Indesit HIM 506 EK.A IX: инструкция

OVEN

HIM 50 EK.A

HIM 50 EK.A IX

Contents

Installation, 2-4

Positioning

Electrical connections

Data plate

Description of the appliance, 5

Overall view

Control panel

Start-up and use, 6

Starting the oven

Using the cooking timer

Cooking modes, 7-8

Cooking modes

Practical cooking advice

Cooking advice table

Hob, 9

Type of hob

Switching on the glass ceramic hob

Practical advice on using the glass ceramic hob

Precautions and tips, 10

General safety

Disposal

Respecting and conserving the environment

Maintenance and care, 11

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

Assistance

Operating Instructions

GB

Nederlands, 23

English,1

Deutsch, 34

ÅëëçíéêÜ

, 

45

Français, 12

FR

GB

NL

DE

GR

Русский

, 56

RS

2

GB

!

 Before placing your new appliance into operation

please read these operating instructions carefully.

They contain important information for safe use, for

installation and for care of the appliance.

!

 Please keep these operating instructions for future

reference. Pass them on to possible new owners of

the appliance.

Positioning

!

 Keep packaging material out of the reach of

children.

It can become a choking or suffocation

hazard (

see Precautions and tips

).

!

 The appliance must be installed by a qualified

person in compliance with the instructions provided.

Incorrect installation may cause harm to persons,

animals or may damage property.

Fitting the appliance

Use the appropriate cabinet to ensure that the

appliance functions properly.

• The panels adjacent to the oven must be made of

heat-resistant material.

• Cabinets with a veneer exterior must be assembled

with glues which can withstand temperatures of up

to 100°C.

• To install the oven 

under the counter

 (

see

diagram

) and in a 

kitchen unit

, the cabinet must

have the following dimensions:

!

 The appliance must not come into contact with

electrical parts once it has been installed.

The consumption indications on the data plate have

been calculated for this type of installation.

Ventilation

To ensure good ventilation, the back panel of the

cabinet must be removed. It is advisable to install the

oven so that it rests on two strips of wood, or on a

completely flat surface with an opening of at least 45 x

560 mm (

see diagrams

).

Centring and fastening

Secure the appliance to the cabinet by opening the

oven door and putting 4 screws into the 4 holes of

the outer frame.

!

 All parts which ensure the safe operation of the

appliance must not be removable without the aid of a

tool.

595

558

 min

45

 min

575-585

 min

560

+4 -0

480

+4 -0

547 min

555

580

500

39

15

595

23

572

543

54

3

545

560 mm.

45 mm.

Installation

3

GB

Electrical connections

The cooker must be connected to the mains

electricity supply. It is designed to operate with

alternating current at the voltage and frequency

indicated on the data plate (

see the following page

).

The hob is connected to the cooker using a special

connector.

BUILT-IN HOB

BUILT-IN COOKER

WHITE

RED

YELLOW

BLUE

GREEN

Only on 

certain models

Replace the metal protection after performing all the

necessary hob connections. If the hob is removed

from its position, the red cap which was originally

protecting the red connector must be replaced.

Fitting the power supply cable

1. Open the terminal

board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(

see diagram

).

2. Install the power supply cable by loosening the

cable clamp screw and the wire contact screws L-N-

. Connect the wires to the corresponding

terminals: the Blue wire to the terminal marked (N),

the Brown wire to the terminal marked (L) and the

Yellow Green wire to the terminal marked 

.

The terminal board is designed for a 400 V three-

phase connection (

see diagrams below

).

400V 3N~H05RR-F

5x2.5 CEI-UNEL 35363

If the electrical system has other characteristics (

see

diagrams below

), carry out the electrical connection

using the connection supports provided in the box

P.

230V ~H05RR-F 3x4

CEI-UNEL 35363

400V 2N~H05RR-F 4x4

CEI-UNEL 35363

3. Secure the power supply cable by fastening the

clamp screw.

4. Close the cover of the terminal board.

N

L1

L3

L2

1

3

2

4

5

N

L2

L1

L3

P

N

L

1

3

2

4

5

N

L1 L2

1

3

2

4

5

4

GB

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (

see side

).

The appliance must be directly connected to the

mains using an omnipolar circuit-breaker with a

minimum contact opening of 3 mm installed between

the appliance and the mains, suitable for the load

indicated and complying with current electrical

regulations (the earthing wire must not be interrupted

by the circuit-breaker). The supply cable must not

come into contact with surfaces with temperatures

higher than 50°C.

!

 The installer must ensure that the correct electrical

connection has been made and that it is compliant

with safety regulations.

Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is compliant

with the law.

• The socket can withstand the maximum power of

the appliance, which is indicated on the data plate

(

see below

).

• The voltage must be in the range between the

values indicated on the data plate (

see below

).

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

!

 Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

!

 The cable must not be bent or compressed.

!

 The cable must be checked regularly and replaced

by authorised technicians only (

see Assistance

).

!

The manufacturer declines any liability should

these safety measures not be observed.

DATA PLATE 

Dimensions 

width 43.5 cm 

height 32 cm 

depth 40 cm 

Volume 

lt. 56 

Electrical 

connections 

voltage: 230V/400V~ 3N 50/60Hz 

maximum power absorbed 9450W 

ENERGY LABEL 

Directive 2002/40/EC on the label 

of electric ovens. 

Standard EN 50304 

Energy consumption for Forced 

convection heating mode:        

Multi-cooking 

Declared energy consumption for 

Natural convection Class heating 

mode:             Convection 

This appliance conforms to the 

following European Economic 

Community directives:  

- 2006/95/EEC of 12/12/06 (Low 

Voltage) and subsequent 

amendments; 

- 2004/108/EEC of 15/12/04 

(Electromagnetic Compatibility) and 

subsequent amendments; 

- 93/68/EEC of 22/07/93 and 

subsequent amendments. 

- 2002/96/EC and subsequent 

amendments. 

5

GB

Description of the appliance

Overall view

Control panel

Control panel

GRILL

DRIPPING PAN

GUIDES 

for the 

sliding racks

position 5

position 4

position 3

position 2

position 1

SELECTOR

Knob

HOTPLATES

indicator light

THERMOSTAT

indicator light

THERMOSTAT

Knob

HOTPLATES

knob

EXTENDABLE HOTPLATES

knob