Samsung SCC-C4207P: инструкция

320X POWER ZOOM WDR CAMERA

SCC-C4207(P)/C4307(P)

Owner’s Instructions

E

êÛÍÓ‚Ó‰ÒÚ‚Ó ÔÓθÁÓ‚‡ÚÂÎfl

RU

Instrukcja obs∏ugi

PL

✽ Be sure to read the "Safety Precautions" in this manual

CODE : AB68-00545A(00)

to ensure correct use and operation of this product.

Printed in China

Important Safety Instructions

Safety Precautions

1. Read these instructions.

The purpose of safety precautions is to prevent accidental

2. Keep these instructions.

injury or property damage. Always observe all safety

3. Heed all warnings.

precautions.

4. Follow all instructions.

❖ The precautions are divided into "Warnings" and

5. Do not use this apparatus near water.

"Cautions" as distinguished below:

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in

accordance with the manufacturer's instructions.

E

8. Do not install near any heat sources such as radiators,

heat registers, or other apparatus (including amplifiers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or

Warning

Caution

grounding- type plug. A polarized plug has two blades with

Ignoring this precaution

Ignoring this precaution

one wider than the other.

may result in death or

may result in injury or

A grounding type plug has two blades and a third

serious injury.

damage to property.

grounding prong.

The wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete

outlet.

10. Protect the power cord from being walked on or pinched

Warnings

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

1. Be sure to use only the standard adapter which is

11. Only use attachments/accessories specified by the

specified in the specification sheet.

manufacturer.

Using any other adapter could cause fire, electrical

12. Use only with cart, stand, tripod, bracket, or table specified

shock, or damage to the product.

by the manufacturer, or sold with the apparatus.

2. Check the external connection terminals first before

connecting the power source and signal wires.

Connect the alarm signal wires to the alarm terminals.

Connect the DC12V power adapter to the SCC-

C4207(P) power input, making

sure that the currect polarity is observed.

Connect the DC12V or AC24V power adapter to the

13. Unplug this apparatus. When a cart is used, use caution

SCC-C4307(P) power input.

when moving the cart/apparatus combination to avoid

injury from tip-over.

14. Refer all servicing to qualified service personnel. Servicing

3. Do not connect multiple cameras to a single adapter.

is required when the apparatus has been damaged in any

(Exceeding the capacity may cause abnormal heat

way, such as power-supply cord or plug is damaged, liquid

generation or fire.)

has been spilled or objects have fallen into the apparatus

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

1

2

4. Securely plug the power cord into the power receptacle.

Cautions

(A loose connection may result in fire.)

1. Do not drop objects on the product or apply strong shock

5. When mounting the camera on a wall or ceiling, fasten it

to it. Keep away from a location subject to excessive

safely and securely. (A falling camera may cause

vibration or magnetic interference.

personal injury.)

2. Do not install in a location subject to high temperature,

6. Do not place conductive objects (e.g., screwdrivers,

low temperature, or high humidity. (Doing so may cause

coins, and metal things) or containers filled with water on

fire or electrical shock.)

top of the camera.

E

(Serious injury may result from fire, electrical shock, or

3. Avoid a location which is exposed to direct sunlight, or

falling objects.)

near heat sources such as heaters or radiators.

(Neglecting to do so may result in a risk of fire.)

7. Do not install the unit in humid, dusty, or sooty locations.

(Doing so may cause fire or electrical shock.)

4. If you want to relocate the already installed product, be

sure to turn off the power before moving or reinstalling it.

8. If any unusual smells or smoke come from the unit, stop

using the product. In such case, immediately disconnect

5. Install in a well-ventilated location.

the power source and contact the service center.

6. Remove the power plug from the outlet when there is a

(Continued use in such a condition may cause fire or

lightning storm. (Neglecting to do so may cause fire or

electrical shock.)

damage to the product.)

9. If this product fails to operate normally, contact the store

of purchase or your nearest service center. Never

disassemble or modify this product in any way.

(Problems caused by unauthorized user disassembly or

repairs are not covered by your warranty.)

