Indesit KN6C61A: Installation

GB

13

!

 Before operating your new appliance please read

this instruction booklet carefully. It contains important

information concerning the safe installation and

operation of the appliance.

!

 Please keep these operating instructions for future

reference. Make sure that the instructions are kept with

the appliance if it is sold, given away or moved.

!

 The appliance must be installed by a qualified

professional in accordance with the instructions

provided.

!

 Any necessary adjustment or maintenance must be

performed after the cooker has been disconnected

from the electricity supply.

Positioning and levelling

!

 It is possible to install the appliance alongside

cupboards whose height does not exceed that of the

hob surface.

!

 Make sure that the wall in contact with the back of

the appliance is made from a non-flammable, heat-

resistant material (T 90°C).

To install the appliance correctly:

• Place it in the kitchen, the dining room or the bed-

sit (not in the bathroom).

• If the top of the hob

is higher than the

cupboards, the

appliance must be

installed at least 600

mm away from them.

• If the cooker is

installed underneath a

wall cabinet, there must

be a minimum distance

of 420 mm between this

cabinet and the top of the hob.

This distance should be increased to 700 mm if the

wall cabinets are flammable (

see figure

).

• Do not position blinds behind the cooker or less

than 200 mm away from its sides.

• Any hoods must be installed according to the

instructions listed in the relevant operating manual.

Levelling

If it is necessary to level the

appliance, screw the

adjustable feet into the places

provided on each corner of the

base of the cooker (

see figure

).

The legs* fit into the slots on

the underside of the base of

the cooker.

Electrical connection

Fitting the power supply cable

To open the terminal board:

• Insert a screwdriver into the side tabs of the

terminal board cover.

• Pull the cover to

open it.

To install the cable, follow the instructions below:

• Loosen the cable clamp screw and the wire contact

screws.

!

 The jumpers are pre-set at the Factory for 230 V

single-phase connection (

see figure

).

• To carry out the electrical connections as shown in

the figures, use the two jumpers inside the box (

see

figure

 - labelled “P”).

Installation

HOOD

420

Min.

min. 

650

 mm. with hood

min. 

700

 mm. without hood

mm.

600

Min.

mm.

420

Min.

mm.

*

 Only available in certain models.

N

L2

L1

L3

P

N

L

230V ~

H05RR-F 3x4 CEI-UNEL 35363

1

3

2

4

5

14

GB

N

L3

L1

L2

400V 3N~

H05RR-F 5x2.5 CEI-UNEL 35363

1

3

2

4

5

N

L2 L1

400V 2N~

H05RR-F 4x4 CEI-UNEL 35363

1

3

2

4

5

• Secure the power supply cable by fastening the

cable clamp screw then put the cover back on.

Connecting the supply cable to the electricity

mains

Install a standardised plug corresponding to the load

indicated on the appliance data plate (

see Technical

data table

).

The appliance must be directly connected to the

mains using an omnipolar switch with a minimum

contact opening of 3 mm installed between the

appliance and the mains.  The switch must be suitable

for the charge indicated and must comply with current

electrical regulations (the earthing wire must not be

interrupted by the switch). The supply cable must be

positioned so that it does not come into contact with

temperatures higher than 50°C at any point.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of

the appliance, which is indicated by the data plate.

• The voltage is in the range between the values

indicated on the data plate.

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

!

 Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

!

 The cable must not be bent or compressed.

! 

The cable must be checked regularly and

replaced by authorised technicians only.

!

The manufacturer declines any liability should

these safety measures not be observed.

TABLE OF CHARACTERISTICS

Oven dimensions 

(HxWxD)

32x43.5x40 cm 

Volume

56 l 

Useful measurements 

relating to the oven 

compartment

width 42 cm 

depth 44 cm 

height 8.5 cm 

Voltage and frequency

see data plate 

Ceramic hob 

Front Left 

Back Left 

Back Right 

Front Right 

Max. ceramic hob 

consumption 

1700 W 

1200 W 

2100 W 

1200 W 

6200 W 

ENERGY LABEL

Directive 2002/40/EC on the 

label of electric ovens.  

Standard EN 50304 

Energy consumption for Natural 

convection – heating mode:  

Traditional mode 

Declared energy consumption for 

Forced convection Class – 

heating mode:  

Baking. 

This appliance conforms to the 

following European Economic 

Community directives: 

2006/95/EC dated 12/12/06 (Low 

Voltage) and subsequent 

amendments - 2004/108/EC 

dated 15/12/04 (Electromagnetic 

Compatibility) and subsequent 

amendments - 93/68/EEC dated 

22/07/93 and subsequent 

amendments. 2002/96/EC 

1275/2008 (Stand-by/Off mode)