Samsung SCC-C6407P: инструкция

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 1

SmartDome Camera

SCC-C6407(P)

Owner’s Instructions

E

êÛÍÓ‚Ó‰ÒÚ‚ÓÔÓθÁÓ‚‡ÚÂÎfl

RU

PL

Instrukcja obs∏ugi

Part : AB68-00547A(00)

Printed in China

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 3

Important Safety Instructions

Safety Precautions

1. Read these instructions.

The purpose of this information is to ensure proper use of this product to

2. Keep these instructions.

prevent danger or damage to property. Please be sure to observe all

3. Heed all warnings.

precautions.

4. Follow all instructions.

* The precautions are divided into "Warnings" and "Cautions" as

5. Do not use this apparatus near water.

distinguished below:

6. Clean only with dry cloth.

Warning: Ignoring this warning may result in death or serious injury.

7. Do not block any ventilation openings, Install in accordance with the

E

Caution: Ignoring this caution may result in injury or damage to property.

manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, or

other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding- type plug.

A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

Warning instructions alert you to

Caution instructions alert you to the

The wide blade or the third prong are provided for your safety. If the

a potential risk of death

potential risk of injury or

provided plug does not fit into your outlet, consult an electrician for

or serious injury.

damage to property.

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

Warning

apparatus.

11. Only use attachments/accessories specified by the manufacturer.

1. Be sure to use only the standard adapter which is specified in the

12. Use only with cart, stand, tripod, bracket, or table specified by the

specification sheet.

manufacturer, or sold with the apparatus.

Using any other adapter could cause fire, electrical shock, or damage to

the product.

2. When connecting the power supply and signal wires, check the external

connection terminals before connecting them. Connect the alarm signal

wires to the alarm terminals, the AC adapter to the AC power input

receptacle, and the DC adapter to the DC power input, making sure that

the correct polarity is observed.

(Connecting the power supply incorrectly may cause fire, electrical shock,

or damage to the product.)

13. Unplug this apparatus. When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

3. Do not connect multiple cameras to a single adapter.

14. Refer all servicing to qualified service personnel. Servicing is required

(Exceeding the capacity may cause abnormal heat generation or fire.)

when the apparatus has been damaged in any way, such as power-supply

(A falling camera may cause personal injury.)

cord or plug is damaged, liquid has been spilled or objects have fallen into

4. Securely plug the power cord into the power receptacle.

the apparatus the apparatus has been exposed to rain or moisture, does

(Insecure connection may cause fire.)

not operate normally, or has been dropped.

5. When installing the camera on a wall or ceiling, fasten it securely and

firmly. (A falling camera may cause personal injury.)

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 5

6. Do not place conductive objects (e.g., screwdrivers, coins, and metal

FCC STATEMENT

things) or containers filled with water on top of the camera. (Doing so may

cause personal injury due to fire, electrical shock, or falling objects.)

This device complies with Part 15 of the FCC Rules. Operation is subject to

7. Do not install the unit in humid, dusty, or sooty locations.

the following two conditions:

(Doing so may cause fire or electrical shock.)

(1) This device may not cause harmful interference, and

8. If any unusual smells or smoke come from the unit, stop using the product.

(2) This device must accept any interference received, including interference

In such case, immediately disconnect the power source and contact the

that may cause undesired operation.

service center. (Continued use in such a condition may cause fire or

electrical shock.)

Note: This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

E

9. If this product fails to operate normally, contact the store of purchase or

limits are designed to provide reasonable protection against harmful

your nearest service center. Never disassemble or modify this product in

interference when the equipment is operated in a commercial

any way. (SAMSUNG is not liable for problems caused by unauthorized

environment. This equipment generates, uses, and can radiate radio

modifications or attempted repair.)

frequency energy and, if not installed and used in accordance with the

10. When cleaning, do not spray water directly onto parts of the product.

instruction manual, may cause harmful interference to radio

(Doing so may cause fire or electrical shock.)

communications. Operation of this equipment in a residential area is

Wipe the surface with a dry cloth. Never use detergents or chemical

likely to cause harmful interference in which case the user will be

cleaners on the product, as this may result in discoloration of surface or

required to correct the interference at his own expense.

cause damage to the finish.

Caution

1. Do not drop objects on the product or apply strong shock to it. Keep away

from a location subject to excessive vibration or magnetic interference.

2. Do not install in a location subject to high temperature (over

122

°F

), low

temperature (below

14

°F

), or high humidity.

(Doing so may cause fire or electrical shock.)

3. Avoid a location which is exposed to direct sunlight, or near heat sources

such as heaters or radiators.

(Neglecting to do so may result in a risk of fire.)

4. If you want to relocate the already installed product, be sure to turn off the

power and then move or reinstall it.

5. Install in a well-ventilated location.

6. Remove the power plug from the outlet when there is a lightning storm.

(Neglecting to do so may cause fire or damage to the product.)