10. When cleaning, do not spray water directly onto parts of

the product. (Doing so may cause fire or electrical

shock.) Gently wipe the surface with a dry cloth. Never

use detergents or chemical cleaners on the product, as

this may result in discoloration of surface or cause

damage to the finish.

3

4

FCC Statement

Contents

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

1. Overview.............................................................7

(2)

This device must accept any interference received,

including interference that may cause undesired operation.

2. Part Names and Functions ...............................8

Note:

3. Installation........................................................11

This equipment has been tested and found to comply with

Checking the Package Contents .......................11

E

the limits for Class B digital devices, pursuant to Part 15 of

Preparing the Cables ........................................12

the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a

Connecting the Cables ......................................13

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

4. Navigating the Setup Menu.............................15

used in accordance with the instructions, may cause harmful

Structure of the Setup Menu .............................15

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

- CAMERA ID.....................................................16

installation. If this equipment does cause harmful

- IRIS..................................................................16

interference to radio or television reception, which can be

- SHUTTER........................................................19

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

- FLICKERLESS ................................................20

of the following measures:

- AGC/MOTION ................................................21

- WHITE BAL .....................................................22

- Reorient or relocate the receiving antenna

- Increase the separation between the equipment and

- FOCUS MODE ................................................23

receiver

- MOTION DET ..................................................23

- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected

- COLOR / BW ...................................................25

- Consult the dealer or an experienced radio/TV technician

- PRIVACY.........................................................27

for help Use of shielded cable is required to comply with

- SPECIAL .........................................................28

Class B limits in Subpart B of Part 15 of the FCC rules.

- DISPLAY ZOOM..............................................31

Do not make any changes or modifications to the

- PRESET ..........................................................31

equipment unless otherwise specified in the manual.

- EXIT.................................................................32

If such changes or modifications should be made, you

could be required to stop operation of the equipment.

5. Product Specification .....................................33

5

6

1

Overview

2

Part Names and Functions

This is a state-of-art WDR zoom camera which employed the

x32 zoom lens and digital zoom IC to monitor up to 320 times

as large as an original image.

SCC-C4207(P)/C4307(P) has the following functions.

●

WDR for distinct photographing of both bright and dark

E

parts of an image.

●

DAY/NIGHT to raise the sensitivity by automatic

conversion into the White & Black mode at night or in poor

illumination environment.

●

Low - Light Surveillance function that enables image

capture even under extremely low light conditions.

●

White Balance function that provides accurate color

rendition under any light conditions.

●

BLC function that enables effective back light

compensation even under a spotlight or a very bright

incident light.

●

Auto Focus function that automatically tracks and focuses

on the moving subject.

●

Privacy Zone function to hide a special area for privacy

protection.

●

RS485/ Wired remote control function.

Broadcast System

●

SCC-C4207/4307 : NTSC System

●

SCC-C4207P/4307P : PAL System

Power System/Power Consumption

●

SCC-C4207(P): DC 12V/5.5W

●

SCC-C4307(P): AC 24V, DC 12V/6W

7

8

SET-UP button

Instead of “POWER”, “DC IN”

is writtern in SCC-C4207(P).

Instead of “POWER”, “PWR

IN” and instead of “GND”,

“DC12&AC24V” is writtern in

SCC-C4307(P).

SET-UP button

The function of the SET-UP button varies depending on

whether you are currently in Normal Operation mode (i.e.,

the Setup Menu is not displayed) or Setup Menu mode.

✔

In Normal Operation Mode

- UP/ DOWN buttons : Use as the ZOOM Tele button

and the ZOOM Wide button respectively.

- LEFT/ RIGHT buttons : Use as the FOCUS Near

button and the FOCUS Far button respectively.

- SET- UP button: Use to enter the Setup Menu.

Hold the SET- UP button for longer than 3 seconds to

enter the Setup Menu.

Press the [SET UP] switch shortly (within 1 sec.) to

start the AF function.

