Pioneer PDA-V100HD: Problem Possible solution
Problem Possible solution: Pioneer PDA-V100HD
Table of contents
- IMPORTANT
- VENTILATION CAUTION STANDBY/ON Button Operating Environment
- Contents
- Chapter 1 Important user information
- Chapter 2 Safety precautions
- Chapter 3 Features Supported Plasma Televisions
- Chapter 4 Supplied accessories
- Chapter 5 Part names
- Rear
- Remote control unit
- Chapter 6 Preparation Installing the unit Preparing the remote control unit
- Operating range of the remote control unit
- Chapter 7 Using the unit Operation modes Operations/Operation restrictions HDMI Control setting
- Connecting the unit to a Pioneer plasma television (see Chapter 8)
- Chapter 8 Using the unit with a Pioneer plasma television
- Chapter 9 Using the unit with other televisions
- Chapter 10 Advanced functions Connecting control cables
- Changing settings Changing HDMI output resolution Selecting the colour system Selecting the INPUT3 source signal Item Description
- Setting the video signal format Setting the audio signal when using HDMI input
- Chapter 11 Using with other components Connections to a television Connections to input components
- Using the HDMI input Connections to a HDMI- supported component About HDMI
- Connections to a component equipped with SCART connector Connections to a component with component connectors
- Chapter 12 Additional information Troubleshooting Problem Possible solution
- Problem Possible solution
- SCART pin assignments
- Specifications
- Operation of the unit’s indicators During normal operation PDP combination mode Independent 1 mode
- Independent 2 mode During setting mode When setting HDMI output resolution (when RESOLUTION button is pressed.) When setting colour system for analog signals (when COLOUR SYSTEM button is pressed.)
- When selecting INPUT 3 source signal (when SIGNAL SELECT button is pressed.) When setting HDMI video signal format (when VIDEO button is pressed.) When setting HDMI audio signal format (when AUDIO button is pressed.) Unsupported settings (when a remote control unit button not supported by currently selected input is pressed.)
Additional information
12
25
En
English
Sound is distorted.
• Replace connection cable.
• Confirm that the input component is set correctly.
Video images from analog
inputs are not displayed
properly.
Video is distorted.
• If distortion occurs in the input component’s video signal (like when performing fast
forward), depending on the video quality, some distortion may appear, or the image
may cease to appear properly.
The same symptoms may also appear depending on the performance of the television.
Also check the following settings on this unit:
• Is the colour system set properly? (See page 19.)
• If INPUT 3 is selected, is the input signal set correctly? (See page 19.)
• Is the colour format set correctly? (See page 20.)
Can’t make settings
• See the section
Changing settings
on page 19.
Remote control unit doesn’t
respond.
• Check remote control unit’s batteries; if depleted, replace with new. (See page 12.)
• If too distant from the receiver, move closer. (See page 13.)
• If an obstacle is located between the remote control unit and the signal receiver,
remove the obstacle. (See page 13.)
• If a bright fluorescent lamp or other light is shining on the remote signal sensor,
remove the light fixture farther away. (See page 13.)
Remote control unit doesn’t
respond (SR connection)
• When using SR connections, point this unit’s remote control at the signal sensor on
the plasma television to operate. When SR connections are not used, operate this
unit’s remote control while pointing it at the signal sensor on PDA-V100HD itself. (See
page 18.)
• The remote control unit will not operate when a control cable is connected to the
CONTROL IN connector. Confirm that a control cable has not been inserted to the
CONTROL IN connector. (See page 18.)
• Confirm that the connector is not connected to the connector of another
manufacturer’s component having the same function. (See page 18.)
Remote control unit doesn’t
respond (PDP combination
mode)
• During PDP combination mode (HDMI CONTROL indicator lights green),
INPUT
(
1
to
6
) buttons on this unit’s remote control are not supported. This is not a malfunction.
• When not using PDP combination mode (HDMI CONTROL indicator lights orange or
doesn’t light), the plasma television’s remote control unit cannot be used for
controlling operations.
Power ON indicator flashes
blue
• Try disconnecting the power cord from its power outlet then reconnecting it (do not
repeat this numerous times). If the symptom persists, consult your Pioneer dealer or
service station.
Even after making settings
with the remote control unit,
the corresponding indicators
don’t light.
• Are you attempting to make settings that are not supported?
Perform only those settings that are supported. (See page 19.)
Problem
Possible solution
