Karcher CV 60-2 RS Bp-: Transport Storage Maintenance and care

- 

5



Step on the standing platform.



Do not press the accelerator pedal.



Release emergency-stop button by 

turning.



Set main switch to “1”.



Turn the program selection switch to 

the desired cleaning program. 



Set the forward drive direction using the 

drive direction button at the operator 

console.



Press accelerator pedal and drive to the 

surface to be cleaned.



Set programme selection to "Drive".



Park the machine on an even surface.



Turn key to "0" and remove it. 



Park the machine on an even surface.



Turn key to "0" and remove it. 



Open the lock.



Swivel the top of the appliance forward.



Remove the protective film from the clo-

sure of the filter bag.



Adhere the closure to the opening in the 

filter bag.



Remove the filter bag from the waste 

container and dispose of it.



Insert new filter bag (see "Replacing fil-

ter bag").



Danger

Risk of injury! When loading or unloading 

the machine, it may only be operated on 

gradients of max. 10%. Drive slowly.

Caution

Risk of injury and damage! Observe the 

weight of the appliance when you transport 

it.



When transporting in vehicles, secure 

the appliance according to the guide-

lines from slipping and tipping over.

Fastening points

Caution

Risk of injury and damage! Note the weight 

of the appliance in case of storage.

This appliance must only be stored in inte-

rior rooms.



Danger

Risk of injury! Before carrying out any tasks 

on the machine, set the main key to "0" and 

remove it.  Pull out the battery plug.

Note

Suction turbine will continue to run for a 

while after switch-off. Carry out mainte-

nance tasks only after the suction turbine 

has come to a halt.



Check the seal of the waste container.



Check tyre status.



Check the suction hose for contamina-

tion.



Check the inserts of the suction hose 

for leaks. 



Empty and clean the coarse dirt pan.



Check the filter bag, replace if required



Check accelerator pedal, brake and 

steering wheel for correct functioning.



Check acid level in wet batteries; refill 

distilled water, if required.



Empty and clean the coarse dirt pan.



Check brushes for wear and tear and 

clean them.



Check device externally for damage. 



Charge battery.



Clean upper side of the batteries. 



Check acid density in wet batteries. 



Check battery cable for correct position-

ing. 



Clean battery room and battery casing. 



Check the tension of the drive chains on 

the drive. *



Check drive belt for wear and tear.



Check the ropes, chains and pulleys of 

the lift drive.



Check immobilising brake. *



Check carbon brushes and commuta-

tors of all motors for wear and tear. *



Check tension of steering chain. *

* To be done by Customer Service.

To ensure a reliable operation of the appli-

ance maintenance contracts can be con-

cluded with the competent Kärcher sales 

office.

1 Coarse dirt pan

2 Lock



Press the closure to the side and re-

move the coarse dirt pan.

The brush rollers are considered worn, if 

the bristles have the same length as the 

yellow indicator bristles.

1 Cover

2 Lock

3 Brush roller



Press the closure to the side and swivel 

the cover upwards.



Pull out the brush rollers.



Insert and lock into place the new brush 

rollers.



Rotate the brush rollers so that the 

mark at the end is in a vertical position.



Swivel the cover down and secure with 

the closures.

1 Drive shaft

2 Pin

3 Side brushes

4 Spring pin

Vacuuming completed

Shutting down

Replacing the filter bag

Transport Storage Maintenance and care

Maintenance schedule

Prior to operation:

After operation:

Every 50 operating hours

Every 100 operating hours

Every 200 operating hours

Maintenance contract

Remove the coarse dirt pan

Replacing the brush rollers

Replacing the side-brushes

16 EN