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘ ` 1-1

Before Usage

This is a basic instruction manual for the SCC-C6407(P) user.

It contains all the instructions needed to use the SCC-C6407(P)

from a simple introduction of the control locations and functions of

the SCC-C6407(P) to installation methods in the set up menu.

We recommend all users of the SCC-C6407(P) from the

E

advanced user who has used similar cameras before to the

general user to read the instruction manual before using.

The most frequently used feature in the SCC-C6407(P) would be

the SCC-C6407(P) Setup Menu.

The SCC-C6407(P) Setup Menu is explained in detailed in

"Chapter 3 Setup Menu Overview".

The instructional manual is best used when read from beginning

to end, but for users wanting to read only the part they need here

are the Chapter summaries.

"Chapter 1 SCC-C6407(P) Overview" includes a brief

introduction of the SCC-C6407(P), part names and functions, and

Switch Settings.

"Chapter 2 SCC-C6407(P) Installation" explains the installation

procedures of the SCC-C6407(P) and provides preparation and

installation environment requirements.

"Chapter 3 Setup Menu Overview" presents the structure of the

Setup menu for the SCC-C6407(P) including a detailed

explanation of the functions performed in each submenu.

"Appendix SCC-C6407(P) Product Specifications" contains

product specifications of the SCC-C6407(P) in itemized

categories.

1-1

1-2

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘ ` 1-3

Table of contents

4. ZONE SET ..................................................................................3-19

Before Usage...............................................................................................1-1

- PRIVACY ZONE .......................................................................3-19

- STYLE....................................................................................3-19

Chapter 1 SCC-C6407(P) Overview

............................................................1-5

SCC-C6407(P) Introduction...........................................................1-6

- BLANK ALL ABOVE...............................................................3-20

Locations of Control.......................................................................1-7

- BLANK ALL BELOW..............................................................3-20

FRONT...........................................................................................1-7

- PRYVACY ZONE MAP ..........................................................3-20

BACK .............................................................................................1-8

- SET ZONE AREA ...............................................................3-21

ADAPTER CONNECTION.............................................................1-9

- SET ZOOM .........................................................................3-22

INITIAL SETTING............................................................................................1-10

- REVERSE...........................................................................3-22

Setting RS-422A/RS-485 termination ............................................1-11

- EXIT ....................................................................................3-22

E

- ZONE DIR SET/ZONE AREA SET ...........................................3-22

Chapter 2 SCC-C6407(P) Installation

.........................................................2-1

- ZONE DIR SET .........................................................................3-23

Before Installing .............................................................................2-2

- ZONE AREA .............................................................................3-23

Preparing the Cables .....................................................................2-3

- LOCATION.............................................................................3-24

Cable Connection ..........................................................................2-4

- ZONE ID SET.........................................................................3-24

Installing SCC-C6407(P)................................................................2-5

- ZONE ENABLE ......................................................................3-24

Installing the Camera.....................................................................2-8

5. AUTO SET ..................................................................................3-25

Chapter 3 Setup Menu Overview

................................................................3-1

- AUTO PAN................................................................................3-25

Structure of the Setup Menu..........................................................3-2

