Indesit WIE 107: инструкция

Instructions for use

WASHING MACHINE

Contents

GB

Installation, 2-3

GB

CIS

SL

Unpacking and levelling, 2

Electric and water connections, 2-3

English,1

ÐÓÑÑÊÈÉ,13

Slovenèina,25

The first wash cycle, 3

Technical details, 3

Washing machine description, 4-5

HR

HU

GR

Control panel, 4

Display, 5

Hrvatski,37

Magyar,4 9

ÅËËÇÍÉÊÁ,61

MEMO Programme, 5

Starting and Programmes, 6

Briefly: how to start a programme, 6

Programme table, 6

Personalisations, 7

Setting the spin cycle, 7

WIE 107

Setting the Delay Timer, 7

Setting the temperature, 7

Functions, 7

Detergents and laundry, 8

Detergent dispenser, 8

Bleach cycle, 8

Preparing your laundry, 8

Special items, 8

Precautions and advice, 9

General safety, 9

Disposal, 9

Saving energy and respecting the environment, 9

Care and maintenance, 10

Cutting off the water or electricity supply, 10

Cleaning your appliance, 10

Cleaning the detergent dispenser, 10

Caring for your appliance door and drum, 10

Cleaning the pump, 10

Checking the water inlet hose, 10

Troubleshooting, 11

Service, 12

Before calling for Assistance, 12

1

Installation

 Keep this instruction manual in a safe place for

Levelling your appliance correctly will provide it with

GB

future reference. Should the appliance be sold,

stability and avoid any vibrations, noise and shifting

transferred or moved, make sure the instruction

during operation. If it is placed on a fitted or loose

manual accompanies the washing machine to inform

carpet, adjust the feet in such a way as to allow

the new owner as to its operation and features.

enough room for ventilation beneath the washing

machine.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Electric and water connections

Unpacking and levelling

Connecting the water inlet hose

Unpacking

1. Insert seal A into the

1. Unpack the washing machine.

end of the inlet hose

2. Check whether the washing machine has been

and screw the latter

damaged during transport. If this is the case, do not

onto a cold water tap

install it and contact your retailer.

with a 3/4 gas threaded

A

mouth (see figure).

3. Remove the 3

Before making the

protective screws and

connection, allow the

the rubber washer with

water to run freely until

the respective spacer,

it is perfectly clear.

situated on the rear of

the appliance (see

2. Connect the other end

figure).

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

4. Seal the gaps using the plastic plugs provided.

rear of the appliance

5. Use the plug provided to seal the three holes

(see figure).

where the plug was housed, situated on the lower

right-hand side on the rear of your appliance.

6. Keep all the parts: you will need them again if the

3. Make sure there are no kinks or bends in the

washing machine needs to be moved to another

hose.

location.

 The water pressure at the tap must be within the

 Packaging materials are not children's toys.

values indicated in the Technical details table

(on the next page).

Levelling

 If the water inlet hose is not long enough, contact

1. Install the washing machine on a flat sturdy floor,

a specialist store or an authorised serviceman.

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet (see figure);

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

2

Connecting the drain hose

 Do not use extensions or multiple sockets.

GB

Connect the drain hose,

 The power supply cable must never be bent or

without bending it, to a

dangerously compressed.

draining duct or a wall

drain situated between

 The power supply cable must only be replaced by

65 and 100 cm from

an authorised serviceman.

65 - 100 cm

the floor;

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before

alternatively, place it

you use it for the first time, run a wash cycle with

over the edge of a

detergent and no laundry, setting the 90°C

basin, sink or tub,

programme without a pre-wash cycle.

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

Technical details

exceed 150 cm in length.

Electric connection

Model

WIE 107

Before plugging the appliance into the mains

59.5 cm wide

Dimensions

85 cm high

socket, make sure that:

52.5 cm deep

 the socket is earthed and in compliance with the

applicable law;

Capacity

from 1 to 5 kg

 the socket is able to sustain the appliance's

Electric

voltage 220/230 Volts 50 Hz

maximum power load indicated in the Technical

connections

maximum absorbed power 1850 W

details table (on the right);

maximum pressure 1 MPa (10 bar)

Water

minimum pressure 0.05 MPa (0.5 bar)

connections

 the supply voltage is included within the values i

drum capacity 46 litres

ndicated on the Technical details table

(on the right);

Spin speed

up to 1000 rpm

Control

 the socket is compatible with the washing

programmes

programme 2; temperature 60°C;

machine's plug. If this is not the case, replace

according to

run with a load of 5 kg.

the socket or the plug.

IEC456 directive

This appliance is compliant with the

 The washing machine should not be installed in an

following European Community

outdoor environment, not even when the area is

Directives:

sheltered, because it may be very dangerous to

- 73/23/CEE of 19/02/73 (Low

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

leave it exposed to rain and thunderstorms.

Voltage) and subsequent amendments

- 89/336/CEE of 03/05/89

 When the washing machine is installed, the mains

(Electromagnetic Compatibility) and

subsequent amendments

socket must be within easy reach.

3