Zanussi FE 1014 N: инструкция
Раздел: Бытовая, кухонная техника, электроника и оборудование
Тип: Стиральная Машина
Инструкция к Стиральной Машине Zanussi FE 1014 N
WASHING MACHINE
TVÄTTMASKIN
PYYKINPESUKONE
STIRALWNAÅ MAfiINA
FE 1014 N
GB
USER MANUAL
S
BRUKSANVISNING
FIN
KÄYTTÖOHJE
RUS
132996790
RUKOVODSTVO PO ÈKSPLUATACII
Dear customer,
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
Transport damages
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is
particularly important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use
of the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
Our contribution to the protection of the
environment: we use recycled paper.
2
Contents
Warnings 4-5
Maintenance 20
Door seal 20
Disposal 5
Bodywork 20
ENGLISH
Detergent dispenser drawer 20
Tips for environmental protection 5
Drain filter 20
Water inlet filter 21
Technical specifications 6
Emergency emptying out 21
The dangers of freezing 21
Installation 7
Unpacking 7
Something not working? 22-23
Positioning 7
Water inlet 7
Water drainage 8
Electrical connection 8
Your new washing machine 9
Description of the appliance 9
Door locked pilot light 9
Detergent dispenser drawer 9
Use 10
Control panel 10
Controls 10-12
Washing hints 13
Sorting the laundry 13
Temperatures 13
Before loading the laundry 13
Maximum loads 13
Laundry weights 13
Removing stains 13
Detergents and additives 14
International wash code symbols 15
Operating sequence 16-18
Programme Chart 19
3
Warnings
The following warnings are provided in the interests of overall safety. You must read them carefully before
installing or using the appliance.
Installation
• Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
• All internal packing must be removed before using
seal and prevents the formation of musty smells.
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
• Always check that water has emptied out before
transit devices are not removed or are not
opening the door. If not, drain the water following
completely removed. Refer to the relevant
the instructions in the instruction book.
paragraph in the instruction book.
• Always unplug the appliance and shut the water
• Any electrical work required to install this
tap after use.
appliance must be carried out by a qualified
electrician.
General safety
• Any plumbing work required to install this
appliance must be carried out by a qualified
• Repairs to the machine must be carried out only
plumber.
by qualified personnel. Repairs carried out by
inexperienced persons could cause serious
• After having installed the machine, check that it is
danger. Contact your local Service Centre.
not standing on its electrical supply cable.
• Never pull the power supply cable to remove the
• If the appliance is placed on a carpeted floor,
plug from the socket; always take hold of the plug
ensure that air can circulate freely between the
itself.
feet and the floor.
• During high temperature wash programmes the
door glass may get hot. Do not touch it!
Use
• This appliance is designed for domestic use. It
must not be used for purposes other than those
for which it was designed.
• Only wash fabrics which are designed to be
machine washed. Follow the instructions on each
garment label.
• Do not overload the appliance. Follow the
instructions in the instruction book.
• Make sure that all pockets are empty. Objects
such as coins, safety pins, pins and screws can
cause extensive damage.
• Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing
garments in the appliance.
• Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
• Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
4
Child safety
• Children are often not aware of how dangerous
• Make sure that children or pets do not climb into
electrical appliances can be. When the machine is
the drum.
ENGLISH
working, children should be carefully supervised
• When the appliance is to be scrapped, cut off the
and not be allowed to play with the appliance.
electrical supply cable and destroy the plug with
• The packaging components (e.g. plastic film,
the remaining cable. Disable the door catch in
polystyrene) can be dangerous to children -
order to prevent children from becoming trapped
danger of suffocation! Keep them out of children’s
inside while playing.
reach.
• Keep all detergents in a safe place out of
children’s reach.
Disposal
Packaging materials
Machine
The materials marked with the symbol are
Use authorised disposal sites for your old appliance.
recyclable.
Help to keep your country tidy!
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing
of them properly in appropriate collection
containers.
Tips for environmental protection
To save water, energy and to help protect the
• With adequate pre-treatment, stains and limited
environment, we recommend that you follow these
soiling can be removed; the laundry can then be
tips:
washed at a lower temperature, so saving energy.
• Normally soiled laundry may be washed without
• Measure out detergent according to the water
prewashing in order to save detergent, water and
hardness, the degree of soiling and the quantity of
time (the environment is protected too!).
laundry being washed.
• The machine works more economically if it is fully
loaded, but do not overload it (see maximum load
on page 19).
