Pioneer VSX-520-S: Connecting the speakers
Connecting the speakers: Pioneer VSX-520-S
Table of contents
- IMPORTANT VENTILATION CAUTION
- Operating Environment
- Contents
- Flow of settings on the receiver
- Chapter 1: Before you start
- Before you start01 Ventilation
- Chapter 2: Controls and displays
- Controls and displays02 Operating range of remote control
- Controls and displays 02 Display
- Controls and displays02
- Remote control
- Controls and displays02
- Controls and displays 02
- Chapter 3: Connecting your equipment Placing the speakers
- Hints on the speaker placement
- Connecting the speakers
- Making cable connections
- HDMI cables About HDMI Analog audio cables
- Digital audio cables About video outputs connection
- Connecting a TV and playback components Connecting using HDMI Connecting your component with no HDMI terminal
- Connecting a satellite receiver Connecting an HDD/DVD or other digital set-top box recorder, VCR and other video sources
- Using the component video jacks Connecting other audio components
- Connecting antennas
- Plugging in the receiver
- Chapter 4: Basic Setup Automatically setting up for surround sound (MCACC)
- Basic Setup04
- Chapter 5: Listening to your system Basic playback
- Auto playback Listening in surround sound
- Listening to your system 05
- Using Front Stage Surround Advance Listening in stereo
- Using Stream Direct Better sound using Phase Control Using the Sound Retriever
- Using surround back channel processing Listening with Acoustic Calibration EQ
- Setting the Audio options Setting the Up Mix function
- Setting What it does Option(s)
- Setting What it does Option(s)
- Choosing the input signal Using the headphone
- Chapter 6: The System Setup menu Using the System Setup menu Manual speaker setup
- Speaker setting
- Crossover network Channel level Speaker distance
- The Input Assign menu The Pre Out Setting
- Chapter 7 Using the tuner Listening to the radio Saving station presets
- Using the tuner07
- An introduction to RDS
- Using the tuner07 Displaying RDS information
- Chapter 8: Making recordings Making an audio or a video recording
- Chapter 9: Other connections
- Connecting Optional Bluetooth ADAPTER
- Other connections09
- Chapter 10: Additional information Troubleshooting Problem Remedy
- Problem Remedy
- Additional information 10
- HDMI Symptom Remedy
- Resetting the main unit
- Specifications Cleaning the unit
Connecting your equipment03
Bare wire connections
Front speaker terminals:
Connecting the speakers
The receiver will work with just two stereo
1 Twist exposed wire strands together.
speakers (the front speakers in the diagram)
2 Loosen terminal and insert exposed wire.
but using at least three speakers is
recommended, and a complete setup is best
3 Tighten terminal.
for surround sound.
Make sure you connect the speaker on the
123
right to the right (R) terminal and the speaker
on the left to the left (L) terminal. Also make
sure the positive and negative (+/–) terminals
on the receiver match those on the speakers.
Center and surround speaker terminals:
If you’re not using a subwoofer, change the
front speaker setting (see Speaker setting on
1 Twist exposed wire strands together.
page 40) to LARGE.
2 Push open the tabs and insert exposed
Be sure to complete all connections before
wire.
connecting this unit to the AC power source.
3 Release the tabs.
18
En
10 mm
12 3
10 mm
FRONT
RL
CD-R/TAPE
DVR/VCR
SURROUND CENTER
SURR BACK /
FRONT
RL
HEIGHT
L
(
Single
)
OUT
R
PRE OUT
CD
CD-R/TAPE
DVR/VCR
L
IN IN
MONITOR OUT
DVD IN BD IN
E
SUBWOOFER
PRE OUT
SPEAKERS
A
ADAPTER PORT
AC IN
(
OUTPUT 5 V 100 mA MAX
)
VIDEO
DVR/VCR
TV/SAT
OUT IN
IN
SW
L
RSLSR
C
Powered subwoofer
Center speaker
Surround speakersFront speakers
VSX-520_SYXCN_En.book 18 ページ ２０１０年４月１２日 月曜日 午後７時１３分
