA

E

SCC-B2391(P)

D

SCC-B2091P

F

SCC-B2300

Sp

User’s Manual

I

Pl

R

Important Safety Instructions

CAUTION

This symbol indicates

RISK OF ELECTRIC

high voltage is present

E

SHOCK DO NOT OPEN

inside. It is dangerous to

make any kind of contact

with any inside part of this

product.

CAUTION: TO REDUCE THE

This symbol alerts you

RISK OF ELECTRIC SHOCK,

that important literature

DO NOT REMOVE REAR

concerning operation and

COVER. NO USER

maintenance has been

SERVICEABLE PARTS INSIDE.

included with this product.

REFER TO QUALIFIED

SERVICE PERSONNEL.

To prevent damage which may result in fire or electric shock hazard,

do not expose this appliance to rain or moisture.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions.

1) This device may not cause harmful interference, and

2) This device must accept any interference that may cause undesired

operation.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

2

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

E

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, or other apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being from being walked on or

pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a used,

caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-

over.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or been dropped.

3

Contents

Chapter 1 Introduction ........................................................ 5

E

Chapter 2 Special Features ............................................. 6

Chapter 3 Installation ........................................................... 7

Checking the contents of the package .............. 7

Precautions in Installation and Use ................... 8

Connecting Auto Iris Lens Connector ................ 9

Lens Fixing

........................................................... 10

Setting Lens Selection Switch

.................... 11

Back Focus Adjustment

................................ 11

Connecting Cables and Checking Operation ....... 13

Chapter 4 Part Names and Functions ............................... 15

Product Specification ........................................ 20

4

Chapter 1 Introduction

DAYNIGHT camera is a low brightness camera, which improves the sensitivity

by operating with a color mode at the over of regular brightness and operated

with a B/W mode by canceling the IR Cut function at the below of regular

E

brightness. Also, it can be used linked with the separated infrared ray emission

device. SCC-B2391(P)/B2091P has a high resolution with the 540 TV Lines of

horizontal resolution through the digital signal processing and OLPF.

[DAYNIGHT]

It is a function of a color camera to delete the fiter with

the IR Cut function in an illumination below the standard

value so that it has a better sensitivity.

❉

In the mechanical fluorescent light environment, if you attach MANUAL IRIS

LENS and turn the ELC switch among FUNCTION switches on, color may be

rolled.

In this case, supply AC power before you turn L/L switch among FUNCTION

switches on. (NTSC:60HZ , PAL:50HZ)

COLOR ROLLING is the problem that color on the

monitor screen changes non-periodically.

This happens when White Balance is not fixed,

because a mechanical fluorescent light flickers

when it’s cycle is the same to the cycle of the power

frequency.

5

Chapter 2 Special Features

High Sensitivity

It has an up-to-date 1/3" Super-HAD IT CCD for an image of high sensitivity.

E

Resolution

It realizes high resolution resulting from full digital image processing

supported by a state-of-art digital signal technology.

Superior Back Light Adjustment Function

In case the object has a bright illumination or sunlight behind it, this camera

adjusts the image shaded by the back light for clear photographs.

Digital Power Supply Synchronization Method

The Full Digital Method Line Lock is realized in this camera, which adjusts

the vertical camera synchronization directly to improve controllability and

reliability of the camera.

6

Chapter 3 Installation

This chapter describes what should be checked before installation, how to

set the installation environment, and what should be done during installation.

Then, it describes how to install the camera and connect the cable in actual

circumstances.

E

Checking the contents of the package

Be sure to check if the following items are included in the package.

Camera

Camera

Holder(Mount)

User's Manual

C Mount Adapter

Auto Iris

Lens Connector

7

Precautions in Installation and Use

E

① Do not attempt to disassemble the camera yourself.

➁ Be cautious in handling the camera. Avoid striking or shaking the

camera. Be cautious to avoid damage on the camera caused by improper

storage or operation.

➂ Do not expose this camera to rain or moisture. Do not operate this

camera on a wet place.

➃ Do not use strong or abrasive detergents when cleaning the camera

body. Use a dry cloth to clean the camera.

⑤ Keep the camera at a cool place away from the direct sunlight. Leaving it

under the direct sunlight may result in the malfunction of the unit.

8

Connecting Auto Iris Lens Connector

Prepare the following Auto Iris Lens Connector supplied with the camera.