5
Technical specifications
DIMENSIONS Height 85 cm
Width 60 cm
Depth 45 cm
WASH LOAD Cotton 4 kg (max. 4.5 kg)
Synthetics 1.5 kg
Delicates 1.5 kg
Woollens 1 kg
SPIN SPEED 1000 rpm max.
POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz
TOTAL POWER ABSORBED 2200 W
MINIMUM FUSE PROTECTION 10 A
WATER PRESSURE Minimum 50 kPa
Maximum 800 kPa
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
6
Installation
Unpacking
All transit bolts and packing must be
ENGLISH
removed before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the rear
right-hand bolt and lay the machine on its back,
taking care not to squash the hoses. This can be
avoided by placing one of the corner packing
pieces between the machine and the floor.
2. Remove the polystyrene block from the bottom
of the machine and release the two plastic bags.
3. Carefully remove the right-hand bag (1) then the
left-hand bag (2) by pulling them towards the
centre of the machine.
4. Set the machine upright and remove the two
remaining bolts from the back.
5. Pull out the three plastic spacers from the holes
into which the bolts were fitted.
6. Plug all the holes with the plugs which you will
find in the envelope containing the instruction
booklet.
7
P0020
P0256
2
1
P1066
P1068
P0255
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Carefully level by screwing the adjustable feet in or
out. Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor.
Water inlet
Connect the water inlet hose supplied with the
machine to a tap with a 3/4" thread.
Do not use already employed hoses.
The other end of the inlet hose which connects to
the machine can be turned in any direction. Simply
loosen the fitting, rotate the hose and retighten the
fitting, making sure there are no water leaks.
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
P0021
P1088
P1051
Water drainage
The end of the drain hose can be positioned in three
ways:
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
This could be done by tying it to the tap with a piece
of string or attaching it to the wall.
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain pipe
must be larger than the outside diameter of the drain
hose.
The drain hose must not be kinked. Run it along the
floor; only the part near the drainage point must be
raised.
8
P0023
P0022
Electrical connection
This machine is designed to operate on a 220-230
V, single-phase, 50 Hz supply.
Check that your domestic electrical installation can
take the maximum load required (2.2 kW), also
taking into account any other appliances in use.
Connect the machine to an earthed socket.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable
need to be replaced, this should be carried
out by our Service Centre.
Please ensure that when the appliance is
installed the power supply cable is easily
accessible.
Your new washing machine
This new washing machine meets all modern needs for effective treatment of laundry with low water, energy
and detergent consumption.
• The possibility of selecting the temperature, spin speed and all the options offered by this washing machine
ENGLISH
gives you truly “customised” washing.
• The programme progress display shows the programme steps selected and the programme phase which
is running.
• The special wool programme with its new delicate wash system treats your woollens with extreme care.
• The balance control device ensures the machine is stable during the spin.
Description of the appliance
1 Detergent dispenser drawer
2 Control panel
3 Door locked pilot light
4 Drain filter
5 Adjustable feet
Door locked pilot light
It stays on during the whole programme indicating
that the door is locked.
When the light goes out, the door can be opened
(see page 18).
Detergent dispenser drawer
Prewash
Main wash
Fabric softener, starch
9
1 2
FLN 1009
ALGODON
SINTETICO
90°C
60°C
1000
800
PRELAVADO
M
R
A
H
C
/
A
A
P
R
A
ACLARADO
D
A
DELICADOS
LANA
30°C
40°C
600
FRIO
400
AGUA EN
ADICIONAL
LA CUBA
LAVADO
RAPIDO
ESPEC.
PROGR.
T
J
E
D
I
O
S
T
M
E
P
R
E
A
R
U
T
A
E
C
N
R
T
I
F
U
G
D
A
O
O
P
C
I
O
N
E
S
S
T
R
A
/
T
P
A
S
U
A
N
A
U
L
.
3
4
5
C0069
Use
10
FE 1014 N
COTTONS
95°C
1000
PREWASH
SYNTHETICS
60°C
900
SUPER
DELICATES
40°C
700
RINSE
O
N
/
O
F
F
WOOL
30°C
500
SKIP
RINSE
COLD
QUICK
HOLD
T
E
S
T
E
S
M
S
A
E
R
E
T
E
D
O
R
T
/
P
A
U
S
F
A
S
P
E
R
A
T
U
R
P
I
N
S
P
E
E
P
T
B
R
I
I
O
N
S
C
1 23 456 789
Control panel
Important!