- POSITION SET ......................................................................3-25

1. CAMERA SET ...........................................................................3-4

- DIRECTION ...........................................................................3-26

- CAMERA ID.............................................................................3-4

- ENDLESS ..............................................................................3-26

- V-SYNC ...................................................................................3-5

- SPEED...................................................................................3-26

- COLOR/BW .............................................................................3-6

- DWELL TIME .........................................................................3-26

- MOTION DET ..........................................................................3-7

- PATTERN .................................................................................3-26

- ZOOM SPEED.........................................................................3-8

- SCAN ........................................................................................3-27

- DIGITAL ZOOM.......................................................................3-9

- AUTO PLAY ..............................................................................3-28

- DISPLAY ZOOM......................................................................3-9

- AUTO RETURN .....................................................................3-28

- DISPLAY P/T...........................................................................3-9

- AUTO PLAY...........................................................................3-28

- EXIT.........................................................................................3-10

- PLAY NUMBER .....................................................................3-28

2. VIDEO SET ...............................................................................3-10

6. ALARM SET ................................................................................3-29

- IRIS..........................................................................................3-10

- ALARM PRIORITY SET............................................................3-29

- ALC.......................................................................................3-10

- ALARM IN SET .........................................................................3-29

- BLC.....................................................................................3-10

- ALARM OUT SET .....................................................................3-29

- WDR .....................................................................................3-11

- AUTO SET ................................................................................3-30

- MANU ...................................................................................3-11

- AUX OUT CONTROL................................................................3-30

- SHUTTER................................................................................3-12

7. OTHER SET................................................................................3-30

- FLICKERLESS ........................................................................3-12

- PROPORTINAL P/T..................................................................3-30

- AGC.........................................................................................3-13

- MOTION ..................................................................................3-13

- TURBO P/T ...............................................................................3-31

- WHITE BAL .............................................................................3-14

- AUTO CAL ................................................................................3-31

- DIS...........................................................................................3-15

- D-FLIP.......................................................................................3-31

- FOCUS MODE ........................................................................3-16

- CAM RESET .............................................................................3-31

- SPECIAL..................................................................................3-16

- LANGUAGE ..............................................................................3-31

- EXIT.........................................................................................3-16

- PASSWORD .............................................................................3-31

3. PRESET.....................................................................................3-17

8. SYSTEM INFO ............................................................................3-32

- POSITION SET........................................................................3-18

9. SHORT KEYS .............................................................................3-33

- PRESET ID..............................................................................3-18

- VIDEO SET..............................................................................3-18

Product specifications ............................................................................3-35

- PRESET SPEED .....................................................................3-18

- DWELL TIME...........................................................................3-18

- IMAGE HOLD ..........................................................................3-18

- EXIT.........................................................................................3-18

1-3

1-4

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘ ` 1-5

SCC-C6407(P) Introduction

Chapter 1 SCC-C6407(P) Overview

SCC-C6407(P) is a zoom lens built in smart dome camera which

provides you with the best monitoring function in connection with

In this chapter we will briefly introduce the SCC-C6407(P) and

CCTV at banks or companies.

E

show main functions, locations of control and Switch Setting.

The SCC-C6407(P) is a high quality surveillance camera using x32

zoom lens and digital zoom IC, it can catch clear images up to 320

times.

SCC-C6407(P) has a variety of functions such as;

- WDR to cover the full screen irregardless of its brightness,

- DAY/NIGHT to improve the sensitivity by automatic conversion

into the black and white mode at night or in the environment with

low illumination,

- White Balance to control the brightness to the illumination,

- Backlight Compensation under spotlight or utmost bright

illumination,

- Auto Focus to automatically adjust the focus to the subject

movement,

- Privacy zone to hide a specific area for personal privacy, and,

- PAN/TILT for precise control at high speed.

The SCC-C6407(P) uses an Alarm function for alert situations and

moving camera in the direction you want, ZOOM-IN and

ZOOM-OUT functions can be remote controlled.

1-5

1-6

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘ ` 1-7

Locations of Control

FRONT

BACK

E

1-7

1-8

INITIAL SETTING

CAMERA ADDRESS SETUP

Use SW701, SW702, or 703 for Camera Address setup. You may allocate

up to 255 addresses by using SW701 to set the 3rd digit, SW702 the 2nd

digit, and SW703 the 1st digit.

EX) In case of Camera Address 1, see the following figure for setup.

E

SW701

SW702

SW703

Setting communication Protocol

Use number 1~4 PIN of SW704 to set communication Protocol.

PIN

Comp

PIN1 PIN2 PIN3 PIN4

A : SAMSUNG HALF

A OFF OFF OFF OFF

B : SAMSUNG FULL

B ON OFF OFF OFF

C OFF ON OFF OFF

D ON ON OFF OFF

E OFF OFF ON OFF

F ON OFF ON OFF

G OFF ON ON OFF

H ON ON ON OFF

I OFF OFF OFF ON

J ON OFF OFF ON

K OFF ON OFF ON

L ON ON OFF ON

M OFF OFF ON ON

N ON OFF ON ON

O OFF ON ON ON

PONONONON

Baud Rate Setting

Use PIN 5 and 6 of SW704.

1 2 3 4 5 6 7 8

ON

OFF

BAUD RATE

PIN 5

PIN 6

4800 BPS

ON

ON

9600 BPS

OFF

ON

19200 BPS

ON

OFF

38400 BPS

OFF

OFF

1-9

1-10

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘ ` 1-9

ADAPTER CONNECTION

SCC-C6407(P) Adapter BOARD

(BOTTOM VIEW)

SW 704

The factory default setting is set to 9600BPS.

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘ ` 1-11

Setting RS-422A/RS-485 termination

Chapter 2 SCC-C6407(P) Installation

As it is shown in the structure map, when Controller and RS-422A/RS-

485 is connected it should be terminated according to the Cable feature

of impedance on the each end of the transmitting line to transfer the

E

In this chapter, we will check the contents of the package before

signals in long distance by controlling the reflection of the signals to the

installing the SCC-C6407(P), and prepare a power adapter suitable

lowest.

for the power supply system.

(Power Consumption: 22W; Voltage: AC24V, 1.5A)

Division

n < 32

Then, we will install the SCC-C6407(P) and connect the cables.

Termination

SW1-ON

<RS-485 Half Duplex Organization>

Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.

n < 32

Division

SW1-ON

SW2-ON

Division

<RS-422A/RS-485 Full Duplex Organization>

❈

A communication error may occur if you connect multiple cameras

that are assigned the same address in the network.

1-11

2-1

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 3-5

(CAMERA SET)

(CAMERA ID)

COLOR/BW

CAMERA ID ON...

