Pioneer CP-81B-K: instruction

FRRD-235-A_CP-81_En.book 1 ページ ２００８年７月２４日　木曜日　午後２時１５分

Thank you for buying this Pioneer product.

Please read through these operating instructions for proper assembly and use. After you have finished reading the instructions, put them

away in a safe place for future reference.

This speaker stand can be used only with the following Pioneer speaker systems: S-81B-LR-K, S-81B-LR-QL, or S-81B-LR-W.

Before you start

Names of Parts

Before setting up your speaker system, we recommend reading

the operating instructions for your system thoroughly.

• Only use the screws supplied when fixing the speaker to the

speaker stand.

• Do not place the stand on an unstable and/or sloping surface.

The stand and speaker may fall and cause injury.

• Do not use with any speaker system other than the one for

which the unit was designed. The stand may collapse and be

damaged and/or the speaker may fall and cause injury.

• When moving the speaker and stand, first remove the speaker

from the stand, and then move the stand, holding it by the

stems.

• Place the stand on a stable, level surface; placing the stand on

an unstable surface can be dangerous.

• Pioneer assumes no liability whatsoever for damages

resulting from assembly, improper mounting, insufficient

reinforcement, misuse of the product, acts of nature, etc.

2

En

FRRD-235-A_CP-81_En.book 2 ページ ２００８年７月２４日　木曜日　午後２時１５分

When using the spikes

This speaker stand includes spikes that you can use to isolate the

Attaching speakers to the stands

speaker from the floor. Spikes are recommended when placing

A medium Phillips screwdriver is required for assembling the

the stand on a thick carpet (for added stability), or for better sound

speaker stand and for attaching the speaker.

when placing the stand on a hard reverberant surface (such as a

concrete or wood floor). Use the supplied spike bases to avoid

Assembling the speaker stands

scratching the floor or other surface where the stand is placed.

English

Assemble the speaker stands as illustrated below.

Align the screw holes on the stand base and speaker support

with the screw holes in the three stems, then insert the

screws and tighten.

1 Twist the spikes into the threaded metal inserts

embedded in the bottom of the stand base.

2 Set the spike bases in the positions where the points of

the three spikes will strike when the speaker stand is set

down.

3 Set the speaker stand on the spike bases and check to

confirm the speaker stand does not rock.

• Note that these spikes are sharp metal and can cause damage

to flooring. Make sure to lay down a cloth or suitable base

before setting up.

• Always use the spike bases as shown, with the indented

surface facing up to receive the spike point.

• Make sure you assemble the stand on a flat surface that is

relatively soft (such as a carpet).

• Make sure the screws are inserted in the screw holes as

shown above (with the screw head hidden) when securing the

speaker. Improper setup could result in damage or injury if the

speaker falls from the stand.

When using the non-skid pads

3

En

If you do not use the spike bases when placing the

speakers, the spikes may cause damage to the floor. If

you plan on using the spikes we highly recommend to

use the spike bases.

FRRD-235-A_CP-81_En.book 3 ページ ２００８年７月２４日　木曜日　午後２時１５分

When using speaker spikes:

When not using speaker spikes:

To avoid accident or injury, please use screws to secure the

To avoid accident or injury, please use screws to secure the

speaker to the speaker stands. Note that there are fastening nuts

speaker to the speaker stands. Note that there are fastening nuts

provided on the speaker base (see below).

provided on the speaker base (see below).

Secure the speaker to the speaker support using the washer,

Secure the speaker to the speaker support using the washer,

spring washer and the 50 mm (2 in.) screws as shown below.

5

spring washer and the 40 mm (1

/

8

in.) screws as shown below.

50 mm

(2 in.)

Black

4

En

40 mm

5

(1

/8 in.)

Black

FRRD-235-A_CP-81_En.book 4 ページ ２００８年７月２４日　木曜日　午後２時１５分