1 ON/OFF button
By depressing TEMPERATURE and SPIN SPEED
Press this button to switch the washing machine on.
buttons simultaneously, the acoustic signal at the
Press the ON/OFF button again to switch the
end of the cycle is suppressed.
machine off.
5 SPIN SPEED button
2 MAINS-ON light
Press this button repeatedly to change the spin
This light is connected to the ON/OFF button. It
speed, if you want your laundry to be spun at a
lights up when you press the button, and goes out
speed different from the one proposed by the
when you press it again.
washing machine. The relevant light will light up.
Maximum speeds are:
• for cotton: 1,000 rpm
3 FABRIC button
• for synthetic fabrics and wool 900 rpm;
Press this button repeatedly to select the programme
• for delicate fabrics: 700 rpm.
on the basis of the type of laundry to be washed. The
RINSE HOLD position: when you choose this
light relevant to the selected programme will light up.
option, the machine will not drain the water of the
The washing machine will propose a temperature and
last rinse, so as not to wrinkle the laundry.
automatically select the maximum spin value
At the end of the cycle, the light of the
provided for the programme you have chosen. You
START/PAUSE button will flash, to indicate that the
can change these values by operating buttons 4 and
water must be drained.
5.
To complete the cycle, choose one of the following
options:
4 TEMPERATURE button
• Draining and spin:
- Press the START/PAUSE button. The machine
Press this button repeatedly to increase or decrease
will drain the water, then spin the laundry at the
the temperature, if you want your laundry to be washed
maximum speed provided for the selected
at a temperature different from the one proposed by
programme.
the washing machine. The relevant light will light up.
- Select spin speed by means of button 5, and
Maximum temperatures are 95°C for cotton, 60°C for
press the START/PAUSE button.
synthetic fabrics, 40°C for delicate fabrics and wool.
• Drain only
By selecting position COLD the machine will wash with
- Press the RESET button once, so as to cause
cold water. To be used for extremely delicate items,
the DRAIN light to light up, then press the
such as curtains.
START/PAUSE button.
Important! If you accidentally press the RESET
7 START/PAUSE button
button more than once, the programme is
This button has three functions:
cancelled. To cause the washing machine to
• Start: after you have selected the desired
drain the water, select any washing programme
ENGLISH
programme and options, press this button to start
by means of the FABRIC button, then press
the washing machine. The light above the button
RESET three times in order to select the DRAIN
will stop flashing and remain lit.
position (only the DRAIN light will remain
lit).
• Pause: when you press this button again, the
programme in progress is interrupted. The light
above the button will start flashing. To restart the
6 OPTIONS button
programme, press the button again.
Press this button to select the following options:
When you PAUSE the cycle, the DOOR LOCKED
• PREWASH: select this option if you wish your
light goes out, and it becomes possible to open
laundry to be prewashed before the main wash
the door, provided
(not available for wool).
• the washing machine is not in the heating phase;
The prewash ends with a short spin in
• the level of the water is not high;
programmes for cotton and synthetic fabrics,
• the drum is not turning.
whereas in the programme for delicate fabrics the
Important! You must set the washing machine to
water is only drained.
PAUSE before you make any change in the
• SUPER RINSE: this option can be selected with
programme in progress.
all programmes except the wool programme.
• Draining of water and spinning after the
The machine performs 4 rinses instead of 3. This
execution of programmes with the RINSE HOLD
option is recommended for people who are
option.
allergic to detergents, and in areas where the
water is very soft.
• QUICK WASH: to be used for lightly soiled
8 SKIP/RESET button
laundry (not for wool).
At the end of a programme, you must press this
The washing time will be reduced according to the
button once or repeatedly, in order to clear the
type of fabric and the selected temperature.
contents of the memory; otherwise, the next time
Important: PREWASH and SUPER RINSE can be
you switch the washing machine on, the audible
selected together. Press the button until both lights
warning signals relevant to the end of the previous
light up.
cycle will be given.
You can also press the RESET button to exclude
one or several phases of the programme which is
running, as indicated below.
- set the washing machine to PAUSE by pressing
the START/PAUSE button (the relevant light will
flash);
- press the RESET button once or several
times, until the required phase(s) is(are) cancelled
(the light next to the name of the phase(s) will go out).
11
Example:
9 Programme phase indicator
In this case, the spin
lights
(at the speed provided
for the selected type of
When you select a programme, the lights relevant to
fabric) will be
the phases that form the programme light up.
performed.