A B C D E F G H I J K L

In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.

V-SYNC INT

COLOR/BW COLOR...

➜

M N O PQ R S T U V W X

MOTION DET OFF

Y Z 0 1 2 3 4 5 6 7 8 9

In a poor illumination environment, the IR filter is turned off in the BW mode the its

ZOOM SPEED 3

Press

: ! - + ✽ ( ) /

sensitivity increases as high as a black and white camera. On the other hand, the

DIGITAL ZOOM OFF

DISPLAY ZOOM OFF

[Enter]

SP

ï î

SP

IR filter is turned on and the sensitivity decreases in the COLOR mode.

DISPLAY P/T OFF

LOCATION...

RET

COLOR : The IR Filter is ON and the screen is normal. You can press the

EXIT QUIT

SCC-C6407(P)P........

[Enter] key to set the COLOR GAIN LEVEL. And when the AGC

function is on, you can set the AGC COLOER LEVEL.

* " ... " Means there are Sub Menus.

(CAMERA SET)

(COLOR)

CAMERA ID OFF

E

V-SYNC

V-SYNC INT

➜

COLOR/BW COLOR …

In the V-SYNC menu, vertical synchronization can be selected. The

MOTION OFF

ZOOM SPEED 3

Press

vertical synchronization signal supported by the SCC-C6407(P) is the INT

DIGITAL ZOOM OFF

[Enter]

mode made by clock inside the SCC-C6407(P) and LINE mode adjusting

DISPLAY ZOOM OFF

GAIN (0)I--------

DISPLAY P/T OFF

AGC COLOR (0)----I----

vertical synchronization to the exterior power frequency.

EXIT QUIT

RET

Select LINE and press [Enter]. You will see the LINE LOCK submenu

where you can adjust the phase of the LINE LOCK.

You can use the PHASE menu of the LINE LOCK submenu to assign as

BW : The IR Filter is OFF and the screen is black and white.

much PHASE as you want.

(Sensitivity to low light is increased to a level comparable to a black

and white camera.)

Select BW and press [ENTER] and the additional menu to select

(CAMERA SET)

(LL-PHASE)

BURST ON/OFF will appear.

CAMERA ID OFF

V-SYNC LINE...

AUTO : Select to automatically switch between the COLOR mode and BW

COLOR/BW COLOR...

➜

MOTION DET OFF

mode depending on the amount of light. In low light conditions, the

ZOOM SPEED 3

Press

IR Filter is turned OFF and the sensitivity to low light is increased

DIGITAL ZOOM OFF

[Enter]

DISPLAY ZOOM OFF

by switching to the BW mode, but in bright light conditions, the IR

DISPLAY P/T OFF

PHASE (-106)I--------

Filter is turned ON and the sensitivity is decreased by switching to

EXIT QUIT

RET

the COLOR mode.

Select AUTO and press [ENTER] and the additional menu to select

BW LEVEL and DURATION will appear.

- BURST ON : The color burst signal is output together with black and white

composite video signal.

- BURST OFF : The color burst signal is not output.

- LEVEL : You can set the brightness level that changes from COLOR mode

to BW mode in 3 steps : LOW, MEDIUM, and HIGH.

- DURATION : Set the HOLDING time for switching between COLOR and BW

mode depending the changes in the amount of light. You can set

the HOLDING time to 10sec (S), 30sec, 60sec, or 300sec( L).

3-5 3-6

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 3-7

Select ON and press [ENTER] and the MOTION DET additional menu will

❈ In AUTO mode, AGC will be displayed as “---“. You can’t adjust the

settings manually.

appear. The AREA menu, selecting the screen area where the MOTION

detection function will be applied may be selected by PRESET or USER.

Set AREA to PRESET and the MOTION detection function will be applied to

(CAMERA SET)

(AUTO)

the factory default part.

CAMERA ID OFF

If you set the AREA menu to USER and press [ENTER], you may vary the size

V-SYNC INT

➜

COLOR/BW AUTO...

and position of the area where you want to apply the MOTION detection

MOTION DET OFF

Press

ZOOM SPEED 3

function by yourself. Press Left, Right, Up, or Down to select an area size.

DIGITAL ZOOM OFF

[Enter]

BURST ON

DISPLAY ZOOM OFF

Press ENTER and then Left, Right, Up, or Down to select a position. Press

DISPLAY P/T OFF

LEVEL LOW

DURATION S --|---- L

ENTER again to move back to the upper menu.

EXIT QUIT

RET

Use [ENTER] and Left, Right, Up, or Down to move and scale the MOTION

E

detection area.

Press [ENTER] again and you will escape the AREA setup menu.

Use SENSITIVITY to set up the sensitivity of MOTION detection strength.

Caution : If you use an infrared light source while in AUTO mode, AUTO

The higher, the more sensitive.

switching malfunction and camera AF malfunction may occur.

