Electrolux EWC1350: Before first use
Before first use: Electrolux EWC1350
electrolux 7
gramme or to select «Rinse hold» or «No
= Washing, = Rinses, = Spin,
spin»option.
= Cycle End, = Door Locked
Programme Selector Dial
= Rinse Hold, = No Spin, = Cot-
It allows you to switch the appliance on/off
ton,
= Synthetic, = Delicate, =
and/or to select a programme.
Handwash,
= Wool, 30 ° = Mini 30 ° ,
Table of Symbols
=Drain, =Cold, = ON/OFF
= Delay Start, = Prewash, =
Quick,
= Super Rinse, = Start/Pause
Before first use
Warning!
any residues which may have been left by the
manufacturing process. Pour approx. 100 ml
Ensure that the electrical and water connec-
of detergent straight into the drum and run a
tions comply with the installation instructions.
cotton cycle at 60°C. When the programme
is finished the machine will be ready to use.
Important! Remove any material from the
drum.
Important! We recommend you to run a
wash programme without any load, to clear
Daily use
Load the laundry
Open the door by carefully pulling the door
handle outwards. Place the laundry in the
drum, one item at a time, shaking them out
as much as possible. Close the door.
If required, pour fabric softener into the small-
er compartment marked
(the amount
used must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
Measure out the detergent and the
fabric softener
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent re-
quired, pour it into the larger compartment
on the left
.
8 electrolux
from creasing. When the programme has fin-
ished, the lights "End" and "Door locked" are
lit to indicate that the water must be emptied
out (See: " At the end of the programme").
No spin
By selecting this option all the spinning pha-
ses are excluded. To be used for extremely
delicate material. The machine will add some
additional rinses to the cotton and synthetic
programmes.
For the maximum spin speed allowed by
each programme, refer to the chapter
Washing programmes .
Select the Delay Start by pressing
Select the required programme by
button 2
means of the programme selector dial
Before you start the programme, if you wish
(9)
to delay the start, press the button 2 repeat-
Turn the programme selector dial to the re-
edly, to select the desired delay. The corre-
quired programme. The selector can be
sponding pilot light will light up.
turned either clockwise or anticlockwise.
The green light of button 6 starts to flash
On programme progress display the pilot
lights corresponding to all phases compos-
ing the selected programme are lit.
On position
the programme is reset and
the machine is switched OFF.
At the end of the programme the selec-
tor dial must be turned to position
to
switch the machine off.
You must select this option after you have set
Important! If you turn the programme
the programme and before you press button
selector dial to another programme when the
6 .
machine is working, the lights in the
You can cancel or modify the delay time at
programme progress display will start to
any moment, before you press button 6 .
flash to indicate a wrong selection. The
Cancelling the delayed start after having
machine will not perform the new selected
pressed button 6 :
programme.
1. Set the washing machine to PAUSE by
pressing button 6 .
Select the spin speed, Rinse Hold or No
2. Press the button 2 once, the light relevant
spin option (8)
to the selected delay goes off.
Select the spin speed, Rinse Hold option or
3.
Press button 6 again to start the pro-
No Spin option by turning the spin speed se-
gramme.
lector.
• The position 1300 (or 1000) is equivalent
Important! The selected delay can be
to 900 rpm for the synthetic and wool pro-
changed only after selecting the washing
grammes and 700 rpm for the delicate
programme again.
wash programme.
The door will be locked throughout the delay
• The position 500 is equivalent to 500 rpm
time (door locked light lit).
for the synthetic and wool programmes
The Delay Start can not be selected with
and 450 rpm for the delicate wash pro-
DRAIN or SPIN programme.
gramme.
Rinse hold
By selecting this option the water of the last
rinse is not emptied out to prevent the fabrics
electrolux 9
Select the desired option by means of
Cancelling a programme
buttons 3, 4 and 5
Turn the selector dial to
position to cancel
Depending on the programme, different
a programme which is running. Now you can
functions can be combined. These must be
select a new programme.
selected after choosing the desired pro-
Opening the door after the programme
gramme and before pressing the button 6.
has started
The relevant light will illuminate.
First set the machine to pause by pressing
the button 6 .
After some minutes, the door can be
opened, when the following conditions are
observed:
• The water temperature is below 55°C.
• The water level is below the bottom edge
of the door.
• The machine doesn’t spin.
If you cannot open the door but it is abso-
If an incorrect option is selected, the corre-
lutely necessary to open it you have to switch
sponding indicator lamp flashes for about 2
the machine off by turning the selector dial to
seconds. For the compatibility of the options
. After few minutes the door can be
with the washing programmes, refer to the
opened
chapter «Washing programmes» .
(Pay attention to the water level and
temperature!).
Start the programme by pressing button
After this procedure, it will be necessary to
6
set the programme and the options again
To start the selected programme, press this
and then press the button 6 .
button; the corresponding pilot light stops
At the end of the programme
flashing and remains lit.
On programme progress display the pilot
The machine stops automatically.
lights A and E illuminate to indicate that the
The pilot light D illuminates to indicate that
appliance starts operating and the door is
the programme has finished. The pilot light
locked.
E goes out, the door can be opened and the
laundry can be removed.
Altering an option or a running
If at the end of a programme there is water in
programme
the tub (when "Rinse hold" option has been
It is possible to change any option before the
selected), to empty out the water follow
programme carries it out.
the following instructions :
Before you make any change, you must
•
turn the programme selector dial to
pause the washing machine by pressing the
• select the «Drain» or «Spin» programme
button 6 .
•press button 6
The programme can be changed as long as
When the pilot light E goes out, the door can
the button 6 has not been pressed. Changing
be opened and the laundry can be removed.
a running programme is possible only by re-
At the end of the cycle, turn the programme
setting it. Turn the programme selector dial
selector dial to
to switch the machine off.
to
and then to the new programme posi-
Remove the laundry from the drum and care-
tion. Start the new programme by pressing
fully check that the drum is empty. If you do
the button 6 again.
not intend to carry out another wash, close
Interrupting a programme
the water tap.
Leave the door open to prevent the formation
Press the button 6 to interrupt a programme
of mildew and unpleasant smells.
which is running, the corresponding light
starts to flash. Press the button again to re-
start the programme.
Оглавление
- EWC 1050 EWC 1350
- Electrolux. Thinking of you.
- Product description
- Control panel
- Before first use
- Helpful hints and tips
- Washing programmes
- Care and cleaning
- What to do if…
- Technical data
- Installation
- Environment concerns
- Electrolux. Thinking of you.
- Описание изделия
- Панель управления
- Перед первым использованием
- Полезные советы
- Программы мойки
- Уход и чистка
- Что делать, если ...
- Технические данные
- Установка
- Охрана окружающей среды
- Electrolux. Thinking of you.
- Descripción del producto
- Panel de mandos
- Antes del primer uso
- Consejos útiles
- Programas de lavado
- Mantenimiento y limpieza
- Qué hacer si…
- Datos técnicos
- Instalación
- Aspectos medioambientales