Philips SRU5120: инструкция

Register your product

Universal remote control

and get support at

www.philips.com/welcome

SRU 5120/87

EN Remote control 3

IT Telecomando 12

ES Mando a distancia 21

PT Telecomando 31

GR

∆ËϯÂÈÚÈÛÙ‹ÚÈÔ

40

TR Uzaktan kumanda 50

RU пульта ДУ 60

PL Pilota 70

CS Dálkového ovládání 79

2

Table of contents

ENGLISH

1 Your universal remote control 3

2 Installing the remote control 3-7

2.1 Inserting the batteries 3

2.2 Testing the remote control 4

2.3 Setting the remote control 4-6

3 Keys and functions 7-8

4 Extra possibilities 8-9

4.1 Adjusting device selection (Mode keys) 8-9

4.2 Restoring the original remote control settings 9

5 Frequently asked questions 10

6 Need help? 11

Code list of all brands / equipment 88-97

Information to the Consumer 100

1 Your universal remote control

Congratulations on your purchase and welcome to Philips.

To fully benefit from the support that Philips offers, register your product

at www:philips.com/welcome.

For quick, clean and easy setup go to: www.philips.com/urc

After installing the universal remote control SRU 5120 you can operate a

maximum of 2 different devices with it:

TV and DVD player/HDD/recorder or VCR.

2 Installing the remote control

2.1 Inserting the batteries

1

Press the cover inwards and slide it in the direction of the arrow.

1

1

2

Place two AAA type batteries into the battery compartment, as

shown.

3

Replace the cover and click it firmly into place.

3Installing the remote control

2.2 Testing the remote control

ENGLISH

The remote control has been programmed to operate most Philips

devices. Because the SRU 5120 may use different signals for each brand

and even for different models of the same brand, it is advisable to test

whether your device responds to the SRU 5120.The example below (TV)

instructs you how to do this.You can repeat the same steps for other

devices (DVD player/recorder or VCR) which you want to operate using

the SRU 5120.

Example of TV:

1

Turn your TV on manually or use the original remote control.Tune to

channel 1.

2

Press the TV key to select TV.

• The key lights up.

2

• If the key does not light up, check whether the batteries are

properly inserted (see ‘2.1 Inserting the batteries’).

2

3

Check whether all the keys are working.

3

For an overview of the keys and their functions see

‘3. Keys and functions’.

• If the TV responds as it should to all of the key commands the SRU 5120

is ready for use.

3

Tip

If the device does not respond at all or not to all of the key commands,

follow the instructions under ‘2.3 Setting the remote control’, or for

online setup go to: www.philips.com/urc.

2.3 Setting the remote control

This is only necessary if your device does not respond to the SRU 5120.

If that is the case, the SRU 5120 does not recognize the brand and/or

model of your device and you need to program the remote control to do

so.The example below (TV) instructs you how to do this.

You can repeat the same steps for other devices (DVD player/ recorder

or VCR) which you want to operate using the SRU 5120.

4 Installing the remote control

Example of TV:

1

Turn on the TV manually or use the original remote control.Tune in

to channel 1.

2

Look up the brand of your TV in the code list at the back of this

ENGLISH

manual.A four-figure code is shown for each brand.

Note the code for your brand.

4

4

Be careful! There are separate tables for TV, DVD and VCR.

Make sure you use the codes from the correct table.

3

Press the TV key until it flashes twice and then remains lit.

5

5

4

Then enter the code noted in step 2 using the numeric keys.

6

6

• The TV key now flashes twice.

• If the key flashes once for an extended period, the code has not

been entered properly or the wrong code has been entered. Start

again from step 2.

5

Press and hold the Stand-by key of the SRU 5120 until your TV

switches off (stand-by).

7

Then release the key immediately.

7

• The SRU 5120 is now set to operate your TV.

5Installing the remote control

6

Check if you can operate all functions on your TV with the SRU 5120.

ENGLISH

• If a key does not function properly, keep it pressed until it works.

Then release the key immediately.

Repeat this for every key that does not work.

• If the TV responds to all of the key commands, the SRU 5120 is

ready for use. Do not forget to note your code.

7

Keep the TV key pressed for 5 seconds to exit setup mode.

8

• When no key is pressed for 2 minutes or more the remote control will

exit setup mode automatically.

When setting the remote control for other devices, be sure to enter

and exit setup mode with the appropriate mode key. DVD for DVD

player/ recorder and VCR.

Full search setup

If your code does not work or if the brand of your device is not

mentioned in the code list, you can try setting the remote control with

full search setup.

1

Press the mode key of the device you wish to set up the remote

control for. E.g. the TV key.

Press the key until it flashes twice and then remains lit.

9

9

2

Press and hold the Stand-by key of the SRU 5120 until your TV

switches off (stand-by).

10

Then release the key immediately.

10

• The SRU 5120 is now set to operate your TV.

Full search setup takes about 5 minutes.

6

Installing the remote control