✔

In Setup Menu Mode

DAY/NIGHT External Signal Input & Alarm Signal

Output

- UP/ DOWN buttons: Use to move the cursor up or down.

This is a function to receive the external DAY/NIGHT

- LEFT/ RIGHT buttons: Use to move the cursor left or

signal from the sensor(option) and convert the signal into

right, or to sequentially view the values that can be

BW. An alarm signal is output from this terminal when the

assigned to a parameter.

MOTION DET mode is activated or BW mode is activated.

- ENTER button: Use to select a Sub Menu item, and to

DAY/NIGHT IN

accept the current value.

1

GND

ZOOM/ FOCUS REMOTE terminals

E

2

This port is used for ZOOM/FOCUS, MENU CONTROL,

ALARM OUT

HOME RETURN, and AF by using an external controller.

Depending on the input condition, 4 modes, A, B, C, and

Connect an external sensor to the DAY/NIGHT terminal

D are available. (SPECIAL - CTRL TYPE)

as shown in

➀

then connect any external device such as

(Operation Voltage Range : +3V~+13V, -3V~-13V)

a buzzer or lamp to the ALARM terminal as shown in

➁

.

1)

When the voltage is supplied to either ZOOM or FOCUS port,

The ALARM output terminal is an open collector with the

Function

TELE(Up)

WIDE(Down)

NEAR(Left)

FAR(Right)

following capacity: DC 16V and 100mA.

❖ 1

Code

ZOOM Port

FOCUS Port

A

-6V

+6V

-6V

+6V

OFF : Open contact

B

-6V

+6V

+6V

-6V

ON : Below 100mA

C

+6V

-6V

-6V

+6V

D

+6V

-6V

+6V

-6V

The DAY/NIGHT input terminal has the input of DC 5V

pull-up and over 0.2mA.

❖ 1: During MENU OFF, controls ZOOM/FOCUS and

during MENU ON, changes the direction, Up, Down,

OFF : Open contact

Left, and Right.

ON : Closed contact

2) When the voltage is supplied to both ports

VIDEO OUT terminal

Function

ENTER/AF ❖ 2

HOME RETURN ❖ 3

Code

Connect the monitor's VIDEO IN. The video signal from

ZOOM Port

FOCUS Port

ZOOM Port

FOCUS Port

-6V

+6V

+6V

the camera is transmitted to the monitor via this terminal.

A

-6V

B

-6V

+6V

+6V

-6V

RS485 terminal

C

+6V

-6V

-6V

+6V

+6V

+6V

-6V

RS485 remote control terminal.

D

-6V

Power LED

❖ 2: For short voltage supply during MENU OFF,

Lights when power is on.

executes AF and for more than 2 second

POWER IN terminal

❖ 3: For more than 2 second long voltage supply, moves

Plug in the power adapter here.

to the PRESET 0(HOME) position.

109

3

Installation

Preparing the Cables

To install and use the camera, first prepare the following

Before Installation

cables.

The requirements for the power adapter, which connects to

the camera's POWER IN terminal, are as follows:

Checking the Package Contents

●

SCC-C4207(P) : DC12V 600mA

Make sure that the following accessories are included in

●

SCC-C4307(P) : AC24V 300mA

E

the package.

DC12V 600mA

SCC-C4207(P)/4307(P)

User's Guide

Video Cable

Use a BNC cable, such as the one shown below, to connect

the camera's VIDEO OUT to the monitor.

Mount Adapter

Screw (2)

Terminal Block

11

12

Connecting the Cables

1. Connect one end of the BNC cable to the VIDEO OUT.

4. Determine the type of power supply and set the POWER

SELECTION switch accordingly. Next, plug the power

2. Connect the other end of the BNC cable to the VIDEO IN

adapter into a wall outlet.

of the monitor.

The requirements for the power adapter for each model are

as follows:

●

SCC-C4207(P) : DC12V 600mA

E

●

SCC-C4307(P) : AC24V 300mA

DC12V 600mA

Video terminals on the back

of the monitor

5. If the camera operates normally, the following screen will

be displayed for 5 seconds and then disappears.

