Indesit WITL 106: инструкция

Instructions for use

WASHING MACHINE

GB

Contents

GB

CIS

ES

I

Installation, 2-3

English, 1

Русский,13

Italiano, 25

Unpacking and levelling

Electric and water connections

The first wash cycle

UK

CZ

SK

Technical details

Українська, 37

Český, 49

Slovenský, 61

Washing machine description, 4-5

Control panel

How to open and shut the drum

KZ

Leds

Кaзaкшa,73

Starting and Programmes, 6

Briefly: how to start a programme

Programme table

Personalisations, 7

Setting the temperature

WITL 1061

Setting the spin cycle

Functions

Detergents and laundry, 8

Detergent dispenser

Bleach cycle

Preparing your laundry

Special items

Woolmark Gold

Precautions and advice, 9

General safety

Disposal

Saving energy and respecting the environment

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning your appliance

Caring for your appliance door and drum

Cleaning the pump

Checking the water inlet hose

Cleaning the detergent dispenser

Troubleshooting, 11

Service, 12

Before calling for Assistance

1

Installation

! Keep this instruction manual in a safe place for future refe-

Putting your appliance in place and moving it.

GB

rence. Should the appliance be sold, transferred or moved,

If your washing machine

make sure the instruction manual accompanies the washing

is equipped with a special

machine to inform the new owner as to its operation and

set of retractable wheels

features.

you can easy move it.

To lower the wheels and

! Read these instructions carefully: they contain vital infor-

thus move the appliance

mation on installation, use and safety.

effortlessly, just pull the

lever, situated on the left-

Unpacking and levelling

hand side beneath the

base. Once the appliance

Unpacking

is in the required position,

1. Unpack the washing

put the lever back in place. The washing machine is now

machine.

firmly in place (see figure).

2. Check whether the

Electric and water connections

washing machine has been

damaged during transport.

Connecting the water inlet hose

If this is the case, do not

install it and contact your

1. Connect the supply

retailer.

pipe by screwing it to a

cold water tab using a ¾

3. Remove the four protec-

gas threaded connection

tive screws and the rubber

(see figure).

washer with the respective

Before performing the

spacer, situated on the

connection, allow the

rear of the appliance (see

water to run freely until it is

figure).

perfectly clear.

4. Seal the gaps using the

plastic plugs provided.

2. Connect the other end of

5. Keep all the parts: you will need them again if the washing

the water inlet hose to the

machine needs to be moved to another location.

washing machine,

screwing it onto the applian-

Warning: should the screws be re-used, make sure you fasten

ce’s cold water inlet, situated

the shorter ones at the top.

on the top right-hand side

! Packaging materials are not children’s toys.

on the rear of the appliance

(see figure).

Levelling

3. Make sure there are

1. Install the washing machine

no kinks or bends in the

on a flat sturdy floor, without

hose.

resting it up against walls,

furniture cabinets or other.

! The water pressure at the tap must be within the values

indicated in the Technical details table

2. If the floor is not perfectly

(on the next page).

level, compensate for any

! If the water inlet hose is not long enough, contact a

unevenness by tightening or lo-

specialist store or an authorised serviceman.

osening the adjustable front feet

! Never use hoses that have already been used.

(see figure); the angle of inclina-

tion, measured according to the

worktop, must not exceed 2°.

Levelling your appliance correctly will provide it with stability

and avoid any vibrations, noise and shifting during operation.

If it is placed on a fitted or loose carpet, adjust the feet in

such a way as to allow enough room for ventilation beneath

the washing machine.

2

Connecting the drain hose

! Do not use extensions or multiple sockets.

GB

Connect the drain hose,

! The power supply cable must never be bent or dange-

without bending it, to a

rously compressed.

draining duct or a wall

drain situated between 65

! The power supply cable must only be replaced by an

and 100 cm from the floor;

authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

alternatively, place it over

Once the appliance has been installed, and before you

the edge of a basin, sink

use it for the first time, run a wash cycle with detergent

or tub, fastening the duct

and no laundry, setting the 90°C programme without a

supplied to the tap (see

pre-wash cycle.

figure). The free end of

the hose should not be

underwater.

! We advise against the use of hose extensions; in case

of absolute need, the extension must have the same

diameter as the original hose and must not exceed 150

cm in length.

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

• the socket is earthed and in compliance with the

applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated in the Technical

details table (on the right);

• the supply voltage is included within the values i

ndicated on the Technical details table

(on the right);

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace

the socket or the plug.

! The washing machine should not be installed in an ou-

tdoor environment, not even when the area is sheltered,

because it may be very dangerous to leave it exposed to

rain and thunderstorms.

! When the washing machine is installed, the mains so-

cket must be within easy reach.

3

Technical details

Model

WITL 1061

40 cm wide

Dimensions

85 cm high

60 cm deep

Capacity

from 1 to 5 kg

Electric

Please refer to the technical data plate

connections

fixed to the machine.

maximum pressure 1 MPa (10 bar)

Water

minimum pressure 0.05 MPa (0.5 bar)

connections

drum capacity 42 litres

Spin speed

up to 1000 rpm

Test wash

cycles in

accordance

Programme : Cotton standard 60°C;

with directives

Programme : Cotton standard 40°C.

1061/2010 and

1015/2010.

This appliance is compliant with

the following European Community

Directives:

- 2004/108/CEE (Electromagnetic

Compatibility)

- 2006/95/CE (Low Voltage)

- 2002/96/CE