Pioneer VSX-519V-K: Resetting the main unit Specifications
Resetting the main unit Specifications: Pioneer VSX-519V-K
Table of contents
- IMPORTANT
- Information for users on collection and disposal of old equipment and used batteries
- Contents
- Chapter 1: Before you start
- Chapter 2: 5 minute guide
- Chapter 3: Connecting up
- Connecting up03 Analog audio cables Component video cables Digital audio cables About video outputs connection Video cables
- Connecting a TV and Blu-ray Disc player or DVD player
- Connecting the multichannel analog outputs
- Connecting a satellite receiver or other digital set-top box
- Connecting other audio components Connecting to the front panel audio mini jack
- Connecting other video components
- Using the component video jacks
- Connecting antennas
- Connecting the speakers
- Connecting up 03 Hints on speaker placement Speaker placement diagrams
- Connecting an IR receiver Plugging in the receiver
- Chapter 4: Controls and displays Front panel
- Operating range of remote control unit
- Display
- Controls and displays04
- Remote control
- Controls and displays04
- Controls and displays 04
- Chapter 5: Listening to your system Listening in surround sound Auto playback
- Listening in stereo
- Using Front Stage Surround Advance Using the Sound Retriever Using Stream Direct
- Using Phase Control
- Setting the Audio options Setting What it does Option(s)
- Setting What it does Option(s)
- Playing other sources Selecting the multichannel analog inputs Choosing the input signal Using the headphone
- Chapter 6: The System Setup menu Using the System Setup menu Manual speaker setup
- The System Setup menu06 Channel level Crossover network
- Speaker Distance The Input Assign menu
- Chapter 7: Using the MULTI-ZONE feature MULTI-ZONE listening
- Using the MULTI-ZONE feature 07 Using the MULTI-ZONE controls MULTI-ZONE remote controls
- Chapter 8 Using the tuner Listening to the radio Saving station presets
- Using the tuner 08 Naming preset stations
- An introduction to RDS Searching for RDS programs
- Displaying RDS information
- Chapter 9: Making recordings Making an audio or a video recording
- Chapter 10: Additional information Troubleshooting Problem Remedy
- Problem Remedy
- HDMI Symptom Remedy Important information regarding the HDMI connection
- Resetting the main unit Specifications
- Cleaning the unit
VSX_519V_MY.book 46 ページ ２００９年１月１６日 金曜日 午後７時３２分
Additional information10
Resetting the main unit
Specifications
Use this procedure to reset all the r eceiver ’s
Audio section
settings to the factory default. Use the front
Rated power output
panel controls to do this.
Front, Center, Surround
1 Switch the receiver into standby.
. . . . . . . . .130 W per channel (1 kHz, 6
Ω
, 1 %)
. . . . . . . . . . . . . . . . . . . . . . . 100 W per channel
2 While holding down the
BAND
button,
(20 Hz to 20 kHz, 8
Ω
, 0.09 %)
press and hold the
STANDBY/ON button
Total Harmonic Distortion
for about two seconds.
. . . . . . 0.06 % (20 Hz to 20 kHz, 8
Ω
, 95 W/ch)
Frequency response (LINE Pure Direct mode)
3 When you see RESET? appear in the
. . . . . . . . . . . . . . . . . . . . 5 Hz to 100 kHz dB
display, press the ‘AUTO SURROUND/
Guaranteed speaker impedance . . . 6
Ω
to 16
Ω
STREAM DIRECT’ button.
Input (Sensitivity/Impedance)
OK? shows in the display.
LINE . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 k
Ω
4Press ‘
STEREO/A.L.C.
’ to confirm.
Output (Level/Impedance)
OK appears in the display to indicate that the
REC . . . . . . . . . . . . . . . . . . . . . . . 200 mV/330
Ω
receiver has been reset to the factory default
ZONE 2 . . . . . . . . . . . . . . . . . . . . . 200 mV/1 kΩ
settings.
Signal-to-Noise Ratio
(IHF, short circuited, A network)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dB
Video Section
Signal level
Composite . . . . . . . . . . . . . . . . . . 1 Vp-p (75
Ω)
Component Video . . . . . . . . Y: 1.0 Vp-p (75
Ω)
PB, PR: 0.7 Vp-p (75
Ω)
Corresponding maximum resolution
Component Video . . . . . . . . . . . 1080p (1125p)
Tuner Section
FM Frequency Range . . . . 87.5 MHz to 108 MHz
Antenna Input . . . . . . . . . . . . . 75 Ω unbalanced
AM Frequency Range . . . . . 531 kHz to 1602 kHz
Antenna . . . . . . . . . . . . . . . . . . . . . Loop antenna
Digital I/O
HDMI terminal . . . . . . . . . . . . . . 19-pin (Not DVI)
HDMI output type . . . . . . . . . . . . . . . 5 V, 100 mA
Integrated control section
Control (IR) terminal. . . ∅ 3.5 Mini-jack (MONO)
IR signal . . . . . . .High Active (High Level : 2.0 V)
46
En