BNC cable

SAMSUNG PROTOCOL

ADDRESS 0

TYPE

RS-485, HALF

BAUD RATE 9600

LENS OK

EEP VER 1.000

3.

Plug in the power adapter. Use a "minus" screwdriver to

ROM VER 1.000

connect one part of the power adapter, which consists of

two lines, to the POWER terminal of the camera as follows :

❖

ROM VER and EEP VER may change without notice.

POWER SELECTION switch

underneath the power adapte

6. The requirements for RS485 control is as follows :

●

Signaling Speed: 9600 bps

●

Data Bit : 8 bits

●

Stop Bit : 1 bit

●

Parity Bit : none

POWER SELECTION

switch underneath the

power adapte

13

14

Navigating the Setup Menu

❙

CAMERA ID

4

In the CAMERA ID menu, you may designate the CAMERA

ID to be displayed in the monitor connected to a camera. Set

In this chapter, we will take a look at the menu system of the

the CAMERA ID menu to ON... and press [ENTER] and the

SCC-C4207(P),C4307(P). First, we will take a look at the

CAMERA ID setup submenu will appear. The CAMERA ID

structure of the Setup Menu and then describe the functions

may be created by up to 20 digits by using alphabets,

of each menu item in the menu.

numbers, and some special texts served by the submenu

screen. You may locate the designated CAMERA ID on your

Structure of the Setup Menu

own by using the LOCATION... submenu.

E

CAMERA ID ON...

(CAMERA ID)

CAMERA ID

OFF/ON...

IRIS ALC...

SHUTTER OFF

ABCDEFGH I JKL

AGC LOW

MNOPQR ST U VWX

IRIS

ALC.../WDR.../MANU...

WHITE BAL ATW1

YZ0 123 456 789

SHUTTER

OFF/1/100 ~ 1/10K/AUTO X2...~X160...

FOCUS MODE AF

.; ! -+

*

() /

Press the

MOTION DET OFF

ENTER

SP

❿❿☎☎☎☎➛➛

SP

AGC/MOTION

OFF/LOW/HIGH(AGC)

COLOR/BW AUTO...

PRIVACY OFF

button.

LOCATION...

SPECIAL ...

S.SLOW/SLOW/NORMAL/

RET

PRESET ...

......................

FAST/F.FAST(MOTION)

EXIT QUIT

WHITE BAL

ATW1/ATW2/AWC/MANU...

❙

IRIS

FOCUS MODE

AF/MF/ONEAF

✔

ALC

MOTION DET

OFF/ON...

Select ALC... from the IRIS menu and press [ENTER]

COLOR/BW

COLOR.../BW.../AUTO.../EXT...

and the BLC(Back Light Compensation) setup submenu

PRIVACY

OFF/ON...

will appear. If you use a general camera to photograph a

subject under backlight or bright illumination, the subject

SPECIAL

...

will be shown dark on the monitor due to the backlight.

POSI/NEGA +/-

BLC(Back Light Compensation) is used to prevent such a

backlight problem to secure distinct images under bright

DIS OFF

illumination. Using the [Left, Right] keys, you can set up

REVERSE OFF

BOTTOM…, TOP…, LEFT…, RIGHT…, CENTER… 5

DETAIL ( 1)-I-

preset areas and the USER…function that can directly

set the areas. For example, for the items in the BLC

Y-LEVEL ( 0)|--------

menu, you can confirm the preset BOTTOM area by

C-LEVEL ( 0)|--------

pressing [ENTER] key in the BOTTOM… status.

OTHER SET ...

CAMERA ID OFF

(IRIS/ALC)

IRIS ALC...

LANGUAGE/CTRL TYPE/

SHUTTER OFF

RS-485/SYSTEM INFO/

AGC LOW

WHITE BAL ATW

V-SYNC(❖)

FOCUS MODE AF

MOTION DET OFF

Press the

RET

COLOR/BW AUTO...

ENTER

PRIVACY ...

button.

BLC OFF

PRESET

...

