Indesit DISP 5377: Installation

Installation

Keep this instruction manual in a safe place for

Connecting the water inlet hose

EN

future reference. If the appliance is sold, given away or

 To a suitable cold water connection point: before

moved, please ensure the manual is kept with the

attaching the hose, run the water until it is perfectly

machine, so that the new owner may benefit from the

clear so that any impurities that may be present in the

advice contained within it.

water do not clog the appliance; after performing this

operation, screw the inlet hose tightly onto a tap with

Please read this instruction manual carefully: it

a ¾ gas threaded connection.

contains important information regarding the safe

installation, use and maintenance of the appliance.

 To a suitable hot water connection point: your

dishwasher may be supplied with hot water from the

If the appliance must be moved at any time, keep it in

mains supply (if you have a central heating system

an upright position; if absolutely necessary, it may be

with radiators) provided that it does not exceed a

tilted onto its back.

temperature of 60°C.

This appliance is intended to be used in household and

Screw the hose to the tap as described for connection

similar applications such as:

to a cold water supply.

- staff kitchen areas in shops, offices and other working

If the inlet hose is not long enough, contact a

environments;

specialist store or an authorised technician (see

- farm houses;

Assistance).

- by clients in hotels, motels and other residential type

environments;

The water pressure must be within the values

- bed and breakfast type environments.

indicated in the Technical data table (see adjacent

information).

Positioning and levelling

The hose should not be bent or compressed.

1. Remove the appliance from all packaging and check

that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

Connecting the water outlet hose

proceed any further with the installation process.

Connect the outlet hose (without bending it) to a drain

duct with a minimum diameter of 4 cm.

2. Check the dishwasher by placing it so that its sides or

back panel are in contact with the adjacent cabinets or

even with the wall. This appliance can also be recessed

under a single worktop

* (see the Assembly instruction

sheet).

3. Position the dishwasher on a level and sturdy floor. If

the floor is uneven, the front feet of the appliance may be

adjusted until it reaches a horizontal position. If the

appliance is levelled correctly, it will be more stable and

much less likely to move or cause vibrations and noise

while it is operating.

4. Adjust the height of the rear foot from the front of the

The outlet hose must be at a height ranging from 40 to

appliance

* on the central lower part of the dishwasher, turning

80 cm from the floor / surface where the dishwasher

a hexagonal spanner (red color) with an opening of 8 mm in a

rests (A).

clockwise direction to increase the height or in an

Before connecting the water outlet hose to the sink

anticlockwise direction to decrease the height.

drain, remove the plastic plug (B).

Connecting the water and electricity

supplies

Connection to the water and electricity supplies

should only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water

supply network using new hoses.

Do not use old hoses.

The water inlet and outlet hoses and the electricity

supply cable may be positioned towards the right or the

* Only available in selected models.

left in order to achieve the best possible installation.

16

Anti-flooding protection

Anti-condensation strip*

EN

To ensure floods do not occur, the dishwasher:

After installing the dishwasher, open the door and stick

- is provided with a special system which blocks the

the adhesive transparent strip under the wooden shelf in

water supply in the event of anomalies or leaks from

order to protect it from any condensation which may

inside the appliance.

form.

Some models are also equipped with the supplementary

Advice regarding the first wash cycle

safety device New Acqua Stop

*, which guarantees anti-

After the appliance has been installed, immediately

flooding protection even in the event of a supply hose

before running the first wash cycle, completely fill the

rupture.

salt dispenser with water and add only then

approximately 1 kg of salt (see chapter entitled Rinse aid

WARNING: HAZARDOUS VOLTAGE!

and refined salt). The water may overflow: this is normal

and is not a cause for concern. Select the water

Under no circumstance should the water inlet hose be

hardness value (see chapter entitled Rinse aid and

cut as it contains live electrical parts.

refined salt). - After the salt has been poured into the

machine, the LOW SALT indicator light

* switches off.

Electrical connection

If the salt container is not filled, the water softener

Before inserting the plug into the electrical socket, make

and the heating element may be damaged as a result.

sure that:

 The socket is earthed and complies with current

regulations.

 The socket can withstand the maximum load of the

appliance, which is indicated on the data plate

Technical data

located on the inside of the door (see chapter entitled

width 44.5 cm

Description of the appliance).

Dimensions

height 82 cm

 The power supply voltage falls within the values

depth 57 cm

indicated on the data plate on the inside of the door.

Capacity 10 standard place-settings

 The socket is compatible with the plug of the

Water supply

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

appliance. If this is not the case, ask an authorised

pressure

7,25 – 145 psi

technician to replace the plug (see Assistance); do

Power supply

See appliance data plate

not use extension cables or multiple sockets.

voltage

Total absorbed

Once the appliance has been installed, the power

See appliance data plate

power

supply cable and the electrical socket should be easily

Fuse See appliance data plate

accessible.

This dishwasher conforms to the

The cable should not be bent or compressed.

following European Community

If the power supply cable is damaged, it must be re-

Directives:

placed by the manufacturer or its Technical Assistance

-2006/95/EC (Low Voltage

-2004/108/EC (Electromagnetic

Service in order to prevent all potential hazards. (See As-

Compatibility)

sistance)

-2005/32/EC (Comm. Reg.

The Company shall not be held responsible for any

1275/2008) (Ecodesign)

--97/17/EC (Labelling)

incidents that occur if these regulations are not

-2002/96/ EC (Waste Electrical

observed.

and Electronic Equipment WEEE)

* Only available in selected models.

17