This button allows you also to select special
programmes, such as RINSES, SPIN and DRAIN.
• If the machine is already switched on because it
After you have started the programme, only the light
has just performed a washing programme, proceed
relevant to the phase that is currently being carried
as follows:
out will remain lit.
- depress RESET once or repeatidly to cancel the
At the end of the programme the pilot light
previously performed programme (all the phase
illuminates.
indicator lights must be off);
If the light lights up at the end of the programme
- select the type of fabric by means of the relevant
this means that the drain filter is clogged.
button;
The END pilot light flashes in the event of
- select the special programme:
operating problems.
• RINSES AND SPIN
At the same time one of the following lights starts to
Depress RESET once, the pilot light (WASH)
flash:
goes out.
= the machine does not fill
• SPIN
= the machine does not empty
Depress RESET twice, the pilot lights WASH
= the door has not been closed
and RINSES go out.
To eliminate the problem, see paragraph
• DRAIN
“Something not working”.
Depress RESET three times, the pilot lights
WASH , RINSES and SPIN go out.
Example:
In this case the
machine will perform
the rinses and spin.
• If the machine is switched off:
- depress ON/OFF button to switch it on;
- select the type of fabric by means of the relevant
button:
- select the special programme as previously
described.
PREWASH
WASH
RINSES
RINSE HOLD
SPIN
DRAIN
FILTER
END
12
Laundry weights
Washing hints
The following weights are indicative:
bathrobe 1200 g
ENGLISH
Sorting the laundry
napkin 100 g
Follow the wash code symbols on each garment
quilt cover 700 g
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
sheet 500 g
whites, coloureds, synthetics, delicates, woollens.
pillow case 200 g
tablecloth 250 g
Temperatures
towelling towel 200 g
90° for normally soiled white cottons and linen
tea cloth 100 g
(e.g. tea cloths, towels, tablecloths,
night dress 200 g
sheets...)
ladies’ briefs 100 g
60° for normally soiled, colour fast garments
man’s work shirt 600 g
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
man’s shirt 200 g
lightly soiled white cotton (e.g.
man’s pyjamas 500 g
underwear).
blouse 100 g
cold for delicate items (e.g. net curtains),
men’s underpants 100 g
30°-40° mixed laundry including synthetic fibres
and woollens.
Removing stains
Before loading the laundry
Stubborn stains may not be removed by just water
Never wash whites and coloureds together. Whites
and detergent. It is therefore advisable to treat them
may lose their “whiteness” in the wash.
prior to washing.
New coloured items may run in the first wash; they
Blood: treat fresh stains with cold water. For dried
should therefore be washed separately the first time.
stains, soak overnight in water with a special
detergent then rub in the soap and water.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
Button up pillowcases, close zip fasteners, hooks
stain; treat several times.
and poppers. Tie any belts or long tapes.
Dried grease stains: moisten with turpentine, lay
Remove persistent stains before washing. Rub
the garment on a soft surface and dab the stain with
particularly soiled areas with a special detergent or
the fingertips and a cotton cloth.
detergent paste.
Rust: oxalic acid dissolved in hot water or a rust
Treat curtains with special care. Remove hooks or
removing product used cold. Be careful with rust
tie them up in a bag or net.
stains which are not recent since the cellulose
structure will already have been damaged and the
Maximum loads
fabric tends to hole.
Recommended loads are indicated in the
Mould stains: treat with bleach, rinse well (whites
programme charts.
and fast coloureds only).
General rules:
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Cotton, linen: drum full but not too tightly packed;
Ball point pen and glue: moisten with acetone (*),
Synthetics: drum no more than half full;
lay the garment on a soft cloth and dab the stain.
Delicate fabrics and woollens: drum no more than
Lipstick: moisten with acetone as above, then treat
one third full.
stains with methylated spirits. Remove any residual
Washing a maximum load makes the most efficient
marks from white fabrics with bleach.
use of water and energy.
Red wine: soak in water and detergent, rinse and
For heavily soiled laundry, reduce the load size.
treat with acetic or citric acid, then rinse. Treat any
residual marks with bleach.
13
Ink: depending on the type of ink, moisten the fabric
Quantity of detergent to be used
first with acetone (*), then with acetic acid; treat any
The type and quantity of detergent will depend on
residual marks on white fabrics with bleach and then
the type of fabric, load size, degree of soiling and
rinse thoroughly.
hardness of the water used.