SPECIAL ...

LEVEL (00) ----I----

PRESET ...

RET

EXIT

EXIT QUIT

15

16

❖ V-SYNC menu is only available in SCC-C4307.

- C-LEVEL: It is used to set the levels for the Burst signal

(OTHER SET)

(RS-485)

and the entire colour signal of the video signal.

LANGUAGE ENGLISH

CTRL TYPE A

- OTHER SET

ZOOM SPEED 4

In OTHER SET menu, you can adjust LANGUAGE, CTRL

D-ZOOM OFF

Press the

RS-485 ...

ENTER

TYPE, ZOOM SPEED, D-ZOON, RS-485, SYSTEM

SYSTEM INFO ...

button.

PROTOCOL SAMSUNG

V-STNC INT

INFO..., and V-SYNC function, DISPLAY ZOOM etc. When

BAUD RATE 9600

ADDRESS 0

you press [ENTER] key from OTHER SET menu, the

RET

RET

OTHER SET additional menu screen appear.

- SYSTEM INFO : You can confirm settings related to the

(SPECIAL)

E

(OTHER SET)

RS-485 communication, product serial number, and the

POSI/NEGA +

LANGUAGE ENGLISH

software version.

DIS OFF

CTRL TYPE A

REVERSE OFF

ZOOM SPEED 4

D-ZOOM OFF

(OTHER SET)

DETAIL (0)--I-

(SYSTEM INFO)

RS-485 ...

Y-LEVEL (0)I--------

SYSTEM INFO ...

LANGUAGE ENGLISH

C-LEVEL (0)I--------

ROM VER 1.000

V-SYNC INT

CTRL TYPE A

OTHER SET ...

DISPLAY ZOOM OFF

EEP VER 1.000

ZOOM SPEED 4

PROTOCOL SAMSUNG

Press the

D-ZOOM OFF

RET

RET

ADDRESS 0

RS-485 ...

ENTER

TYPE RS-485, HALF

SYSTEM INFO ...

button.

BAUD RATE 9600

V-STNC INT

SERIAL NO 000000000000000

❖

V-SYNC menu is only available in SCC-C4307.

RET

RET

- LANGUAGE : Selects English/Russian/Polish OSD menu.

- V-SYNC : INT shall be selected to use internal

- CTRL TYPE : By inputting the wire remote port, you may

synchronization. LINE... is used to synchronize several

set up the mode, A, B, C, or D.

camera phases for the multi camera operation by using an

external signal(AC signal). As there may be a slight deviation

Code

Tele

Wide

Far

Near

between sets, adjusts PHASE to overcome this handicap.

A

-6V

+6V

+6V

-6V

B

-6V

+6V

-6V

+6V

When you use AC power source, V-SYNC is available.

-6V

-6V

C

+6V

+6V

Select LINE... and press [ENTER] and the PHASE control

D

+6V

-6V

-6V

+6V

submenu will appear. The PHASE control ranges from -106H

to +106H as for NTSC and from -138H to +138H as for PAL.

- ZOOM SPEED : Use [Left, Right] key in the ZOOM SPEED

menu to set the speed as follows.

❖

When a DC power is supplied, V-SYNC menu will be displayed

as --- and you cannot make any settings.

- ZOOM SPEED 1 : About 17Sec. from X 1 to X 32(Slowest)

- ZOOM SPEED 2 : About 10Sec. from X 1 to X 32(Slow)

(SPECIAL)

CTRL TYPE A

(LINE LOCK)

- ZOOM SPEED 3 : About 6Sec. from X 1 to X 32(Fast)

POSI/NEGA +

- ZOOM SPEED 4 : About 3Sec. from X 1 to X 32(Fastest)

ZOOM SPEED 1

DIS OFF

D-ZOOM OFF

- D-ZOOM : Sets up the Digital Zoom magnification ratio up

Press the

REVERSE OFF

ENTER

to x10.

RS-485 ...

V-SYNC LINE...

button.

