Kenwood KRC-31: Accessories
Accessories: Kenwood KRC-31
Accessories
External view Number of items
2WARNING
If you connect the ignition wire (red) and the battery wire (yellow)
to the car chassis (ground), you may cause a short circuit, that in
1
..........................................1
turn may start a fire. Always connect those wires to the power
source running through the fuse box.
2CAUTION
2
..........................................2
• If your car is not prepared for this special connection-system,
consult your Kenwood dealer.
• Only use antenna conversion adapters (ISO-JASO) when the
antenna cord has an ISO plug.
3
..........................................1
• Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
• If your vehicle's ignition does not have an ACC position, or if the
ignition wire is connected to a power source with constant
voltage such as a battery wire, the power will not be linked with
The use of any accessories except for those provided might result in
the ignition (i.e., it will not turn on and off along with the
damage to the unit. Make sure only to use the accessories shipped with
ignition). If you want to link the unit's power with the ignition,
the unit, as shown above.
connect the ignition wire to a power source that can be turned
on and off with the ignition key.
• If the fuse blows, first make sure that the wires have not caused
a short circuit, then replace the old fuse with one with the same
rating.
• Insulate unconnected wires with vinyl tape or other similar
Installation Procedure
material. To prevent short circuits, also do not remove the caps
1. To prevent short circuits, remove the key from the ignition and
on the ends of the unconnected wires or the terminals.
disconnect the - terminal of the battery.
• Connect the speaker wires correctly to the terminals to which
they correspond. The unit may receive damage or fail to work if
2. Make the proper input and output wire connections for each unit.
you share the - wires and/or ground them to any metal part in
3.
Cars with an ISO connector:
the car.
Connect the speaker connector of the car to Connector B of the
• When only two speakers are being connected to the system,
unit, and then connect the external power connector to
connect the connectors either to both the front output terminals
Connector A.
or to both the rear output terminals (do not mix front and rear).
Cars without an ISO connector:
For example, if you connect the + connector of the left speaker
First connect the wire of the wiring harness, and then connect
to a front output terminal, do not connect the - connector to a
the wiring harness connector to the unit.
rear output terminal.
4. Install the unit in your car.
• After the unit is installed, check whether the brake lamps,
indicators, wipers, etc. on the car are working properly.
5. Reconnect the - terminal of the battery.
• If the console has a lid, make sure to install the unit so that the
6. Press the reset button.
faceplate does not hit the lid when closing and opening.
— 23 —— 23 —
Оглавление
- CASSETTE RECEIVER
- Contents
- Safety precautions
- Safety precautions About RDS
- General features
- Tuner features General features
- RDS features
- RDS features
- Tuner features
- Tuner features
- External disc control features
- External disc control features
- Menu system
- Menu system
- Menu system
- Accessories
- Connecting Wires to Terminals
- Connecting Wires to Terminals
- Connecting Wires to Terminals Installation
- Troubleshooting Guide
- Troubleshooting Guide
- Specifications
- Cодержание
- Меры предосторожности
- Меры предосторожности O RDS
- Общие характеристики
- Cвойства тюнера Общие характеристики
- Cвойства RDS
- Cвойства RDS
- Cвойства тюнера
- Cвойства тюнера
- Функции управления внешним диском
- Функции управления внешним диском
- Система меню
- Система меню
- Система меню
- Принадлежности
- Подсоединение кабелей к гнездам для подключения
- Подсоединение кабелей к гнездам для подключения Установка
- Поиск и устранение неисправностей
- Поиск и устранение неисправностей
- Технические характеристики
- Treść
- Środki ostrożności
- Środki ostrożności Informacje o RDS
- Ogólne możliwości
- Możliwości tunera Ogólne możliwości
- Możliwości RDS
- Możliwości RDS
- Możliwości tunera
- Możliwości tunera
- Możliwości sterowania zewnętrznymi płytami
- Możliwości sterowania zewnętrznymi płytami
- Menu systemu
- Menu systemu
- Menu systemu
- Akcesoria
- Podłączanie przewodów do końcówek
- Podłączanie przewodów do końcówek Instalacja
- Przewodnik wykrywania i usuwania usterek
- Przewodnik wykrywania i usuwania usterek
- Dane techniczne
- Obsah
- Bezpečnostní pokyny
- Bezpečnostní pokyny O RDS
- Obecné funkce
- Funkce tuneru Obecné funkce
- Funkce RDS
- Funkce RDS
- Funkce tuneru
- Funkce tuneru
- Funkce ovládání externího disku
- Funkce ovládání externího disku
- Systém menu
- Systém menu
- Systém menu
- Příslušenství
- Připojování kabelů ke svorkám
- Připojování kabelů ke svorkám Instalace
- Przewodnik wykrywania i usuwania usterek
- Przewodnik wykrywania i usuwania usterek
- Specifikace