Tar stains: first treat with stain remover, methylated
Water hardness is classified in so-called “degrees”
spirits or benzine, then rub with detergent paste.
of hardness. Information on hardness of the water in
(*) do not use acetone on artificial silk.
your area can be obtained from the relevant water
supply company, or from your local authority.
Detergents and additives
Follow the product manufacturers’ instructions on
quantities to use.
Good washing results also depend on the choice of
Use less detergent if:
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
– you are washing a small load,
biodegradable, detergents contain substances
– the laundry is lightly soiled,
which, in large quantities, can upset the delicate
– large amounts of foam form during washing.
balance of nature.
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
Degrees of water hardness
washing temperature and degree of soiling.
All commonly available washing machine detergents
Degrees
may be used in this appliance:
Level
Characteristic
– powder detergents for all types of fabric,
German
French
– powder detergents for delicate fabrics (60°C max)
°dH
°T.H.
and woollens,
– liquid detergents, preferably for low temperature
1
soft
0- 7
0-15
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
2
medium
8-14
16-25
The detergent and any additives must be placed in
3
hard
15-21
26-37
the appropriate compartments of the dispenser
drawer before starting the wash programme.
4
very hard
more
more
If using concentrated powder or liquid detergents, a
than 21
than 37
programme without prewash must be selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked before
starting the wash programme.
Follow the product manufacturer’s
recommendations on quantities to use and do not
exceed the «MAX» mark in the detergent
dispenser drawer.
14
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
ENGLISH
Energetic wash
Max. wash
Max. wash
Max. wash
Max. wash
temperature
temperature
temperature
temperature
95°C
60°C
40°C
30°C
Hand wash Do not
Delicate wash
wash
at all
Bleaching Bleach in cold water Do not bleach
Ironing Hot iron
Warm iron
Lukewarm iron
Do not iron
max 200°C
max 150°C
max 110°C
Dry cleaning Dry cleaning
Dry cleaning in
Dry cleaning
Do not
in all solvents
perchlorethylene,
in petrol,
dry clean
petrol, pure alcohol,
pure alcohol
R 111 & R 113
and R 113
high
temperature
low
temperature
Drying Flat On the line On clothes
Tumble dry
Do not
hanger
tumble dry
15
95
60
60
40
40
40
30
30
4. Switch the machine on
To switch the machine on, press the ON/OFF button
: the mains-on light comes on.
5. Select the desired programme/
fabric
Press the FABRIC button repeatedly, in order to
select the desired programme/fabric. The relevant
light will light up.
The lights relevant to the phases that form the
programme will light up.
The START/PAUSE button light will start flashing.
6. Select the temperature
Press the TEMPERATURE button if you wish to
select a temperature value different from the one
proposed by the washing machine.
The relevant light will light up.
95°C
60°C
40°C
30°C
COLD
T
E
E
M
R
P
E
R
A
T
U
COTTONS
SYNTHETICS
DELICATES
WOOL
F
A
B
R
I
C
S
O
N
/
O
F
F
Operating sequence
Before washing your first load of laundry, we
recommend that you run a cotton cycle at 60°C,
with the machine empty, in order to remove any
manufacturing residue from the drum and tub.
Pour half a measure of detergent into the main wash
compartment and start up the machine.
1. Place the laundry in the drum
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
2. Measure out the detergent
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment .
If you wish to carry out the prewash, pour detergent
into the appropriate compartment marked .
3. Measure out the additives
If required, pour fabric softener into the
compartment marked without exceeding the
«MAX» mark.
C0071
C0070
P0004
16
9. Start the programme
Press the START/PAUSE button. The relevant light
will stop flashing, the DOOR LOCKED light will light
ENGLISH
up, and only the light relevant to the phase that is in
progress will remain lit.
10. How to change a programme
during its cycle
Before you make any change, you must pause the
washing machine by pressing the START/PAUSE
button.
It is possible to change any phase before the
programme carries it out.
Changing the type of fabric or temperature is
possible, obviously, only during the washing phase.
When you make a change in these two parameters,
the washing machine will resume the cycle from the
beginning.
If it is necessary to drain the water in order to
change the programme in progress, proceed as
follows:
• PAUSE the machine by pressing the
START/PAUSE button;
• press the RESET button repeatedly, until
only the DRAIN light remains lit;
• press the START/PAUSE button again.
When the water has been drained, you may select a
new programme and press the START/PAUSE
button to start it.
