Karcher CV 60-2 RS Bp Pack: Faults

     - 

6



Pull out the spring plug.



Pull out the pin.



Remove the side brush.



Install new brush in reverse sequence. 

If the chain can be moved more than 6 mm 

to each side, it must be retensioned.



Remove the bottom front panels.



Loosen the 5 fastening screws of the 

gear motor.



Slide the gear motor up until the chain 

tension is correct.



Tighten the screws.



Danger

Risk of injury! Before carrying out any tasks 

on the machine, set the main key to "0" and 

remove it.  Pull out the battery plug.

Note

Suction turbine will continue to run for a 

while after switch-off. Carry out mainte-

nance tasks only after the suction turbine 

has come to a halt.

In case of faults that cannot be remedied 

using the table below please contact the 

customer service. 

A blinking battery display indicates the fol-

lowing faults. The time sequence of the 

blinking segments indicates the type of 

fault.



Before restarting the charger, pull the 

plug out of the socket, wait until the 

charge status indicator shuts off and 

plug the mains plug back in.

Adjust the chain tension of the trav-

el drive.

Faults

Errors shown by the battery indicator

Number of flashes Fault

Remedy

1

Battery discharged oder battery cable damaged.

Check battery cable, charge battery.

2

Cable to drive motor interrupted.

Inform Customer Service

3

Cable to drive motor shorted.

4

Deep discharge power not reached

Charge battery.

5

--

--

6

Drive attempt while charger is connected.

Remove the power plug from the charger and hook the 

holder into the appliance.

7

Fault in drive pedal.

Release the drive pedal prior to turning on the appliance.

8

Control faulty.

Inform Customer Service

9

Parking brake fault.

10

Shorted connection on battery connection.

Check the terminals on the batteries.

Once every 5 sec-

onds

Control idle.

Turn the main switch to "0" and turn it back to "1". 

Faults shown by the charge status indicator (Bp model only)

Blinking signal

Fault

Remedy

Blinks red

Battery poled or is not connected

Check battery cable for correct sitting.

Blinks green and 

yellow.

Cable connection between battery and charger is 

poor.

Check battery cable for correct sitting.

Check whether the connection to the battery was interrupt-

ed during the charge process.

Battery defective

Check battery. 

17 EN

- 

7

Faults

Fault

Remedy

By whom

Appliance cannot be started

Insert the battery plug on the device.

Operator

Swivel the top of the appliance down and close the lock.

Operator

Release emergency-stop button by turning.

Operator

Check battery cable for correct sitting.

Operator

Check battery cable for corrosion; clean, if required.

Operator

Battery capacity exhausted; recharge battery.

Operator

Remove the power plug from the charger and hook the holder into the appliance.

Operator

Device does not drive or drives 

only slowly

Release accelerator pedal, turn the key switch to "0", turn the key switch to "1", press 

the accelerator pedal.

Operator

Reset the fuse.

Operator

Set the unlock lever to "drive".

Operator

Charge battery.

Operator

Motor or control overheated; switch off the appliance and let it cool down for 5 minutes. Operator

Remove obstacles from the wheels or push the appliance away from the obstacle.

Operator

Device does not brake

Park brake deactivated; pull the unlock lever down to activate.

Operator

No or inadequate suction power Reset fuse of suction turbine.

Operator

Clean the seals between the dirt container and the top of the appliance and check for 

leaks, replace if required.

Operator

Swivel the top of the appliance down and close the lock.

Operator

Carefully insert the suction pipe into the holder.

Operator

Filter bag full; replace filter bag. 

Operator

Charge battery.

Operator

Check suction hose for blockages; clean if required.

Operator

Check the suction hose for tightness; replace if required.

Operator

The battery indicator blinks

Charge battery.

Operator

See "Faults with display".

Operator

Brushes do not turn or turn too 

slowly

Reset fuse of brush drive.

Check side brush fuse (F4), replace if required.

Operator

Check the brush for blockage by foreign objects; remove the foreign objects.

Operator

The status indicator of the filter bag illuminates red: Replace the filter bag, empty the 

coarse dirt pan.

Operator

Charge battery.

Operator

The cleaning head is not low-

ered.

Reset the fuse for the lift unit of the brush/suction head.

Operator

18 EN