SIZE

SIZE

➜

Use the [Left,

Right, Up, Down]

MOTION DET

Keys

In MOTION DET, you can set the Motion Detection function, Motion Detection

POSITION

Sensitivity, and the Area of Motion Detection. If the Motion Detection function

POSITION

is set, the movement of an intruder can be detected. When motion is detected,

it sets off the Alarm signal of the Controller.

❈

After PAN/TILT/ZOOM/FOCUS/IRIS movement finishes, MOTION DET

function will not work for about 5 seconds to stablize the chage of the

(CAMERA SET)

(MOTION DET)

screen.

CAMERA ID OFF

➜

V-SYNC INT

❈

MOTION detection function operates based on the brightness change

COLOR/BW COLOR...

MOTION DET ON...

Press

within the setup region. Therefore, erroneous operation may occur

ZOOM SPEED 3

[Enter]

depending on the brightness difference between the background and

DIGITAL ZOOM OFF

DISPLAY ZOOM OFF

the object that is being taken, or the status of the area setup, etc.

DISPLAY P/T OFF

AREA PRESET...

SENSITIVITY

L ---|--- H

EXIT QUIT

RET

ZOOM SPEED

In the ZOOM SPEED menu you can select the speed of the ZOOM Key

(Tele/Wide).

Use the [Left] or [Right] keys in the ZOOM SPEED menu to select

the speed.

1 : Magnification x 32 takes about 22 seconds. Slowest speed

2 : Magnification x 32 takes about 10 seconds. Low speed

3 : Magnification x 32 takes about 7 seconds. High speed

4 : Magnification x 32 takes about 5 seconds. Fastest speed

3-7

3-8

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 3-9

DIGITAL ZOOM

EXIT

You may set up the digital zoom magnification ratio in the DIGITAL ZOOM

The EXIT menu is used to quit the CAMERA SET menu of the

menu. The magnification ratio ranges from OFF to 10. If you set Digital

SCC-C6407(P) and return to the MAIN MENU.

Zoom of SCC-C6407(P) to max. 10 times, the mode will become the 32 time

- QUIT : Ignores the changed information and restores the saved

information.

optical zoom and you will be able to enlarge a subject by max. 320 times.

- SAVE : Saves the information of the setting condition of the menu.

Use Left or Right to select a magnification ratio in the DIGITAL ZOOM menu.

- PRESET: Ignores the changed information and restores the initial

factory defaults of the menu.

(CAMERA SET)

(CAMERA SET)

2. VIDEO SET MENU

CAMERA ID OFF

CAMERA ID OFF

V-SYNC INT

V-SYNC INT

COLOR/BW BW...

COLOR/BW BW...

IRIS

E

MOTION DET OFF

MOTION DET OFF

ZOOM SPEED 3

ZOOM SPEED 3

There is a function to automatically adjust IRIS to the incoming light level.

DIGITAL ZOOM OFF

DIGITAL ZOOM X10

Owing to this function, you may set up the brightness level yourself.

DISPLAY ZOOM OFF

DISPLAY ZOOM OFF

DISPLAY P/T OFF

DISPLAY P/T OFF

The ALC(Auto Light Control) menu allows you for video output level setup.

EXIT QUIT

EXIT QUIT

ALC

Choose the ALC of the IRIS item and press [ENTER] and set he submenu

DISPLAY ZOOM

to the Video Output level and BLC will be shown.The Video Output Level

can be set in the level item using the [Left, Right] keys.

In DISPLAY ZOOM, you can display the ZOOM scale on the screen.

(CAMERA SET)

BLC (Submenu of the ALC menu)

X020

CAMERA ID OFF

If you use a general camera to photograph a subject under backlight or

V-SYNC INT

bright illumination, the subject will be shown dark on the monitor due to

COLOR/BW COLOR...

MOTION DET OFF

the backlight. BLC(Back Light Compensation) is used to prevent such a

ZOOM SPEED 4

backlight problem to secure distinct images under bright illumination.

DIGITAL ZOOM OFF

DISPLAY ZOOM ON

Using the [Left, Right] keys, you can set up BOTTOM…, TOP…, LEFT…,

DISPLAY P/T OFF

RIGHT…, CENTER… 5 preset areas and the USER…function that can

EXIT SAVE

directly set the areas. For example, for the items in the BLC menu, you

can confirm the preset BOTTOM area by pressing [ENTER] key in the

BOTTOM… status.

❈ If no change on the ZOOM scale is made for 3 seconds, the

information window will disappear.

(VIDEO SET)

(ALC)

IRIS ALC...

SHUTTER AUTO X2...

➜

DISPLAY P/T

MOTION NORM

WHITE BAL ATW1

Press

In DISPLAY P/T, you can display the position of Pan/Tilt on the screen.

DIS ---

[Enter]

FOCUS MODE ONEAF

SPECIAL ...