17
S
T
A
R
T
/
P
A
U
S
E
7. Select the spin speed or the
RINSE HOLD option
Press the SPIN SPEED button repeatedly, in order
to select the desired spin speed or the RINSE HOLD
option. The relevant light will light up.
If you select the RINSE HOLD option, the machine
will stop at the end of the programme with the water
still in the tub.
8. Select the desired options
If your laundry is very dirty, it may be advisable to
select the PREWASH option.
If you wish the laundry to undergo an extra rinse,
select the SUPER RINSE option.
Press the OPTIONS button so as to cause one or
both of the lights to light up.
Select the QUICK WASH option, if your laundry is
only slightly soiled. The relevant light illuminates.
P
R
EW
A
S
H
S
U
P
ER
R
I
NS
E
Q
U
IC
K
O
P
T
I
O
N
S
1000
900
700
500
RINSE
HOLD
S
P
I
N
S
P
E
E
D
11. How to cancel a programme
13. End of programme
during its cycle
At the end of the programme, the washing machine
stops automatically and gives an audible signal.
To cancel a programme that is being carried out,
first pause the washing machine by pressing the
If you had selected the RINSE HOLD option, the
START/PAUSE button, then press the RESET button
light of the START/PAUSE button flashes and the
repeatedly, until the phase indicator lights go out.
phase indicator light remains lit to indicate that the
water must be drained.
When the programme has been completed the
12. How to open the door during
audible signal is given.
the cycle of a programme
The DOOR LOCKED light goes out at once.
You can open the door, after having set the washing
Press the SKIP/RESET button repeatedly to
machine to PAUSE, provided the following
erase the programme that has just been carried
conditions exist:
out. If you omit to do this, the next time you
switch the washing machine on, you will hear the
• the washing machine is not in the heating phase
audible signal.
beyond 40°C;
Note: when you switch the machine on, if you must
• the level of the water is not high;
erase the previously performed programme, it is
• the drum is not turning.
also sufficient to press the FABRIC button and
If these requirements are met, when you pause the
select a new programme.
washing machine, the DOOR LOCKED light goes
Press the ON/OFF button to switch the machine off.
out and the door can be opened.
The relevant light will go out.
Should it not be possible to open the door, and
Remove the laundry from the washing machine.
should it be absolutely necessary to do so, switch
Check whether the drum is completely empty, by
the machine off by pressing the ON/OFF button.
rotating it with your hand. The purpose of this is to
After approximately 3 minutes, you can open the
prevent any items of laundry from remaining
door.
accidentally in the drum, where they might get
Pay attention to the level and temperature of the
damaged in a subsequent wash (e.g. by shrinking)
water in the washing machine!
or bleed colour into another load of laundry.
When you close the door and press the ON/OFF
We advise you to close the water supply tap and
button again, the washing machine will resume the
disconnect the plug from the socket.
programme from the point where it had been
Leave the door ajar in order to air the washing
interrupted.
machine.
18
Programme chart
Washing programmes
Type of
Consumption*
laundry and
Max.
Programme/
Description of
Available options
ENGLISH
symbols on
load
temperature
programme
Energy
Water
Time
labels
kWh
litres
h/min.
White cotton:
e.g. sheets,
tablecloths,
household
linen
**The “coloured cotton programme” at 60°C with a wash load of 4 kg is the reference programme for the data
entered in the energy
label, in compliance with EEC 92/75 standards.
* This data is given purely as an indication: the consumption values may vary in relation to the quantity and
type of laundry, the temperature of the water supply and the ambient temperature. The data refers to the
highest temperature provided for each programme. For cotton, it refers to a wash load of 4 kg.
19
95
60
SPIN SPEED
Wash at
RINSE HOLD
Cottons
60°-95°C
4.5 kg
PREWASH
1.75 51 140
60°-95°C
3 rinses
SUPER RINSE
Long spin
QUICK WASH
**
Coloured
cotton: e.g.
shirts,
blouses,
underwear,
towels,
household
linen
30
40
60
Wash at
SPIN SPEED
Cottons
60°-40°-30°C
RINSE HOLD
4.5 kg
60°-40°-30°C
or cold
PREWASH
0.90 48 130
COLD
3 rinses
SUPER RINSE
Long spin
QUICK WASH
Synthetic
fabrics and
blends: e.g.
