Kenwood KDC-3657SD: INSTALLATION / CONNECTION

INSTALLATION / CONNECTION: Kenwood KDC-3657SD

Installating the unit (in-dash mounting)

Warning

The unit can only be used with a 12 V DC power supply, negative

ground.

Do the required

Disconnect the battery’s negative terminal before wiring and

wiring. (

13)

mounting.

Do not connect Battery wire (yellow) and Ignition wire (red) to the car

chassis or Ground wire (black) to prevent a short circuit.

Insulate unconnected wires with vinyl tape to prevent a short circuit.

Be sure to ground this unit to the car’s chassis again after installation.

Hook on the top side

Dashboard of

Caution

your car

Orientate the trim plate as

For safety’s sake, leave wiring and mounting to professionals. Consult

illustrated before fitting.

the car audio dealer.

Install this unit in the console of your vehicle. Do not touch the metal

parts of this unit during and shortly after use of the unit. Metal parts

Bend the appropriate tabs to hold

such as the heat sink and enclosure become hot.

the mounting sleeve firmly in place.

Do not connect the

·

wires of speaker to the car chassis, Ground wire

(black), or in parallel.

Mount the unit with the angle of 30º or less.

How to remove the unit

If your vehicle wiring harness does not have the ignition terminal,

1

Detach the faceplate.

connect Ignition wire (red) to the terminal on the vehicle’s fuse box

2 Fit the catch pin on the extraction

which provides 12 V DC power supply and is turned on and off by the

keys into the holes on both sides of

INSTALLATION / CONNECTION

ignition key.

After the unit is installed, check whether the brake lamps, blinkers,

the trim plate, then pull it out.

wipers, etc. on the car are working properly.

3 Insert the extraction keys deeply into

If the fuse blows, first make sure the wires are not touching car’s

the slots on each side, then follow

chassis, then replace the old fuse with one that has the same rating.

the arrows as shown on the right.

Basic procedure

1 Remove the key from the ignition switch, then

disconnect the · terminal of the car battery.

2 Connect the wires properly.

See Wiring connection.

(

13)

3 Install the unit to your car.

See Installing the unit (in-dash mounting).

4 Connect the · terminal of the car battery.

5 Reset the unit.

(

3)

12

EN_KDC-4757SD[E0]1.indd 12EN_KDC-4757SD[E0]1.indd 12 8/14/12 3:38:36 PM8/14/12 3:38:36 PM

Wiring connection

Part list for installation

SW FRONT

KDC

-

3657SD

KDC

-

4757SD

Subwoofer output

A

Faceplate

REAR/SW

RL

Front output

Rear/subwoofer output

REAR

RL

Rear output

( ×1 )

Fuse (10 A)

Antenna terminal

B

Mounting sleeve

( ×1 )

If no connections are made, do not let the wire come out from the tab.

C

Trim plate

Light blue/yellow

STEERING WHEEL

REMOTE INPUT

To the steering wheel remote control adapter

(Steering remote control wire)

REMOTE CONT

Blue/White

ANT CONT

( ×1 )

To the power control terminal when using the optional power amplifier, or to the antenna

(Power control wire/ Antenna control wire)

P. CONT

control terminal in the vehicle.

D

Wiring harness

Brown

To the terminal that is grounded when either the telephone rings or during conversation.

( ×1 )

(Mute control wire)

MUTE

(To connect the Kenwood navigation system, consult your navigation manual.)

E

Extraction key

Connecting the ISO connectors on some VW/

Yellow (Battery wire)

Audi or Opel (Vauxhall) automobiles

( ×2 )

Red (Ignition wire)

You may need to modify the wiring of the

supplied wiring harness as illustrated below.

Pin

Color and function

A4 Yellow : Battery

A5 Blue/White : Power control

Ignition wire

A7 Red : Ignition (ACC)

Red (A7)

(Red)

A7 (Red)

A8 Black : Earth (ground) connection

Yellow (A4)

Unit

Vehicle

B1 / B2 Purple

ª

/ Purple/black

·

: Rear speaker (right)

Battery wire

A4 (Yellow)

B3 / B4 Gray

ª

/ Gray/black

·

: Front speaker (right)

(Yellow)

ISO connectors

B5 / B6 White

ª

/ White/black

·

: Front speaker (left)

Default wiring

B7 / B8 Green

ª

/ Green/black

·

: Rear speaker (left)

ENGLISH |

13

EN_KDC-4757SD[E0]2.indd 13EN_KDC-4757SD[E0]2.indd 13 8/23/12 5:54:57 PM8/23/12 5:54:57 PM