BLC OFF

(CAMERA SET)

LEVEL (0)----I----

X020

CAMERA ID OFF

EXIT QUIT

RET

V-SYNC INT

COLOR/BW COLOR...

MOTION DET OFF

ZOOM SPEED 4

(ALC)

DIGITAL ZOOM OFF

DISPLAY ZOOM OFF

DISPLAY P/T ON

➜

EXIT SAVE

Press

[Enter]

❈ If no change on the Pan/Tilt position is made for 3 seconds, the

BLC BOTTOM...

LEVEL (0)----I----

information window will disappear.

RET

3-9

3-10

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 3-11

For items in the BLC menu, the user can set the size and location of the

(VIDEO SET)

(MANUAL)

BLC area by pressing [ENTER] key after put the cursor on USER… using

the [Left, Right] key. For SIZE items, you can use the [Up, Down, Left,

IRIS MANU...

Right] key to designate the SIZE, and then press the [ENTER] key.

SHUTTER OFF

You can set the location for areas using the [Up, Down, Left, Right] key in

AGC OFF

Press the

the LOCATION.

WHITE BAL ATW1

DIS OFF

ENTER

FOCUS MODE ONEAF

button.

(ALC)

SIZE

SPECIAL ...

LEVEL (00) ----I----

EXIT QUIT

RET

➜

SHUTTER

Press

[Enter]

You may designate both the fast electronic shutter speed and low

BLC USER...

electronic shutter speed in the SHUTTER menu. The fast electronic

E

LEVEL (0) ----I----

shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to

RET

LOCATION

be used for the bright and fast video image. The AUTO slow electronic

shutter supports 10 shutter speeds from x2 to x160 and sets the shutter

speed to be slow In order to make the image on the screen more distinct

SIZE

SIZE

and brighter when you photograph under dark illumination. If you want to

sense the light brightness to control the shutter speed to the brightness

automatically, select the AUTO slow shutter.

➜

(VIDEO SET)

Press

[Enter]

IRIS ALC...

SHUTTER OFF

AGC

OFF

LOCATION

LOCATION

WHITE BAL ATW1

DIS OFF

FOCUS MODE ONEAF

Use [Left, Right] key in the LEVEL menu to control the video output

SPECIAL ...

EXIT QUIT

level(brightness).

WDR

Keep pressing both Left and Right in the SHUTTER menu, the speed will

change in the following sequence.

The WDR camera is a state-of-art technology to expand the screen profit,

➝ OFF ➝ AUTO X2 ➝ AUTO X4 ➝ AUTO X6 ➝ AUTO X8 ➝ AUTO X12 ➝

mostly effective when you photograph both indoor and outdoor. In short,

AUTOX16 ➝ AUTO X20 ➝ AUTO X40 ➝ AUTO X80 ➝ AUTO X160 ➝ OFF ➝

this function provides you with the distinct reproduction of not only the

1/100(1/120) ➝ 1/250 ➝ 1/500 ➝ 1/1000 ➝ 1/2000 ➝ 1/4000 ➝ 1/10K

indoor but also the outdoor. Press [ENTER] to set up the WDR leve.

❈ In case the IRIS mode is set to WDR, only the following modes are

(VIDEO SET)

(WDR)

available.

➝ OFF ➝ AUTO X2 ➝ AUTO X4 ➝ AUTO X6 ➝ AUTO X8 ➝ AUTO X12 ➝

IRIS WDR...

➜

SHUTTER

OFF

AUTOX16 ➝ AUTO X20 ➝ AUTO X40 ➝ AUTO X80 ➝ AUTO X160

AGC

OFF

Press

WHITE BAL ATW1

DIS ON

[Enter]

LEVEL1 L----

I ----H

❈ If you set SHUTTER to between AUTO X4... and AUTO X128..., FOCUS mode will be

FOCUS MODE ONEAF

LEVEL2 L----I ----H

displayed as “MF“ (the product can operate only in MF mode). You can ’t adjust the

SPECIAL ...

EXIT QUIT

settings manually. If you set it to OFF, 1/100(1/120)/10K or AUTO X2..., the product

RET

will recover the previous FOCUS mode.

❈ If you set SHUTTER to between AUTO X2... and AUTO X128..., DIS will be displayed

- LEVEL 1 : Controls the shutter speed while WDR operates.

as “---“ (it can only operate in Off mode). You can ’t adjust the settings manually. If you

- LEVEL 2 : Controls the whole brightness while WDR operates.

set it to OFF or 1/100(1/120)/10K, the product will recover the previous settings of DIS.

FLICKERLESS

MANU

Either NTSC (for 50 Hz)or PAL (for 60 Hz areas)is an anti-flickering system that is designed

When you press [ENTER] key after selecting MANU in the IRIS item, an

to avoid image flickering on the screen due to inconsistency between the vertical

additional screen appears in which you can set manually opening or closing

synchronizing frequency of the picture and the flashing frequency of the lightening. If you

the IRIS.

select and set AUTO to ON in SHUTTER from VIDEO SET, you can set NTSC or PAL for

your area and the auto shutter speed is fixed at 1/100(1/120) second.

