Kenwood KRC-594: Connecting Wires to Terminals

Connecting Wires to Terminals: Kenwood KRC-594

Connecting Wires to Terminals

10

KENWOOD disc changer input 14

Rear left

output (White)

Antenna Cord (ISO) 1

To connect the Disc

changer, consult your

Disc changer manual. 15

Antenna Conversion Adaptor

(ISO–JASO) (Accessory3) 2

To Steering remote

REMO.CONT

(Optional accessory)

FM/AM antenna

input 3

Rear right

output (Red)

Fuse (10A)

13

4

Connector Function Guide

Wiring harness

Pin Numbers for

(Accessory1) 16

Cable Color Functions

ISO Connectors

External Power

17

TEL mute wire (Brown)

Connector

TEL MUTE

Connect to the terminal

Battery wire (Yellow) 6A

that is grounded when

A–4

Yellow

Battery

either the telephone rings

A–5

Blue/White

Power Control

or during conversation. 21

A–7

Red

Ignition (ACC)

A–8

Black

Earth (Ground)

Ignition wire (Red) 7A

To connect the

KENWOOD navigation

Connection

If no connections are made,

system, consult your

do not let the wire come out

Speaker

navigation manual. 22

from the tab. 18a

Connector

See page 280

B–1

Purple

Rear Right (+)

B–2

Purple/Black

Rear Right (–)

Power control/ Motor

B–3

Gray

Front Right (+)

antenna control wire

A–7 Pin (Red) 8

(Blue/White) 20

B–4

Gray/Black

Front Right (–)

P.CONT

Connect either to the

B–5

White

Front Left (+)

ANT.CONT

power control terminal

A–4 Pin (Yellow) 9

when using the optional

B–6

White/Black

Front Left (–)

power amplifier, or to the

B–7

Green

Rear Left (+)

8

6

4

2

Connector A

antenna control terminal in

7

5

3

1

the vehicle. 23

B–8

Green/Black

Rear Left (–)

8

6

4

2

Connector B

7

5

3

1

— 27

Connecting Wires to Terminals

2WARNING

When the connection is made as in 3 above, the unit's power will not

Connecting the ISO Connector

The pin arrangement for the ISO connectors depends on the type of

be linked to the ignition key. For that reason, always make sure to turn

vehicle you drive. Make sure to make the proper connections to

off the unit's power when the ignition is turned off.

English

prevent damage to the unit.

To link the unit's power to the ignition, connect the ignition cable

The default connection for the wiring harness is described in 1 below.

(ACC...red) to a power source that can be turned on and off with the

If the ISO connector pins are set as described in 2 or 3, make the

ignition key.

connection as illustrated.

Please be sure to reconnect the cable as shown 2 below to install

this unit to the Volkswagen vehicles etc.

1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector

is linked with the ignition, and the A-4 pin (yellow) is connected to

the constant power supply.

Unit Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

2 The A-7 pin (red) of the vehicle's ISO connector is connected to

the constant power supply, and the A-4 pin (yellow) is linked to

the ignition.

Unit Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

3 The A-4 pin (yellow) of the vehicle's ISO connector is not

connected to anything, while the A-7 pin (red) is connected to the

constant power supply (or both the A-7 (red) and A-4 (yellow) pins

are connected to the constant power supply).

Unit Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

— 28 — 28

Оглавление