Karcher HDS-C 7-11 Stahl lackiert: EC Declaration of Conformity

- 

13



Locate the local water hardness in the 

diagram. 



Extend the vertical line upward until the 

curve for the corresponding point has 

been reached. 



Draw a horizontal line from the intersec-

tion and read the setting value (A). 



Adjust the speed potentiometer in the 

switching cabinet to the value that you 

have ascertained (A). 

Example: For a water hardness of 18 °dH 

on the scale for the SB-HDS 9/15, set the 

speed potentiometer to position 5.5.  This 

results in a pause of 27 seconds, i.e. the 

solenoid valve will open briefly every 27 

seconds. 



Close the switching cabinet.



Oil level has to be between MIN and 

MAX.



Cut off the top of the oil container.

It is proposed to use the detergent contain-

er without cover. During transport, the con-

tainer can be closed using the delivered lid.

If the container should be kept closed dur-

ing operations, then make a hole of 25mm 

diameter in the lid.



Open the detergent container and fill in 

detergent.



Only HDS-C 7/11, HDS-C 9/15: Open 

the fuel tank and fill in fuel.

1 Dosing container



Remove the cover of the dosing con-

tainer and fill in RM 110.



Close the lid again.



Set main switch to “1”.



Select cleaning programme 3. 



Set the switch for continuous opera-

tions/ coin verifier to continuous opera-

tions.



Check burner setting.  Rectify the burn-

er settings if the measured values devi-

ate from the values given below. 

Note

On finishing checking, close the door of the 

plant and check the burner function when 

the entire plant is closed.  If the burner ex-

tinguishes due to lack of air, you can take 

the following steps:



Remove the stopper from the floor of 

the plant. 



Partially remove the sealing on the door 

sides. Also reduce the sealing starting 

from the bottom until 20 to 30 cm.



Set the continous operation/ coin verifi-

er switch to coin verifier (only for ABS 

Münzprüfer).

We hereby declare that the machine de-

scribed below complies with the relevant 

basic safety and health requirements of the 

EU Directives, both in its basic design and 

construction as well as in the version put 

into circulation by us. This declaration shall 

cease to be valid if the machine is modified 

without our prior approval.

The undersigned act on behalf and under 

the power of attorney of the company man-

agement.

Authorised Documentation Representative

S. Reiser

Alfred Kärcher GmbH Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Phone: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2011/05/01

Ceck the oil level

Preparing the detergent container

Filling in detergents

Fill in hardening liquid

Initial start-up HDS-C 7/11, HDS-C 9/

15

HDS-C 7/

11

HDS-C 9/

15

Fuel pressure, 

approx. 

1,1 MPa 

(11 bar)

1,1 MPa 

(11 bar)

Blower pres-

sure, approx. 

2,5 hPa 

(2,5 mbar)

4,0 hPa 

(4,0 mbar)

CO

2

10...11%

10...11%

Emission tem-

perature

160...180 

°C

180...200 

°C

Emission loss

max. 9%

max. 9%

Soot values

max. 1

max. 1

EC Declaration of Conformity

Product:

High-pressure cleaner

Type:

1.319-xxx

Relevant EU Directives

2006/42/EC (+2009/127/EC) 

2004/108/EC

2000/14/EC

Applied harmonized standards

EN 60335–1

EN 60335–2–79

EN 55014–1: 2006 + A1: 2009

EN 55014–2: 1997 + A2: 2008

EN 61000–3–11: 2000

EN 61000–3–12: 2005

EN 62233: 2008

Applied conformity evaluation method

2000/14/EC: Appendix V

Sound power level dB(A)

HDS-C 7/11

Measured:

70

Guaranteed: 71

HDS-C 8/15

Measured:

70

Guaranteed: 71

HDS-C 9/15

Measured:

87

Guaranteed: 88

CEO

Head of Approbation

29 EN