3-11

3-12

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 3-13

(VIDEO SET)

(FLICKERLESS)

WHITE BAL

IRIS ALC...

Lights are generally denoted as color temperatures and expressed in

SHUTTER AUTOX2...

➜

Kelvin (

K

) units.

MOTION NORM

WHITE BAL ATW1

The general light color temperatures are shown below.

DIS ---

Press

FOCUS MODE ONEAF

[Enter]

SPECIAL ...

FLICKERLESS OFF

EXIT QUIT

RET

10000K

Blue sky

AGC

The AGC menu was designed to provide you with brighter screen supposed you

9000K

Rainy

photographed any subject in the dark resulting in less brighter image than

E

regulated. AGC menu setup is available only when the SHUTTER menu is set to

Fast Shutter or Off. Press either Left and Right to go to LOW or HIGH and the

8000K

AGC function will be activated. LOW is use to lower the maximum AGC GAIN and

HIGH raise the maximum AGC GAIN.

Cloudy

7000K

(VIDEO SET)

IRIS ALC...

SHUTTER OFF

AGC

LOW

6000K

Partly Cloudy

WHITE BAL ATW1

DIS OFF

FOCUS MODE ONEAF

SPECIAL ...

Sunny

5000K

EXIT QUIT

4000K

Fluorescent lamp

❈ When the COLOR/BW menu of the camera set is set to AUTO...,

AGC will be displayed as “---“. You can’t adjust the settings manually.

3000K

Halogen lamp

MOTION

The MOTION function is available only when the SHUTTER men is set to Slow Shutter

AUTO, being composed of 5 steps, S.SLOW, SLOW, NORM, FAST, F.FAST.

2000K

● S.SLOW reduces the amount of AGC as much as possible to monitor subjects with no

Tungsten lamp

immobility in the dark.

● SLOW reduces the amount of AGC to monitor subjects with little immobility in the dark.

Candlelight

● NORM sets the amount of AGC to the middle to monitor mobile subjects in the dark.

1000K

● FAST raises the amount of AGC to monitor fast subjects in the dark.

● F.FAST reduces the amount of AGC as much as possible to monitor very fast subjects in

the dark.

When the SHUTTER menu is set to AUTO, press Down to locate the cursor in the MOTION

menu and press Left and Right for MOTION function setup. Press Left to the SLOW side and

Right to the FAST side.

(VIDEO SET)

IRIS ALC...

SHUTTER AUTO X2...

MOTION F.FAST

WHITE BAL ATW1

DIS ---

FOCUS MODE ONEAF

SPECIAL ...

EXIT QUIT

3-13

3-14

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 3-15

You can select one of four modes for white balance adjustment as follows:

FOCUS MODE

In the FOCUS MODE MENU, the Focus method can be set to ONEAF(One Auto

- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the

Focus), or MF(Manual Focus).

color temperature is monitored continuously and thereby white balance is

set automatically. The following are the approximate supported color

- ONEAF : In the ONEAF mode, it automatically sets the focus after the zoom moves,

temperature ranges in these modes.

and operates as the same in the MF mode if the zoom does not move.

ATW1 : 2500K ~ 9300K(

✻

1)

- MF : In MANUAL FOCUS MODE the user adjusts the Focus manually.

ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(

✻

2)

Use the left/right keys to select ONEAF orMF in the FOCUS MODE menu.

✻

1. If the color temperature is out of this range in ATW1 mode, proper

(VIDEO SET)

white balance may not be obtained. In that case, select ATW2 mode.

IRIS ALC...

✻

2. In ATW2 mode, if one color is dominated in the shooted area, the

SHUTTER

OFF

E

color can be displayed differently.

AGC

LOW

WHITE BAL ATW1

Therefore, select the mode which is appropriate for the environment.

DIS OFF

- AWC(Auto-Tracing White Balance Control): In this mode, accurate white

FOCUS MODE ONEAF

SPECIAL ...

balance is obtained by pressing [ENTER] while having a white paper in

EXIT QUIT

front of the camera. White Balance data will be maintained after set it

once. AWC mode is best in locations where the color temperature of light

source is constant.

❈

The ONEAF setting can be selected only when OFF,

- MANU : If WHITE BAL menu is set to MANU mode, the user can set the

1/100(1/120)~1/10K, AUTO X2 is selected for the SHUTTER menu. Any

white Balance considering the current illumination. Select MANU item

Other SHUTTER setting(AUTO X4~AUTO X160) causes MF to be

and press [ENTER], the sub screen where you can select Manual White

selected automatically for the FOCUS MODE menu.

Balance will be shown. Use the left/right keys to select 3200K, 5600K or

❈

ONEAF function may not possible withe types of objects listed below. For

OFF(USER) mode in the PRESET menu.

such objects, focus manually.