- RS-485 : Sets up RS-485 Communication Protocol,

LANGUAGE ENGLISH

DETAIL (0)--I-

PHASE (000)----I----

Address, and Baud Rate.

RET

RET

29

30

❙

DISPLAY ZOOM

❖ HOME RETURN automatically returns to the HOME

position should there is no key input for a certain time.

In DISPLAY ZOOM, you can display the ZOOM scale on the screen.

The HOME position is set to PRESET 0 if it is saved or

Off if not.

(OTHER SET)

10X

LANGUAGE ENGLISH

CTRL TYPE A

HOME RETURN Time Setup

ZOOM SPEED 4

DIGITAL ZOOM X10

Press the

RS-485 ...

➞

OFF ➞ 1MIN ➞ 2MIN ➞ 3~60MIN ➞ 2 HOUR ➞ 3~12 HOUR

ENTER

SYSTEM INFO ...

button.

E

V-SYNC LINE...

DISPLAY ZOOM ON

EXIT

❙

EXIT

The EXIT menu is used to terminate the CAMERA SETUP

❈ If no change on the ZOOM scale is made for 3 seconds, the

menu.

information window will disappear.

✔

QUIT : Select to ignore any changes you have made and

restore the previously saved settings.

❙

PRESET

✔

SAVE : Select to save the settings that have been

changed so far.

Select the PRESET menu and press [ENTER] and the

PRESET MAP submenu screen will appear.

✔

PRESET : Ignores any change and returns to the default of

the CAMERA menu as set for the product delivery.

(PRESET MAP)

PRESET NO. 0

0 H 1 2 3 4

CAMERA ID OFF

56789

POSITION SET ...

IRIS ALC...

10 11 12 13 14

PRESET ID OFF

SHUTTER OFF

15 16 17 18 19

Press the

AGC LOW

20 21 22 23 24

WHITE BAL ATW1

ENTER

25 26 27 28 29

FOCUS MODE AF

30 31 RET

button.

MOTION DET OFF

HOME RETURN OFF

COLOR/BW COLOR

EXIT QUIT

PRIVACY OFF

EXIT QUIT

SPECIAL ...

PRESET ...

EXIT QUIT

Select the PRESET number and press [ENTER] and the

above screen will appear.

✔

POSITION SET :

Memorizes the position of ZOOM or

FOCUS.

✔

PRESET ID :

Designates the ID on the basis of the

PRESET position as the CAMERA ID.

31

32

5

Product Specification

SCC-C4207/C4307

SCC-C4207P/C4307P

Item Description

Remark

Item Description

Remark

Product Type

Zoom Lens Built-in WDR Color Camera(NTSC TYPE)

Product Type

Zoom Lens Built-in WDR Color Camera(PAL TYPE)

- SCC-C4207 : DC 12V±10%

- SCC-C4207P : DC 12V

±

10%

Power Supply

Power Supply

- SCC-C4307

: DC 12V±10%

- SCC-C4307P

: DC 12V±10%

Voltage

Voltage

AC 24V±10% (60Hz±0.3Hz)

AC 24V±10% (50Hz±0.3Hz)

E

- SCC-C4207 : 5.5W

- SCC-C4207P : 5.5W

Power Consumption

Power Consumption

- SCC-C4307 : 6W

- SCC-C4307P : 6W

Broadcast System

- NTSC Standard Color System

Broadcast System

- PAL Standard Color System

Imaging Device

- 1/4 inch WDR compatible Exview HAD CCD

Imaging Device

- 1/4 inch WDR compatible Exview HAD CCD

Effective Pixe

- 768(H) x 494(V)

Effective Pixe

- 752(H) x 582(V)

Scanning Method

- 525 Line, 2:1 Interlace

Scanning Method

- 625 Line, 2:1 Interlace

- SCC-C4207

- SCC-C4207P

Horizontal : 15,734 Hz (INT)

Horizontal : 15,625 Hz (INT)

Vertical : 59.94 Hz (INT)

Vertical : 50 Hz (INT)