E

Rb

Pin3

Pin1

Pin4

Pin2

Connect the cable of the control cable, whose covering is stripped, to the

Auto Iris Lens Connector as shown below.

Pin No. DC Control Type VIDEO Control Type

1 Damp(-) Power (+12V)

2 Damp(+) N/A

3 Drive(+) VIDEO Signal

4 Drive(-) GROUND

9

Rear View

AC24V/DC12V Camera (SCC-B2391(P)/B2300)

E

⑤

⑨

➁

➅

➂ ➃

⑦

①

⑧

AC230V Camera (SCC-B2091P)

⑤

①

➁

➅

➂ ➃

⑦

⑨

⑧

16

① Power connection port

AC24V/DC12V Camera : It is a port connected to the power adaptor cable.

AC230V Camera : It is Power cord.

E

➁ POWER LED

If the power of a camera is supplied normally, the LED is ON.

➂➃INC and DEC Switch

Both switches increase or decrease the profit of RED and BLUE to fix a color

temperature as you wish while AWB among the FUNCTION switches is

off(USER) and control the vertical synchronous phase while both AWB and

L/L are on.

⑤ FUNCTION Switch

1. L/L 2. ELC

3. FL 4. AWB

SW1 SW2 SW3 SW4

17

1) SW1(L/L) :

Set to OFF, the camera activates the internal synchronization mode and set to ON, the power

synchronization mode. If you connect multi cameras to the sequential switcher to enter the

automatic conversion mode, the screen will bounce every screen while the camera stays in

E

INT(internal synchronization). Such bouncing phenomena may be cleared and screen conversion

becomes smooth by setting the L/L switch to ON and using the INT/DEC switch to control the

vertical synchronous phase.

❉

If you want to control the vertical synchronous phase with the INT/DEC switch when L/L is set

to ON, you shall set SW4 to AWB ON.

❉

In case of DC12V, INT(internal synchronizer) will be fixed without regard to ON/OFF of L/L.

❉

If you want to use the camera with PDP/LCD, please set the L/L switch OFF.

2) SW2(ELC) :

Use this switch with the Manual Iris Lens. While this switch is ON, the speed of the electronic

shutter varies with the brightness of the subject from 1/60(50) to 1/100,000 sec for automatically

controlling the brightness of the screen. However, with the Auto Iris Lens (DC or Video Control),

be sure to switch OFF.

Color Rolling may occur in this mode. In that case, input AC power source to the camera and

select SW1 "ON".

(NTSC : 60HZ, PAL : 50HZ)

3) SW3(FL):

This is to prevent flicker on the screen when NTSC system is used in 50HZ power supply region

and PAL system is used in 60HZ power supply region. That is to prevent shaking on the

screen resulted from the discordance of the vertical sync frequency and the flicker frequency of

the illumination. While this switch is ON, the electronic shutter is fixed to 1/100sec (NTSC) or

1/120 sec (PAL).

4) SW4(AWB):

When setting up ON, the color of screen is adjusted automatically in accordance with the change

of lighting color temperature by the change of outer environment. (ATW) If the lighting condition is

steady, OFF setting is available. The camera memorizes the lighting color temperature at the

time when the switch setting is changed from ON to OFF, and the camera color is adjusted to the

memorized color temperature. (AWC) If the lighting color temperature is changed and you want

to make the camera be memorized/operated with the changed color temperature, re-operate the

switch On/Off operation. However, be aware that an error may occur under the following

conditions.

First, a case that the subject is big, single color of the high chroma, and in the center of

the screen or a case with almost no white color on the screen.

Second, a case with a specific illumination such as a natrium lamp

18

➅

DC IRIS Level Controller

When the ALC lens selection switch is set to DC, use the same control bar as the

driver to control the IRIS level.

E

⑦

Video Output Port

This port shall be connected to the monitor video input port or equivalent. You

may output camera video signals through this port.

⑧

DAYNIGHT Selection Switch

If you set this switch to AUTO, the DAYNIGHT function will be automatically

activated according to the illumination. Under poor illumination, IR Filter will be

automatically eliminated in the black and white mode(BW Mode) to raise the

sensitivity but under good illumination, IR Filter will be automatically inserted in

the color mode(COLOR Mode).

IR Filter responds to the preset Duration Time (Delivery Condition:10 seconds).

When you convert DAYNIGHT in the AUTO mode, you shall set Duration Time

as follows. (Please turn off the L/L switch and the AWB switch to begin with).

