Indesit WIXXL 106: инструкция

Instruction booklet

WASHING MACHINE

Contents

GB

Installation, 2-3

GB

Unpacking, 2

Remove the transit fixings, 2

English

Levelling, 2

Water connections, 2

Drainage and electrical connections, 3

Technical Details, 3

Washing machine description, 4-5

Control panel, 4

LEDs, 5

Starting and programmes, 6

Briefly: starting a programme, 6

Programme table, 6

Personalisations, 7

WIXXL 106

Setting the temperature, 7

Setting the spin speed, 7

Options, 7

Detergents and laundry, 8

Detergent dispenser, 8

Maximum load size, 8

Precautions and advice, 9

General safety, 9

Disposal, 9

Saving energy and respecting

the environment, 9

Care and Maintenance, 10

Switching off the water or electricity supply, 10

Cleaning, 10

Caring for your appliance door and drum, 10

Cleaning the pump, 10

Checking the water inlet hose, 10

Troubleshooting, 11

Service, 12

Before calling for assistance, 12

1

WIXXL106-GB-indesit.p65 13/09/05, 14.291

Installation

Keep this instruction manual in a safe place for future

Levelling

GB

reference. Should the appliance be sold, transferred or

Your machine will be noisy if the two front feet are not

moved, make sure the instruction manual

adjusted so that the machine stands firm and level.

accompanies the washing machine to inform the new

! The machine should be levelled from side to side and

owner as to its operation and features.

from front to back.

! Read these instructions carefully: they contain vital

1. Move your machine into its final location.

information on installation, use and safety.

- Take care not to trap or kink

the hoses.

Unpacking

2. Turn one or both front feet

1. Unpack the machine.

anti-clockwise by hand until the

2. Check whether the machine has been damaged

feet cannot be turned any more.

during transport. If this is the case, do not install it and

When adjusting the feet, use a

contact your retailer.

spirit level to check the machine

Remove the transit fixings

stands level, from side to side

IMPORTANT: Follow these instructions to remove the

and from front to back.

TWO transit fixings (see Description for location).

- The spring on each foot will stop them coming loose.

Situated on either side of the

! If it is placed on a fitted or loose carpet, adjust the

rear panel,

BOTH transit bolts

BOTH transit boltsBOTH transit bolts

BOTH transit boltsBOTH transit bolts

feet in such a way as to allow enough room for

MUST be r

MUST be rMUST be r

MUST be rMUST be r

emoved befor

emoved beforemoved befor

emoved beforemoved befor

e use.

e usee use

e usee use

ventilation beneath the machine.

! Failure to do so may cause

damage to your machine.

It is important the transit bolt

Water connection

and spacer (see pic) come out

Connecting the water inlet hose.

intact.

Remember that this is a cold-fill machine.

1. Unscrew the bolt using a

! Check that seal is in place

13mm spanner.

inside the hose end cap.

2. STOP when 3 threads can be

Before making the water connections to gas ¾ thread,

seen.

allow the water to run freely from the supply tap until it

is perfectly clear.

Screw the inlet end with the blue

cap onto the cold water supply

tap.

3. Hold, slide sideways and pull

to remove.

Turn the taps on and check for leaks: tighten if

necessary.

! Make sure there are no kinks or bends in the hose.

! The water pressure at the tap must be within the

values indicated in the Technical details table (next

4. For safety, insert one of the

page).

the plastic covers (supplied with

! If the water inlet hose is not long enough, contact a

your machine) over the hole.

specialist store or an authorised serviceman.

! Repeat steps 1 to 4 to remove

! Always use new hoses.

the second transit bolt.

! Check the water hose at least once a year, replace

! Packaging materials are not

any that are cracked as worn hoses could split under

children’s toys.

water pressure.

2

WIXXL106-GB-indesit.p65 13/09/05, 14.292

Drainage connections

The first wash cycle

GB

A. Connect the drain

Once the appliance has been installed and before you

B

hose, without kinking it,

use it for the first time, run a wash cycle without

A

to a draining duct or a

detergent and no laundry, setting the 90°C

wall drain fixed at a

programme without a pre-wash cycle.

height between 65 and

100cm from the floor.

B. Alternatively, place it

TECHNICAL DETAILS

over the edge of a basin,

sink or tub, fastening the

Model

WIXXL 106

hose supplied to the tap.

The free end of the hose should not be under water.

59.5 cm wide

Dimensions

85 cm high

! We advise against the use of hose extensions. In

52.5 cm deep

case of absolute need, the extension must have the

Capacity

from 1 to 7 kg

same diameter as the original hose and must not

exceed 150cm in length.

Electric

voltage 220 - 240 volts 50 Hz

connections

absorbed power 1700 – 2100 W

Electrical connections

maximum pressure 1 MPa (10 bar)

Water

minimum pressure 0,05 MPa (0,5 bar)

connection

Before plugging the appliance into the mains socket,

drum capacity 53 litres

make sure that:

• the socket is earthed and in compliance with the

Spin speed

up to 1000 rpm

applicable law.

• the socket is able to sustain the appliances

Control

maximum power load indicated in the Technical

programmes

programme 2 with temperature set to

according to

Details table (on the right).

60°C run with a load of 7 kg.

the IEC456

• the supply voltage is included within the values

directive

indicated in the Technical Details table (on the right).

• the socket is compatible with the washing machines

This appliance is compliant with the

plug. If this is not the case, replace the socket or

following European Community

directives:

the plug.

- 73/23/CEE of 19/02/73 (Low Voltage)

and subsequent amendments

! The washing machine should not be installed in an

- 89/336/CEE of 03/05/89

outdoor environment, not even when the area is

(Electromagnetic Compatibility) and

sheltered, because it may be very dangerous to leave

subsequent amendments

it exposed to rain and thunderstorms.

! When the washing machine is installed, the mains

socket must be within easy reach and should be

connected to a suitable electrical supply.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by an

authorised serviceman.

! The company denies all liability if and when these

norms are not respected.

3

WIXXL106-GB-indesit.p65 13/09/05, 14.293