Indesit WIT 51: Installation

Installation: Indesit WIT 51

Installation

Keep this instruction manual in a safe place for

the adjustable front feet (see figure); the angle of

GB

future reference. Should the appliance be sold,

inclination, measured according to the worktop,

transferred or moved, make sure the instruction

must not exceed 2°.

manual accompanies the washing machine to inform

Levelling your appliance correctly will provide it with

the new owner as to its operation and features.

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

Read these instructions carefully: they contain vital

carpet, adjust the feet in such a way as to allow

information on installation, use and safety.

enough room for ventilation beneath the washing

machine.

Unpacking and levelling

Unpacking

Electric and water connections

1. Unpack the washing

Connecting the water inlet hose

machine.

1. Insert seal A into

2. Check whether the

the end of the inlet

washing machine has

hose and screw the

been damaged during

latter onto a cold

transport. If this is the

water tap with a 3/4

case, do not install it

A

gas threaded mouth

and contact your

(see figure).

retailer.

Before making the

connection, allow the

3. Remove the four

water to run freely

protective screws and

until it is perfectly

the rubber washer with

clear.

the respective spacer,

situated on the rear of

2. Connect the other

the appliance (see

end of the water inlet

figure).

hose to the washing

4. Seal the gaps using the plastic plugs provided.

machine,

screwing it onto the

5. Keep all the parts: you will need them again if the

appliance's cold water

washing machine needs to be moved to another

inlet, situated on the top

location.

right-hand side on the

rear of the appliance

Warning: should the screws be re-used, make sure

(see figure).

you fasten the shorter ones at the top.

3. Make sure there are no kinks or bends in the

Packaging materials are not children's toys.

hose.

Levelling

The water pressure at the tap must be within the

Your machine may make a considerable amount of

values indicated in the Technical details table

noise if the two front feet have not been adjusted

(on the next page).

correctly.

If the water inlet hose is not long enough,

1. Install the washing

contact a specialist store or an authorised

machine on a flat sturdy

serviceman.

floor, without resting it

up against walls,

furniture cabinets or

other.

2. If the floor is not

perfectly level, compen-

sate for any

unevenness by

tightening or loosening

14

Connecting the drain hose

GB

Connect the drain hose,

Do not use extensions or multiple sockets.

without bending it, to a

draining duct or a wall

The power supply cable must never be bent or

drain situated between

dangerously compressed.

65 and 100 cm from

65 - 100 cm

the floor;

The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

alternatively, place it

over the edge of a

Once the appliance has been installed, and before

basin, sink or tub,

you use it for the first time, run a wash cycle with

fastening the duct

detergent and no laundry, setting the 90°C

supplied to the tap (see

programme without a pre-wash cycle.

figure). The free end of

the hose should not be

underwater.

We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

Technical details

exceed 150 cm in length.

Model

WIT 51

Electric connection

40 cm wide

Before plugging the appliance into the mains

Dimensions

85 cm high

socket, make sure that:

60 cm deep

the socket is earthed and in compliance with the

Capacity

from 1 to 5 kg

applicable law;

Electric

voltage 220/230 Volts 50 Hz

connections

maximum absorbed power 1850 W

the socket is able to sustain the appliance's

maximum power load indicated in the Technical

maximum pressure 1 MPa (10 bar)

Water

details table (on the right);

minimum pressure 0.05 MPa (0.5 bar)

connections

drum capacity 42 litres

the supply voltage is included within the values i

Spin speed

up to 500 rpm

ndicated on the Technical details table

(on the right);

Control

programmes

programme 3; temperature 60°C;

according to

run with a load of 5 kg.

the socket is compatible with the washing

IEC456 directive

machine's plug. If this is not the case, replace

the socket or the plug.

This appliance is compliant with the

following European Community

The washing machine should not be installed in an

Directives:

- 73/23/CEE of 19/02/73 (Low

outdoor environment, not even when the area is

Voltage) and subsequent amendments

sheltered, because it may be very dangerous to

- 89/336/CEE of 03/05/89

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

leave it exposed to rain and thunderstorms.

(Electromagnetic Compatibility) and

subsequent amendments

-2002/96/CE

When the washing machine is installed, the mains

socket must be within easy reach.

15