Line Frequency

Line Frequency

- SCC-C4307

- SCC-C4307P

Horizontal : 15,734 Hz(INT), 15,750 Hz(L/L)

Horizontal : 15,625 Hz(INT), 15,625 Hz(L/L)

Vertical : 59.94 Hz(INT), 60 Hz(L/L)

Vertical : 50 Hz(INT), 50 Hz(L/L)

Synchronization

-SCC-C4207 : Internal Only

Synchronization

-SCC-C4207P : Internal Only

Method

-SCC-C4307 : Internal/Line-Lock

Method

-SCC-C4307P : Internal/Line-Lock

Resolution

- 480 TV Lines

Resolution

- 480 TV Lines

S/N Ratio

- 50dB(AGC OFF)

S/N Ratio

- 50dB(AGC OFF)

Minimum Scene

- Color :

0.18 Lux (SENS UP X4) 0.005 Lux (SENS UP X160)

Minimum Scene

- Color :

0.18 Lux (SENS UP X4) 0.005 Lux (SENS UP X160)

Illumination

-

B/W :

0.018 Lux (SENS UP X4) 0.0005 Lux (SENS UP X160)

Illumination

-

B/W :

0.018 Lux (SENS UP X4) 0.0005 Lux (SENS UP X160)

Dynamic Range

- Max 128

Dynamic Range

- Max 128

- ATW1/ATW2/AWC/Manual MODE

- ATW1/ATW2/AWC/Manual MODE

Color Temp.

Color Temp.

(3200K, 5600K, R/B Gain Adjustment)

(3200K, 5600K, R/B Gain Adjustment)

Signal Output

- Composite Video Out : 1.0 Vp-p 75ohms/BNC

Signal Output

- Composite Video Out : 1.0 Vp-p 75ohms/BNC

-

32x Zoom Lens in a single unit

-

32x Zoom Lens in a single unit

- Focal length : 3.55 to 113 mm

- Focal length : 3.55 to 113 mm

Lens

Lens

- Aperture : F1.69(Wide), F4.17(Tele)

- Aperture : F1.69(Wide), F4.17(Tele)

- MOD(Minimum Object Distance) : 2.5m

- MOD(Minimum Object Distance) : 2.5m

- Tele/Wide(ZOOM), Near/Far(FOCUS),

- Tele/Wide(ZOOM), Near/Far(FOCUS),

Remote Control

Remote Control

Iris Open/Close

Iris Open/Close

Alarm

- Alarm Output: 1 Out (Motion Detection)

Alarm

- Alarm Output: 1 Out (Motion Detection)

Operating Temp.

-10°C ~ +50°C

Operating Temp.

-10°C ~ +50°C

Operating Humidity

- ~90%

Operating Humidity

- ~90%

- SCC-C4207 : 59.5 X 60.5 X 115.7 mm

- SCC-C4207 : 59.5 X 60.5 X 115.7 mm

Dimensions

Dimensions

- SCC-C4307 : 59.5 X 60.5 X 149.9 mm

- SCC-C4307 : 59.5 X 60.5 X 149.9 mm

- SCC-C4207 : 390g

- SCC-C4207 : 390g

Weight

Weight

- SCC-C4307 : 515g

- SCC-C4307 : 515g

Lens Lifetime

- About 1 year (when using the Full-AF mode)

Lens Lifetime

- About 1 year (when using the Full-AF mode)

33

34

Memo

Correct Disposal of This Product

(Waste Electrical & Electronic

Equipment)

(Applicable in the European Union and other European

countries with separate collection systems)

This marking shown on the product or its literature, indicates

E

that it should not be disposed with other household wastes at

the end of its working life. To prevent possible harm to the

environment or human health from uncontrolled waste

disposal, please separate this from other types of wastes and

recycle it responsibly to promote the sustainable reuse of

material resources.

Household users should contact either the retailer where they

purchased this product, or their local government office, for

details of where and how they can take this item for

environmentally safe recycling.

Business users should contact their supplier and check the

terms and conditions of the purchase contract. This product

should not be mixed with other commercial wastes for

disposal.