- 3200

K

: Set color temperature to 3200

K

- High intensity objects or objects illuminated with low lighting

- 5600

K

: Set color temperature to 5600

K

- Obejects shot through wet or dirty glass

- USER : Choose out a proper value from the RED and BLUE graph for

- Pictures that are a mixture of distant and nearby objects

color and temperature setup.

- White alls and other single-color objects

- Venetian blinds and other horizontally striped objects

(VIDEO SET)

(AWB/MANUAL)

IRIS ALC...

SPECIAL

SHUTTER

OFF

➜

AGC

ON

Press

In SPECIAL menu, you can directly adjust REVERSE, Y-LEVEL, C-LEVEL,

WHITE BAL MANU...

DIS ON

[Enter]

and DETAIL functions.

PRESET 3200K

FOCUS MODE ONEAF

- REVERSE : Mirrors the screen horizontally, vertically, or in all directions.

SPECIAL ...

EXIT QUIT

RET

- Y-LEVEL : It is used to set the levels for the Sync signal and the entire

brightness signal of the video signal.

- C-LEVEL : It is used to set the levels for the Burst signal and the entire colour

DIS

signal of the video signal.

The DIS(Digital Image Stabilization) function compensates the camera

- DETAIL : Controls both horizontal and vertical distinction.

screen shaking incurred from vibration.

(VIDEO SET)

(SPECIAL)

IRIS ALC...

❈ It is recommended to deactivate the DIS function in the no vibration

SHUTTER OFF

➜

environment.

AGC LOW

WHITE BAL ATW1

Press

REVERSE OFF

❈ From VIDEO SET, if you set SHUTTER to between AUTO X2... and

DIS OFF

[Enter]

Y-LEVEL (0)I--------

FOCUS MODE ONEAF

AUTO X128... DIS will be displayed as “---“ (it can operate only in

C-LEVEL (0)I--------

SPECIAL ...

DETAIL (0)--I-

Off mode). You can’t adjust the settings manually.

RET

EXIT QUIT

3-15

3-16

00547A_C6407P-E+R+P 6/5/06 10:41 AM ˘` 3-17

EXIT

POSITION SET

It's the same as the EXIT function of the CAMERA SET menu.

From "POSITION SET..." press [ENTER] to get into the PAN/TILT,

FOCUS/ZOOM SET screen

to set the PAN/TILT location and FOCUS/ZOOM condition then press

[ENTER] to return to a higher menu.

PRESET ID

3. PRESET

This is the ID set up function for each PRESET.

This is the menu that user sets the PAN/TILT location, Zoom/Focus, and

It can be set up to 12 characters using the left, right, up, and down keys.

screen condition, so the camera can monitor the presetting area on

The ID location can be set in the submenu of "LOCATION..."

E

demand. A total of 128 presets are available.

VIDEO SET

This is the screen setting function for each PRESET.

Refer to the explanation under "VIDEO SET menu".

* * MAIN MENU * *

(PRESET MAP)

CAMERA SET...

PRESET SPEED

VIDEO SET...

0 1 2 3 4

PRESET ...

➜

5 6 7 8 9

This function sets up the speed of PAN or TILT by 8 steps from 1(SLOW)

ZONE SET...

10 11 12 13 14

to 8(FAST).

AUTO SET...

Press

15 16 17 18 19

[Enter]

20 21 22 23 24

- PRESET SPEED 1 : Maximum PAN moving speed of 240°/sec

ALARM SET...

25 26 27 28 29

OTHER SET...

- PRESET SPEED 8 : Maximum PAN moving speed of 400°/sec

30 31

î ï

RET

SYSTEM INFO...

ID:PRESET 0

DWELL TIME

This is a function setting for the DWELL TIME of the PRESET location in

"SCAN" motion. It can set DWELL TIME From 1 ~ 60 Sec.

PRESET NO.0

IMAGE HOLD

POSITION SET ...

➜

PRESET ID ON...

Pauses the image when PRESET is in movement, If you set the IMAGE

VIDEO SET OFF

Press

HOLD menu to ON, the screen will be paused until PRESET finishes

PRESET SPEED 8

[Enter]

DWELL TIME 3S

moving.

IMAGE HOLD OFF

EXIT QUIT

EXIT

"QUIT" : Does not save the selected information and returns to a higher

menu.

"SAVE" : Do saves the selected information and returns to a higher menu.

"DEL" : Deletes the selected information and restores the DEFAULT.

❈

Set the PRESET position at the TILT which ranges from 0° to 90°. Beyond

Then returns to a higher menu.

this range, PRESET setup is not available.

❈

When you try to set the Preset position by using the Controller(SSC-1000

or SSC-2000) beyound the range of TILT 90°, the text, “SET AGAIN” will

be displayed. In such a case, please retry in the area below TILT 90°.

3-17

3-18