Indesit PWDE 7125 S: Installation

Installation

 This instruction manual should be kept in a safe place

Levelling the machine correctly will provide it with

GB

for future reference. If the washer-dryer is sold,

stability, help to avoid vibrations and excessive noise and

transferred or moved, make sure that the instruction

prevent it from shifting while it is operating. If it is placed

manual remains with the machine so that the new

on carpet or a rug, adjust the feet in such a way as to

owner is able to familiarise himself/herself with its

allow a sufficient ventilation space underneath the

operation and features.

washer-dryer.

 Read these instructions carefully: they contain vital

information relating to the safe installation and operation

Connecting the electricity and water

of the appliance.

supplies

Connecting the water inlet hose

Unpacking and levelling

1. Connect the inlet hose

Unpacking

by screwing it to a cold

water tab using a 3/4 gas

1. Remove the washer-dryer from its packaging.

threaded connection (see

2. Make sure that the washer-dryer has not been

figure).

damaged during the transportation process. If it has

Before performing the

been damaged, contact the retailer and do not proceed

connection, allow the

any further with the installation process.

water to run freely until it is

perfectly clear.

3. Remove the 4

protective screws (used

during transportation) and

2. Connect the inlet hose

the rubber washer with

to the washer-dryer by

the corresponding spacer,

screwing it onto the

located on the rear part of

corresponding water inlet

the appliance (see figure).

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need them

again if the washer-dryer needs to be moved to another

location.

3. Make sure that the hose is not folded over or bent.

 Packaging materials should not be used as toys for

 The water pressure at the tap must fall within the

children.

range of values indicated in the Technical data table (see

next page).

Levelling

 If the inlet hose is not long enough, contact a

1. Install the washer-dryer on a flat sturdy floor, without

specialised shop or an authorised technician.

resting it up against walls, furniture cabinets or anything

else.

 Never use second-hand hoses.

2. If the floor is not

 Use the ones supplied with the machine.

perfectly level,

compensate for any

unevenness by tightening

or loosening the adjustable

front feet (see figure); the

angle of inclination,

measured in relation to the

worktop, must not exceed

2°.

2

Connecting the drain hose

 The cable should not be bent or compressed.

GB

Connect the drain hose,

 The power supply cable must only be replaced by

without bending it, to a

authorised technicians.

drain duct or a wall drain

situated between 65 and

Warning! The company shall not be held responsible

100 cm from the floor;

in the event that these standards are not observed.

65 - 100 cm

The first wash cycle

Once the appliance has been installed, and before you

use it for the first time, run a wash cycle with

alternatively, place it

detergent and no laundry, using wash cycle number 2.

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

Technical data

same diameter as the original hose and must not

exceed 150 cm in length.

Model

PWDE 7125 S

Electrical connections

width 59,5 cm

Dimensions

height 85 cm

Before plugging the appliance into the electricity

depth 55 cm

socket, make sure that:

from 1to 7 kg for wash programme

 the socket is earthed and complies with all

Capacity

from 1 to 5 kg for the drying programme

applicable laws;

Electrical

please refer to the technical data

connections

plate fixed to the machine

 the socket is able to withstand the maximum

power load of the appliance as indicated in the

maximum pressure 1 MPa (10 bar)

Technical data table (see opposite);

Water connections

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

 the power supply voltage falls within the values

Spin speed

up to 1200 rotations per minute

indicated in the Technical data table (see opposite);

Wash: programme 2; temperature

 the socket is compatible with the plug of the

60°C; using a load of 7 kg.

Energy rated

washer-dryer. If this is not the case, replace the

Drying:

 first drying cycle performed

programmes

socket or the plug.

with a 2 kg load, by selecting the

according to

drying level "A1" (IRON);

regulation

 The washer-dryer must not be installed outdoors,

Second drying cycle performed with a

EN 50229

5 kg load, selecting the maximum

even in covered areas. It is extremely dangerous to

drying level "A4" (EXTRA).

leave the appliance exposed to rain, storms and

This appliance conforms to the

other weather conditions.

following EC Directives:

- 89/336/EEC dated 03/05/89

 When the washer-dryer has been installed, the

(Electromagnetic Compatibility) and

electricity socket must remain within easy reach.

subsequent modifications

 Do not use extension cords or multiple sockets.

- 2006/95/EC (Low Voltage)

- 2002/96/EC

3