Whenever you convert the DAYNIGHT selection switch from EXT to AUTO while

you hold on to the INC/DEC switch, DURATION TIME becomes 10s, 30s, 60s,

90s, 120s, and 150s in sequence. Upon setup, you shall cancel pressing the

INC/DEC switch to save the setup condition in the camera. Upon saving, the

DAYNIGHT mode will be automatically converted depending on DURATION

TIME even in the event of POWER On/Off.

For resetting, please repeat the above procedure. (Upon resetting, you may r

eturn both L/L and AWB to the previous condition.)

If you set this switch to EXT, COLOR/BW Mode varies depending on the external

signal input to the DAYNIGHT external signal input port(

⑨

).

⑨

DAYNIGHT External Signal Input Port

When the DAYNIGHT selection switch(

⑧

) is set to EXT, COLOR/BW Mode

varies depending on the input signal to this port.

The input terminal shall be DC5V pull-up input and over 0.2mA.

OFF : Open contact

ON : Closed contact

19

Product Specification

SCC-B2391P/2091P

ITEM

Contents

E

Product Type CCTV Camera

Broadcasting System PAL STANDARD SYSTEM

CCD 1/3 Super-HAD CCD

Effective Pixels 752(H) x 582(V)

Scanning Type 625 Line, 2:1 Interlace

INTERNAL : 15,625Hz(H)

50 Hz(V)

Frequency

LINE LOCK :

15,625Hz(H)

50 Hz(V)

INTERNAL

Sync Type

LINE LOCK(When AC Power source is used)

Resolution(H) 540(Color)/570(B/W) TV Lines

S/N Ratio About 50dB

Minimum Illumination

0.3 Lux(Color) / 0.06 Lux(B/W)

of Object

DAYNIGHT AUTO / EXT

20

ITEM

Contents

E

ALC

DC IRIS LENS

ALC/ELC VIDEO LENS

ELC

Electronic Shutter Iris Function (Max. 1/100 Ksec)

Color Temperature

AWB/MANUAL

BLC

ON

AGC ON

Video Output

COMPOSITE VIDEO OUT

1V p_p 75Ω/BNC

Power Source

B2391P : AC24V±10%(50Hz±0.3Hz), DC12V+10%~-5%

B2091P : AC220V~AC240V(50Hz±0.3Hz)

B2391P : About 3W

Power Consumption

B2091P : About 4W

Operating Temp

-10

°C

~+50

°C

Operating Humidity

~90%

Size 68(W)x55(H)x128.5(D)mm(included BNC)

B2391P :

450g

Weight

B2091P : 550g

21

Product Specification

SCC-B2391/B2300

ITEM

Contents

E

Product Type CCTV Camera

Broadcasting System NTSC STANDARD SYSTEM

CCD 1/3 Super-HAD CCD

Effective Pixels

B2391 :

768(H) x 494(V)

B2300 :

510(H) x 492(V)

Scanning Type 525 Line, 2:1 Interlace

INTERNAL : 15,734Hz(H)

59.94 Hz(V)

Frequency

LINE LOCK : 15,750Hz(H)

60 Hz(V)

INTERNAL

Sync Type

LINE LOCK(When AC Power source is used)

Resolution(H) B2391 : 540(Color)/570(B/W) TV Lines

B2300 : 400(Color)/420(B/W) TV Lines

S/N Ratio About 50dB(AGC OFF)

B2391 : 0.3 (Color) / 0.06 (B/W)Lux

Minimum Illumination

of Object

B2300 : 0.2 (Color) / 0.03 (B/W)Lux

DAYNIGHT AUTO / EXT

22

ITEM

Contents

E

ALC

DC IRIS LENS

ALC/ELC VIDEO LENS

ELC

Electronic Shutter Iris Function (Max. 1/100 Ksec)

Color Temperature

AWB/MANUAL

BLC

ON

AGC ON

Video Output

COMPOSITE VIDEO OUT

1V p_p 75Ω/BNC

Power Source

AC24V

±

10%(60Hz

±

0.3Hz), DC12V

+

10%~-5%

Power Consumption About 3Watts

Operating Temp

-10

°C

~+50

°C

Operating Humidity

~90%

Size 68(W)x55(H)x128.5(D)mm(included BNC)

Weight

450g

23

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other

household wastes at the end of its working life. To prevent possible harm to the environment or human

health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local

government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

Part No.:AB68-00511B