shirts,
blouses,
underwear
30
40
60
Wash at
SPIN SPEED
Synthetics
60°-40°-30°C
RINSE HOLD
1.5 kg
60°-40°-30°C
or cold
PREWASH
0.7 47 85
COLD
3 rinses
SUPER RINSE
Short spin
QUICK WASH
Delicate fab-
rics: e.g.
acrylic
fabrics,
viscose, poly-
ester,
synthetic
blends
30
40
Wash at
SPIN SPEED
Delicates
40°-30°C
RINSE HOLD
1.5 kg
40°-30°C
or cold
PREWASH
0.5 48 55
COLD
3 rinses
SUPER RINSE
Short spin
QUICK WASH
Wool
30
40
Wash at
Wool
40°-30°C
SPIN SPEED
1 kg
40°-30°C
or cold
0.37 47 55
RINSE HOLD
COLD
3 rinses
Short spin
Maintenance
1. Door seal
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in
the fold.
2. Bodywork
Clean the outside of the machine with warm water
and a neutral, non-abrasive household detergent.
Rinse with clean water and dry with a soft cloth.
Important: do not use methylated spirits, solvents
or similar products to clean the bodywork.
3. Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it
under a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
To facilitate cleaning, the top part of the additive
compartments can be removed.
C0073
C0072
P1050
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
4. Drain filter
The drain filter collects threads and small objects
inadvertently left in the laundry. Check regularly that
the filter is clean.
Open the filter door.
Place a container under the filter to catch any
spillage.
Unscrew the filter and remove it.
Clean the filter under a running tap, then refit it,
screwing it fully in.
P0040
P0133
P0132
P0011
P0038
20
5. Water inlet filter
If you notice that the machine is taking longer to fill,
check that the filter in the water inlet hose is not
ENGLISH
blocked.
Turn off the water tap.
Unscrew the hose from the tap.
Clean the filter with a stiff brush.
Screw the hose back onto the tap.
6. Emergency emptying out
If the water is not discharged (outlet pump is
blocked, filter or drain pipe are clogged), proceed as
follows to empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• place a bowl on the floor;
• put the drain hose end into the bowl and let the
water come out.
Should it not be possible to have access to the drain
hose because, for example, the appliance is built in
the kitchen furniture, slightly loosen the drain filter
after placing a bowl on the floor, to let the water
come out slowly.
At the end screw the filter again.
21
P1090
The dangers of freezing
If the machine is exposed to temperatures below
0°C, certain precautions should be taken.
●
Turn off the water tap.
●
Unscrew the inlet hose.
●
Unhook the drain hose from the rear support and
position the end of this hose and that of the inlet
hose in a bowl. Run the draining programme.
To do this:
●
Switch the machine on
●
Select a washing programme
●
Press the RESET button three times
●
Press START/PAUSE button
●
Disconnect the appliance.
●
Screw the inlet hose and reposition the drain
hose.
●
When you intend to start the machine up again,
make sure that the room temperature is above
0°C.
Something not working?
Problems which you can resolve yourself.
During machine operation it is possible that the light , the light of the START/PAUSE button and one of
the following lights start to flash:
: problem with the water supply
: problem with water draining
: door open
Once the problem has been eliminated, press the START/PAUSE button to restart the programme. If after
all checks, the problem persists, contact your local Service Centre.
Problem Possible cause
• The door is not firmly closed.
• The machine does not start up:
• The machine is not plugged in or there is no power
at the socket.
• The main fuse has blown.
• The START/PAUSE button has not been
depressed.
• The water tap is closed.
• The machine does not fill:
• The inlet hose is squashed or kinked.
• The filter in the inlet hose is blocked.
• The door is not properly closed.
• The end of the drain hose is too low. Refer to
• The machine fills then empties
relevant paragraph in “water drainage” section.
immediately:
• The drain hose is squashed or kinked.
• The machine does not empty
• The RINSE HOLD option has been selected.
and/or does not spin:
• The drain filter is clogged.
• Too much detergent or unsuitable detergent
• There is water on the floor:
(creates too much foam) has been used.
• Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this
as the water runs down the hose; check to see if it
is damp.
• The drain hose is damaged.
• Too little detergent or unsuitable detergent has
• Unsatisfactory washing results:
been used.
• Stubborn stains have not been treated prior to
washing.
• The correct temperature was not selected.
• Excessive laundry load.
• The transit bolts and packing have not been
• The machine vibrates or is noisy:
removed.
• The support feet have not been adjusted.
• The laundry is not evenly distributed in the drum.
• Maybe there is very little laundry in the drum.
