Pioneer VSX-519V-K: Problem Remedy
Problem Remedy: Pioneer VSX-519V-K
Table of contents
- IMPORTANT
- Information for users on collection and disposal of old equipment and used batteries
- Contents
- Chapter 1: Before you start
- Chapter 2: 5 minute guide
- Chapter 3: Connecting up
- Connecting up03 Analog audio cables Component video cables Digital audio cables About video outputs connection Video cables
- Connecting a TV and Blu-ray Disc player or DVD player
- Connecting the multichannel analog outputs
- Connecting a satellite receiver or other digital set-top box
- Connecting other audio components Connecting to the front panel audio mini jack
- Connecting other video components
- Using the component video jacks
- Connecting antennas
- Connecting the speakers
- Connecting up 03 Hints on speaker placement Speaker placement diagrams
- Connecting an IR receiver Plugging in the receiver
- Chapter 4: Controls and displays Front panel
- Operating range of remote control unit
- Display
- Controls and displays04
- Remote control
- Controls and displays04
- Controls and displays 04
- Chapter 5: Listening to your system Listening in surround sound Auto playback
- Listening in stereo
- Using Front Stage Surround Advance Using the Sound Retriever Using Stream Direct
- Using Phase Control
- Setting the Audio options Setting What it does Option(s)
- Setting What it does Option(s)
- Playing other sources Selecting the multichannel analog inputs Choosing the input signal Using the headphone
- Chapter 6: The System Setup menu Using the System Setup menu Manual speaker setup
- The System Setup menu06 Channel level Crossover network
- Speaker Distance The Input Assign menu
- Chapter 7: Using the MULTI-ZONE feature MULTI-ZONE listening
- Using the MULTI-ZONE feature 07 Using the MULTI-ZONE controls MULTI-ZONE remote controls
- Chapter 8 Using the tuner Listening to the radio Saving station presets
- Using the tuner 08 Naming preset stations
- An introduction to RDS Searching for RDS programs
- Displaying RDS information
- Chapter 9: Making recordings Making an audio or a video recording
- Chapter 10: Additional information Troubleshooting Problem Remedy
- Problem Remedy
- HDMI Symptom Remedy Important information regarding the HDMI connection
- Resetting the main unit Specifications
- Cleaning the unit
VSX_519V_MY.book 44 ページ ２００９年１月１６日 金曜日 午後７時３２分
Additional information10
Problem Remedy
Broadcast stations cannot be
• Connect an outdoor antenna (refer to page 15).
selected automatically.
No sound from surround or
• Connect the speakers properly (refer to page 16).
center speakers.
• Refer to Speaker setting on page 33 to check the speaker settings.
• Refer to Channel level on page 34 to check the speaker levels.
No sound from subwoofer.• Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have
an LFE channel.
• Switch the subwoofer setting in Speaker setting on page 33 to YES
or PLUS.
• Switch the LFEATT (LFE
Attenuate) on page 31 to LFEATT 0 or
LFEATT 10.
The PHASE CONTROL feature
• If applicable, check that the lowpass filter switch on your
doesn’t seem to have an
subwoofer is off, or the lowpass cutoff is set to the highest frequency
audible effect.
setting. If there is a PHASE setting on your subwoofer, set it to 0º (or
depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers
(see Speaker Distance on page 35).
Noise during playback of a
• Move the cassette deck further from your rec
eiver, until the noise
cassette deck.
disapp
ears.
No sound is output or a noise
• Set the digital volume level of the player to full, or to the neutral
is output when software with
position.
DTS is played back.
• Make sure the player’s settings are correct and/or the DTS signal
out is on. Refer to the instruction manual supplied with the DVD
player.
• Set the input signal type to C1/O1/O2 (DIGITAL) (see Choosing the
input signal on page 32).
During a playback search,
• This is not a malfunction, but be sure to turn the volume down to
noise is output from a DTS
prevent the output of loud noise from your speak
ers.
compatible CD player.
Everything seems to be set up
• Check that the positive/negative speaker terminals on the receiver
correctly, but the playback
are matched with the corresponding terminals on the speakers (see
sound is odd.
Connecting the speakers on page 16).
Can’t operate the remote
• Replace the batteries (refer to page 20).
control.
• Operate within 7 m, 30°
of the remote sensor on the front panel
(refer to page 5).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off. • Press DIMMER on the remote repeatedly to return to the default.
44
En
