Pioneer VSX-520-S: Problem Remedy
Problem Remedy: Pioneer VSX-520-S
Table of contents
- IMPORTANT VENTILATION CAUTION
- Operating Environment
- Contents
- Flow of settings on the receiver
- Chapter 1: Before you start
- Before you start01 Ventilation
- Chapter 2: Controls and displays
- Controls and displays02 Operating range of remote control
- Controls and displays 02 Display
- Controls and displays02
- Remote control
- Controls and displays02
- Controls and displays 02
- Chapter 3: Connecting your equipment Placing the speakers
- Hints on the speaker placement
- Connecting the speakers
- Making cable connections
- HDMI cables About HDMI Analog audio cables
- Digital audio cables About video outputs connection
- Connecting a TV and playback components Connecting using HDMI Connecting your component with no HDMI terminal
- Connecting a satellite receiver Connecting an HDD/DVD or other digital set-top box recorder, VCR and other video sources
- Using the component video jacks Connecting other audio components
- Connecting antennas
- Plugging in the receiver
- Chapter 4: Basic Setup Automatically setting up for surround sound (MCACC)
- Basic Setup04
- Chapter 5: Listening to your system Basic playback
- Auto playback Listening in surround sound
- Listening to your system 05
- Using Front Stage Surround Advance Listening in stereo
- Using Stream Direct Better sound using Phase Control Using the Sound Retriever
- Using surround back channel processing Listening with Acoustic Calibration EQ
- Setting the Audio options Setting the Up Mix function
- Setting What it does Option(s)
- Setting What it does Option(s)
- Choosing the input signal Using the headphone
- Chapter 6: The System Setup menu Using the System Setup menu Manual speaker setup
- Speaker setting
- Crossover network Channel level Speaker distance
- The Input Assign menu The Pre Out Setting
- Chapter 7 Using the tuner Listening to the radio Saving station presets
- Using the tuner07
- An introduction to RDS
- Using the tuner07 Displaying RDS information
- Chapter 8: Making recordings Making an audio or a video recording
- Chapter 9: Other connections
- Connecting Optional Bluetooth ADAPTER
- Other connections09
- Chapter 10: Additional information Troubleshooting Problem Remedy
- Problem Remedy
- Additional information 10
- HDMI Symptom Remedy
- Resetting the main unit
- Specifications Cleaning the unit
VSX-520_SYXCN_En.book 52 ページ ２０１０年４月１２日 月曜日 午後７時１３分
Additional information10
Problem Remedy
Broadcast stations cannot
• Connect an outdoor antenna (refer to page 25).
be selected automatically.
No sound from surround or
• Connect the speakers properly (refer to page 18).
center speakers.
• Refer to Speaker setting on page 40 to check the speaker settings.
• Refer to Channel level on page 41 to check the speaker levels.
No sound from subwoofer. • Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have an
LFE channel.
• Switch the subwoofer setting in Speaker setting on page 40 to YES or
PLUS.
• Switch the LFEATT (LFE Attenuate) on page 36 to LFEATT 0 or LFEATT 5.
The PHASE CONTROL
• If applicable, check that the lowpass filter switch on your subwoofer is
feature doesn’t seem to
off, or the lowpass cutoff is set to the highest frequency setting. If there is
have an audible effect.
a PHASE setting on your subwoofer, set it to 0º (or depending on the
subwoofer, the setting where you think it has the best overall effect on the
sound).
• Make sure the speaker distance setting is correct for all speakers (see
Speaker distance on page 41).
Noise during playback of a
• Move the cassette deck further from your receiver, until the noise
cassette deck.
disappears.
No sound is output or a
• Set the digital volume level of the player to full, or to the neutral
noise is output when
position.
software with DTS is played
• Make sure the player’s settings are correct and/or the DTS signal out is
back.
on. Refer to the instruction manual supplied with the DVD player.
• Set the input signal type to C1/O1/O2 (DIGITAL) (see Choosing the
input signal on page 38).
During a playback search,
• This is not a malfunction, but be sure to turn the volume down to
noise is output from a DTS
prevent the output of loud noise from your speakers.
compatible CD player.
Everything seems to be set
• Check that the positive/negative speaker terminals on the receiver are
up correctly, but the
matched with the corresponding terminals on the speakers (see
playback sound is odd.
Connecting the speakers on page 18).
Can’t operate the remote
• Replace the batteries (refer to page 10).
control.
• Operate within 7 m, 30°
of the remote sensor on the front panel (refer to
page 7).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off. • Press DIMMER on the remote control repeatedly to return to the
default.
52
En
