Pioneer VSX-519V-K: Setting What it does Option(s)
Setting What it does Option(s): Pioneer VSX-519V-K
Table of contents
- IMPORTANT
- Information for users on collection and disposal of old equipment and used batteries
- Contents
- Chapter 1: Before you start
- Chapter 2: 5 minute guide
- Chapter 3: Connecting up
- Connecting up03 Analog audio cables Component video cables Digital audio cables About video outputs connection Video cables
- Connecting a TV and Blu-ray Disc player or DVD player
- Connecting the multichannel analog outputs
- Connecting a satellite receiver or other digital set-top box
- Connecting other audio components Connecting to the front panel audio mini jack
- Connecting other video components
- Using the component video jacks
- Connecting antennas
- Connecting the speakers
- Connecting up 03 Hints on speaker placement Speaker placement diagrams
- Connecting an IR receiver Plugging in the receiver
- Chapter 4: Controls and displays Front panel
- Operating range of remote control unit
- Display
- Controls and displays04
- Remote control
- Controls and displays04
- Controls and displays 04
- Chapter 5: Listening to your system Listening in surround sound Auto playback
- Listening in stereo
- Using Front Stage Surround Advance Using the Sound Retriever Using Stream Direct
- Using Phase Control
- Setting the Audio options Setting What it does Option(s)
- Setting What it does Option(s)
- Playing other sources Selecting the multichannel analog inputs Choosing the input signal Using the headphone
- Chapter 6: The System Setup menu Using the System Setup menu Manual speaker setup
- The System Setup menu06 Channel level Crossover network
- Speaker Distance The Input Assign menu
- Chapter 7: Using the MULTI-ZONE feature MULTI-ZONE listening
- Using the MULTI-ZONE feature 07 Using the MULTI-ZONE controls MULTI-ZONE remote controls
- Chapter 8 Using the tuner Listening to the radio Saving station presets
- Using the tuner 08 Naming preset stations
- An introduction to RDS Searching for RDS programs
- Displaying RDS information
- Chapter 9: Making recordings Making an audio or a video recording
- Chapter 10: Additional information Troubleshooting Problem Remedy
- Problem Remedy
- HDMI Symptom Remedy Important information regarding the HDMI connection
- Resetting the main unit Specifications
- Cleaning the unit
VSX_519V_MY.book 31 ページ ２００９年１月１６日 金曜日 午後７時３２分
Listening to your system 05
Setting What it does Option(s)
English
DRC
Adjusts the level of dynamic range for movie soundtracks
OFF
(Dynamic Range
optimized for Dolby Digital and DTS (you may need to use
MAX
this feature when listening to surround sound at low
Control)
volumes).
MID
LFE ATT
Some Dolby Digital and DTS audio sources include ultra-
LFEATT 0 (0 dB)
Français
(LFE Attenuate)
low bass to
nes. Set the LFE attenuator as necessary to
LFEATT 10 (–10 dB)/
prevent the ultra-low bass tones from distorting the sound
LFEATT ** (OFF)
from the speakers.
The LFE is not limited when set to 0 dB, which is the
recommended value. When set to –10 dB, the LFE is
limited by the respective degree. When OFF is selected, no
sound is output from the LFE channel.
Specifies the routing of the HDMI audio signal out of this
AMP
HDMI
(HDMI Audio)
receiver (amp) or through to a TV or flat screen TV. When
THRU
THRU is selected, no sound is output from this receiver.
A.DLY
This feature automatically corrects the audio-to-video delay
OFF
(Auto Delay)
between components connected with an HDMI cable. The
Italiano
ON
audio delay time is set depending on the operational status
of the display connected with an HDMI cable. The video
delay time is automatically adjusted according to the audio
d
delay time.
e
Spreads the center channel between the front right and left
0 to 7
C.WIDTH
Nederlands
speakers, making it sound wider (higher settings) or
Default: 3
(Center Width)
narrower (lower settings).
(Applicable only when
using a center speaker)
e
Adjusts the surround sound balance from front to back,
–3 to +3
DIMEN.
making the sound more distant (minus settings), or more
(Dimension)
Default: 0
forward (positive settings).
Español
e
Extends the front stereo image to include surround
OFF
PNRM.
speakers for a ‘wraparound’ effect.
(Panorama)
ON
a. You can change the MIDNIGHT/LOUDNESS options at any time by using MIDNIGHT button.
b. You can change the Sound Retriever feature at any time by using S.RETRIEVER button.
c. This setting works only with dual mono encoded Dolby Digital and DTS soundtracks.
Deutsch
d. This feature is only available when the connected display supports the automatic audio/video
synchronizing capability (‘lip-sync’) for HDMI. If you find the automatically set delay time unsuitable, set
A.DLY to OFF and adjust the delay time manually. For more details about the lip-sync feature of your
display, contact the manufacturer directly.
e. Only available with 2-channel sources in DOLBY PLII MUSIC mode.
31
En
