Zanussi ZBB7297: TECHNICAL INFORMATION

TECHNICAL INFORMATION: Zanussi ZBB7297

TECHNICAL INFORMATION

Fridge Net Capacity lt.

210

Freezer Net Capacity lt.

70

Energy Consumption kWh/24h

0,871

Energy Consumption kWh/annuo

318

Freezing Capacity kg/24h

4

Rising Time

24

The Technical info are on the rating plate situated on the left inside the appliance.

INSTALLATION

Location

Attention

The appliance should be installed well away from

sources of heat such as radiators, boilers, direct

It must be possible to disconnect the appliance from

sunlight etc.

the mains power supply; the plug must therefore be

easily accessible after installation.

For building into kitchen units follow the special “

Building-in” instructions given.

Electrical connection

Before plugging in, ensure that the voltage and

frequency shown on the serial number plate

correspond to your domestic power supply. Voltage

can vary by ±6% of the rated voltage.

For operation with different voltages, a suitably sized

auto-transformer must be used.

The appliance must be earthed.

The power supply cable plug is provided with a

contact for this purpose.

If the domestic power supply socket is not earthed,

connect the appliance to a separate earth in

compliance with current regulations, consulting a

specialist technician.

The Manufacturer declines all responsibility if

the above safety precautions are not observed.

This appliance complies with the following

E.E.C. Directives:

- 87/308 EEC of 2/6/87 relative to radio interference

suppression.

- 73/23 EEC of 19.2.73 (Low Voltage Directive) and

subsequent modifications;

- 89/336 EEC of 3.5.89 (Electromagnetic

Compatibility Directive) and subsequent

modifications.

24

Instructions for totally built-in appliances

Door reversibility

The appliance is supplied with the right

or left door opening. To change the opening

direction of the door proceed as in the

following instructions before installing it.

1. Unscrew the upper pin and remove the spacer.

2. Remove the upper pin and the upper door.

3. Unscrew the middle hinge.

4. Remove the lower door.

5. Unscrew the lower pin and refit it on the opposite side

6. Refit the lower door.

7. Rescrew the middle hinge und the covers on the

opposite side.

8. Refit the upper door and rescrew the hinge pin and

the spacer on the opposite side.

Instructions for totally built-in

50 mm

min.

2

appliances

200 cm

Dimensions of the recess

Height (1) 1780 mm

Depth (2) 550 mm

min.

2

200 cm

Width (3) 560 mm

For safety reasons, minimum ventilation must be as

shown in Fig. Attention: keep ventilation openings

D567

clear of obstruction.

5

0

540

Furthermore, it is necessary that the niche is provid

with a conduct of ventilation having the following

3

dimensions:

depth 50 mm

width 540 mm

2

1

PR01

25

Make sure that a distance of 44 mm is maintained in

the lower part between the kitchen furniture and the

border of the appliance.

The lower hinge cover inserted in the accessories

1

bag, is useful to guarantee the exact position of the

kitchen furniture and the appliance.

Also make sure that the appliance does not clamp

44mm

the mains cable

2

Fasten the appliance with 4 screws provided in the

kit included with the appliance.

(I = short) (P = long)

I

P

Apply the sealing strip pushing it between the

refrigerator and the adjacent cabinet.

D724

From the plastic cover (E), which is used to cover the

hinge with the pivot pin, you must take away the part

as indicated in the drawing.

This operation is made easer since there is, in the

internal part of the cover hinge lid a groove that

facilates the removal of this coomponent.

“Remove the part marked with DX, if the pivot pin is

inserted in the right hinge, SX in opposite case.

Apply covers (C-D) on joint cover lugs and into hinge

holes.

Snap vent grille (B) and hinge covers (E) into

position.

C

D

E

E

B

26

Separate parts Ha, Hb, Hc, Hd as shown in the

figure.

Ha

Hb

Hc

Hd

PR266

Place guide (Ha) on the inside part of the furniture

ca. 50 mm

door, up and down as shown in the figure and mark

90°

the position of external holes. After having drilled

holes, fix the guide with the screws supplied.

2

1 m

m

90°

ca. 50 mm

2

1

m

m

Fix cover (Hc) on guide (Ha) until it clips into place

Ha

Hc

PR33

8mm

Open the appliance door and the furniture door at

90°. Insert the small square (Hb) into guide (Ha).

Put together the appliance door and the furniture

door and mark the holes as indicated in the figure. .

Ha

Hb

PR167

Remove the brackets and mark a distance of 8 mm

8mm

from the outer edge of the door where the nail must

be fitted (K).

K

Ha

27

Place the small square on the guide again and fix it

with the screws supplied.

Should the lining up of the furniture door be

necessary, use the clearance of slots.

At the end of operations, it is necessary to check if

the door of the furniture closes properly.

Hb

PR168

Fix cover (Hd) on guide (Hb) until it clips into place.

Hb

Hd

PR167/1

If the appliance is to be fitted laterally to the kitchen

unit, it will be sufficient to loosen the screws of the

little plates (D), move them as shown in Fig. and

D

then fasten them up again. Fit the cover (E).

E

D734

After having reversed the opening direction of

the doors check that all the screws are properly

tightened and that the magnetic seal adheres to

the cabinet. If the ambient temperature is cold

(i.e. in Winter), the gasket may not fit perfectly to

the cabinet. In that case, wait for the natural

fitting of the gasket or accelerate this process by

heating up the part involved with a normal

hairdrier.

28

www.electrolux.com

www.zanussi.ru