Pioneer VSX-520-S: Controls and displays 02
Controls and displays 02: Pioneer VSX-520-S
Table of contents
- IMPORTANT VENTILATION CAUTION
- Operating Environment
- Contents
- Flow of settings on the receiver
- Chapter 1: Before you start
- Before you start01 Ventilation
- Chapter 2: Controls and displays
- Controls and displays02 Operating range of remote control
- Controls and displays 02 Display
- Controls and displays02
- Remote control
- Controls and displays02
- Controls and displays 02
- Chapter 3: Connecting your equipment Placing the speakers
- Hints on the speaker placement
- Connecting the speakers
- Making cable connections
- HDMI cables About HDMI Analog audio cables
- Digital audio cables About video outputs connection
- Connecting a TV and playback components Connecting using HDMI Connecting your component with no HDMI terminal
- Connecting a satellite receiver Connecting an HDD/DVD or other digital set-top box recorder, VCR and other video sources
- Using the component video jacks Connecting other audio components
- Connecting antennas
- Plugging in the receiver
- Chapter 4: Basic Setup Automatically setting up for surround sound (MCACC)
- Basic Setup04
- Chapter 5: Listening to your system Basic playback
- Auto playback Listening in surround sound
- Listening to your system 05
- Using Front Stage Surround Advance Listening in stereo
- Using Stream Direct Better sound using Phase Control Using the Sound Retriever
- Using surround back channel processing Listening with Acoustic Calibration EQ
- Setting the Audio options Setting the Up Mix function
- Setting What it does Option(s)
- Setting What it does Option(s)
- Choosing the input signal Using the headphone
- Chapter 6: The System Setup menu Using the System Setup menu Manual speaker setup
- Speaker setting
- Crossover network Channel level Speaker distance
- The Input Assign menu The Pre Out Setting
- Chapter 7 Using the tuner Listening to the radio Saving station presets
- Using the tuner07
- An introduction to RDS
- Using the tuner07 Displaying RDS information
- Chapter 8: Making recordings Making an audio or a video recording
- Chapter 9: Other connections
- Connecting Optional Bluetooth ADAPTER
- Other connections09
- Chapter 10: Additional information Troubleshooting Problem Remedy
- Problem Remedy
- Additional information 10
- HDMI Symptom Remedy
- Resetting the main unit
- Specifications Cleaning the unit
Controls and displays 02
15
En
English
Français
Español
HDD*, DVD*, VCR*
DTV/TV*
These buttons switch between the hard
Switches between the DTV and analog TV
disk, DVD and VCR controls for HDD/DVD/
input modes for Pioneer TVs.
VCR recorders.
14
MASTER VOLUME
+/–
SB CH
Use to set the listening volume.
Press to select ON, AUTO, OFF the
15
MUTE
surround back channel.
Mutes/unmutes the sound.
CH SELECT
16
DISP
Press repeatedly to select a channel, then
Switches the display of this unit. The listening
use LEV +/– to adjust the level (page 41).
mode, sound volume, Pre Out setting or input
name can be checked by selecting an input
LEV +/–
1
source.
Use to adjust the channel levels.
17
SHIFT
MIDNIGHT
Press to access the ‘boxed’ commands (above
Switches to Midnight or Loudness
the buttons) on the remote. These buttons are
listening (page 35).
marked with an asterisk (* ) in this section.
SPEAKERS
Use to change the speaker system on or
off. When the SP OFF is selected, no sound
is output from the speakers connected to
this receiver.
DIMMER
Dims or brightens the display. The
brightness can be controlled in four steps.
12
SOURCE
Turns on or off the power of the Pioneer DVD/
DVR units when BD, DVD, DVR or CD is
selected using the MULTI CONTROL buttons.
13
TV CONTROL
buttons
These buttons can control only be used with
Pioneer TVs.
Use to turn on/off the power of the TV.
INPUT
Use to select the TV input signal.
CH +/–
Use to select channels.
VOL +/–
Use to adjust the volume on your TV.
Note
VSX-520_SYXCN_En.book 15 ページ ２０１０年４月１２日 月曜日 午後７時１３分
1 The Pre Out setting may or may not be displayed, depending on the input source you have selected.