• The programme is still running, the drum is
• The door will not open:
turning.
• The door lock has not yet released.
• The water level is above the bottom edge of the door.
• The machine is heating the water.
22
ENGLISH
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and
purchase date of your machine: the Service Centre
will require this information.
23
Mod.
Prod.
..........
No. ...........
Ser
. No. .........
Mod. ..........
Prod. No. ...........
P0042
Ser. No. .........
Problem Possible cause
• The electronic unbalance detection device has cut
• Spinning starts late or the
in because the laundry is not evenly distributed in
laundry is not spun enough:
the drum. The laundry is redistributed by reverse
rotation of the drum. This may happen several
times before the unbalance disappears and
normal spinning can resume. If, after few minutes,
the laundry is still not evenly distributed in the
drum, the machine will spin at a lower speed or
will not spin. If at the end of the programme the
laundry is not spun enough, redistribute the load
manually and select the spin programme.
• The machine is fitted with a type of motor which
• The machine makes an unusual
makes an unusual noise compared with other
noise
traditional motors. This new motor ensures a
softer start and more even distribution of the
laundry in the drum when spinning, as well as
increased stability of the machine.
• Machines based on modern technology operate
• No water is visible in the drum
very economically using very little water without
affecting performance.
Bästa kund,
vi ber dig att läsa igenom den här bruksanvisningen
noggrant.
Framför allt är det viktigt att du läser
säkerhetsinformationen på de första sidorna i
bruksanvisningen. Förvara alltid bruksanvisningen
lättillgänglig, så att du snabbt kan hitta den och slå
upp information i den vid ett senare tillfälle. Om du
säljer maskinen ska bruksanvisningen överlämnas
till nästa ägare.
Transportskador
Kontrollera att maskinen inte är skadad. Eventuella
transportskador skall omedelbart anmälas till den
som ansvarat för transporten. Skador, felaktigheter
och ev. saknade delar skall omedelbart anmälas till
säljaren.
Så här använder du bruksanvisningen
Några stycken i bruksanvisningen är försedda med en symbol. Dessa symboler betyder följande:
Här finns viktig information om olämplig användning av maskinen som skulle kunna förorsaka
person- och egendomsskada.
Här finns information, som är särskilt viktig för att erhålla bästa möjliga tvättresultat.
Här finns viktiga miljö- och energispartips.
Vårt bidrag till miljöskyddet är att vi använder returpapper.
24
Innehållsförteckning
Viktig säkerhetsinformation 26-27
Skötsel och rengöring 39
Rengöring av höljet 39
Bortskaffning/avfallshantering 27
Rengöring av tvättmedelslådan 39
Rengöring av lådöppningen 39
Energisparråd 27
Rengöring av avloppssilen 40
Rengöring av tilloppsslangens filter 40
FÖR ANVÄNDAREN
Rengöring av maskinen 40
Avkalkning av maskinen 40
Din nya maskin 28
SVENSKA
Åtgärd vid frysrisk 40
Nödtömning 40
Beskrivning av maskinen 28
Lucklåsningslampa 28
Om maskinen inte fungerar 41-42
Tvättmedelslådan 28
Service och reservdelar 43
Konsumentköp EHL 43
Bruk 29
Garanti (gäller för Finland) 43
Kontrollpanel 29
Konsumentkontakt 43
Beskrivning av maskinens panelfunktioner 29-31
Viktiga råd och tips
FÖR INSTALLATÖREN
för dig som tvättar 32
Tekniska data 44
Sortering av tvätt 32
Temperaturer 32
Hur mycket tvätt per omgång? 32
Installation 45
Tvättmedel och tillsatser 32-33
Uppackning 45
Tvättmärkning 34
Tillbehör 45
Transportsäkring 45
Så här använder du maskinen 35
Placering 45
Lägg i tvätten 35
Nivåjustering 45
Fyll på tvättmedel 35
Vattenanslutning 46
Tillsätt sköljmedel 35
Avloppsanslutning 46-47
Sätt på maskinen 35
●
Över kanten på en vask 46
Välj önskat program 35
●
Anslutning till golvbrunn 46
Välj temperatur 35
●
Anslutning till vattenlås 47
Välj centrifugering eller sköljstopp 36
Elektrisk anslutning 47
Välj önskat alternativ 36
Starta programmet 36
Ändra inställningar under programmets gång 36
Annullera ett pågående program 36
Öppna luckan under programmets gång 37
Avslutning av program 37
Programöversikt 38
25
