Indesit PWE 81472S: инструкция

Instructions for use

WASHING MACHINE

Contents

GB

Installation, 2-3

GB

F

DE

Unpacking and levelling

Connecting the electricity and water supplies

English,1

Français,13

Deutsch,25

The first wash cycle

Technical data

Description of the washing machine, 4-5

NL

ES

PT

Control panel

Display

Português,61

Nederlands,37

Español, 49

Running a wash cycle, 6

Wash cycles and options, 7

CIS

Table of programmes and wash cycles

Wash options

Русский,73

Detergents and laundry, 8

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Precautions and advice, 9

PWE 81472 S

General safety

Disposal

Care and maintenance, 10

Cutting off the water and electricity supplies

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

1

Installation

! This instruction manual should be kept in a safe place for

Levelling the machine correctly will provide it with stability,

GB

future reference. If the washing machine is sold, transferred

help to avoid vibrations and excessive noise and prevent it

or moved, make sure that the instruction manual remains

from shifting while it is operating. If it is placed on carpet or

with the machine so that the new owner is able to

a rug, adjust the feet in such a way as to allow a sufficient

familiarise himself/herself with its operation and features.

ventilation space underneath the washing machine.

! Read these instructions carefully: they contain vital

Connecting the electricity and water

information relating to the safe installation and operation of

supplies

the appliance.

Connecting the water inlet hose

Unpacking and levelling

1. Connect the inlet hose

by screwing it to a cold

Unpacking

water tap using a 3/4 gas

threaded connection (see

1. Remove the washing machine from its packaging.

figure).

2. Make sure that the washing machine has not been

Before performing the

damaged during the transportation process. If it has been

connection, allow the

damaged, contact the retailer and do not proceed any

water to run freely until it is

further with the installation process.

perfectly clear.

3. Remove the 4 protective

screws (used during

2. Connect the inlet hose

transportation) and the

to the washing machine

rubber washer with the

by screwing it onto the

corresponding spacer,

corresponding water inlet

located on the rear part of

of the appliance, which is

the appliance (see figure).

situated on the top right-

hand side of the rear part of

the appliance (see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need them

3. Make sure that the hose is not folded over or bent.

again if the washing machine needs to be moved to

another location.

! The water pressure at the tap must fall within the range

of values indicated in the Technical data table (see next

! Packaging materials should not be used as toys for

page).

children.

! If the inlet hose is not long enough, contact a specialised

Levelling

shop or an authorised technician.

1. Install the washing machine on a flat sturdy floor, without

! Never use second-hand hoses.

resting it up against walls, furniture cabinets or anything

else.

! Use the ones supplied with the machine.

2. If the floor is not perfectly

level, compensate for any

unevenness by tightening or

loosening the adjustable front

feet (see figure); the angle

of inclination, measured in

relation to the worktop, must

not exceed 2°.

2

Connecting the drain hose

GB

Connect the drain hose,

without bending it, to a

drain duct or a wall drain

situated between 65 and

100 cm from the floor;

alternatively, placed it over

the edge of a basin, sink

or tub, fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

! We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the same

diameter as the original hose and must not exceed 150 cm

in length.

Electrical connections

Before plugging the appliance into the electricity socket,

make sure that:

• the socket is earthed and complies with all applicable

laws;

• the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical data

table (see opposite);

• the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

• the socket is compatible with the plug of the washing

machine. If this is not the case, replace the socket or the

plug.

! The washing machine must not be installed outdoors,

even in covered areas. It is extremely dangerous to leave

the appliance exposed to rain, storms and other weather

conditions.

! When the washing machine has been installed, the

electricity socket must remain within easy reach.

! Do not use extension cords or multiple sockets.

3

! The cable should not be bent or compressed.

! The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible in the

event that these standards are not observed.

The first wash cycle

Once the appliance has been installed, and before you use

it for the first time, run a wash cycle with detergent and no

laundry, using wash cycle number 2.

Technical data

Model

PWE 81472 S

width 59.5 cm

Dimensions

height 85 cm

depth 60 cm

Capacity

from 1 to 8 kg

Electrical

please refer to the technical data plate

connections

fixed to the machine

maximum pressure 1 MPa (10 bar)

Water connections

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1400 rotations per minute

Test

Programmes

Programme 2: temperature 60°C and 40°C

according to

2010/1061

This appliance conforms to the following

EC Directives:

- 2004/108/EC (Electromagnetic Compa-

tibility)

- 2006/95/EC (Low Voltage)

- 2002/96/EC