Indesit DFP 2727: Installation

Installation

Keep this instruction manual in a safe place for

The water inlet and outlet hoses and the electricity

EN

future reference. If the appliance is sold, given away or

supply cable may be positioned towards the right or the

moved, please ensure the manual is kept with the

left in order to achieve the best possible installation.

machine, so that the new owner may benefit from the

advice contained within it.

Connecting the water inlet hose

Please read this instruction manual carefully: it

• To a suitable cold water connection point: before

contains important information regarding the safe

attaching the hose, run the water until it is perfectly

installation, use and maintenance of the appliance.

clear so that any impurities that may be present in the

water do not clog the appliance; after performing this

If the appliance must be moved at any time, keep it

operation, screw the inlet hose tightly onto a tap with

in an upright position; if absolutely necessary, it may

a ¾ gas threaded connection.

be tilted onto its back.

• To a suitable hot water connection point: your

This appliance is intended to be used in household and

dishwasher may be supplied with hot water from the

similar applications such as:

mains supply (if you have a central heating system

- staff kitchen areas in shops, offices and other working

with radiators) provided that it does not exceed a

environments;

temperature of 60°C.

- farm houses;

Screw the hose to the tap as described for connection

- by clients in hotels, motels and other residential type

to a cold water supply.

environments;

- bed and breakfast type environments.

If the inlet hose is not long enough, contact a

specialist store or an authorised technician (

see

Positioning and levelling

Assistance

).

1. Remove the appliance from all packaging and

The water pressure must be within the values

check that it has not been damaged during

indicated in the Technical data table (

see adjacent

transportation.

information

).

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

The hose should not be bent or compressed.

2. Check the dishwasher by placing it so that its sides

or back panel are in contact with the adjacent

Connecting the water outlet hose

cabinets or even with the wall. This appliance can

Connect the outlet hose (without bending it) to a drain

also be recessed under a single worktop

* (

see the

duct with a minimum diameter of 4 cm.

Assembly instruction sheet

).

3. Position the dishwasher on a level and sturdy floor. If

the floor is uneven, the front feet of the appliance may

be adjusted until it reaches a horizontal position. If the

appliance is levelled correctly, it will be more stable

and much less likely to move or cause vibrations and

noise while it is operating.

4. Adjust the height of the rear foot from the front of the

appliance

* on the central lower part of the dishwasher,

turning a hexagonal spanner (red color) with an opening of

8 mm in a clockwise direction to increase the height or in an

The outlet hose must be at a height ranging from 40 to

anticlockwise direction to decrease the height.

80 cm from the floor / surface where the dishwasher

Connecting the water and electricity

rests (A).

Before connecting the water outlet hose to the sink

supplies

drain, remove the plastic plug (B).

Connection to the water and electricity supplies

should only be performed by a qualified technician.

The dishwasher should not stand on top of the

water hoses or the electricity supply cable.

The appliance must be connected to the water

supply network using new hoses.

Do not use old hoses.

* Only available in selected models.

16

Anti-flooding protection

Anti-condensation strip*

EN

To ensure floods do not occur, the dishwasher:

After installing the dishwasher, open the door and stick

- is provided with a special system which blocks the

the adhesive transparent strip under the wooden shelf in

water supply in the event of anomalies or leaks from

order to protect it from any condensation which may

inside the appliance.

form.

Some models are also equipped with the supplementary

safety device

New Acqua Stop

*, which guarantees anti-

Advice regarding the first wash cycle

flooding protection even in the event of a supply hose

After the appliance has been installed, immediately

rupture.

before running the first wash cycle, completely fill the

salt dispenser with water and add only then

WARNING: HAZARDOUS VOLTAGE!

approximately 1 kg of salt (

see chapter entitled Rinse aid

and refined salt

). The water may overflow: this is normal

Under no circumstance should the water inlet hose be

and is not a cause for concern. Select the water

cut as it contains live electrical parts.

hardness value (

see chapter entitled Rinse aid and

refined salt

). - After the salt has been poured into the

Electrical connection

machine, the LOW SALT indicator light

* switches off.

Before inserting the plug into the electrical socket, make

sure that:

If the salt container is not filled, the water softener

• The socket is earthed and complies with current

and the heating element may be damaged as a result.

regulations.

• The socket can withstand the maximum load of the

Technical data

appliance, which is indicated on the data plate

width 60 cm

located on the inside of the door (

see chapter entitled

Dimensions

height 85 cm

Description of the appliance

).

depth 60 cm

• The power supply voltage falls within the values

Capacity 12 standard place-settings

indicated on the data plate on the inside of the door.

Water supply

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

• The socket is compatible with the plug of the

pressure

7,25 – 145 psi

appliance. If this is not the case, ask an authorised

technician to replace the plug (

see Assistance

); do

Power supply voltage See appliance data plate

not use extension cables or multiple sockets.

Total absorbed power See appliance data plate

Once the appliance has been installed, the power

Fuse See appliance data plate

supply cable and the electrical socket should be easily

accessible.

This dishwasher conforms to the

The cable should not be bent or compressed.

following European Community

Directives:

If the power supply cable is damaged, it must be re-

-2006/95/EC (Low Voltage)

placed by the manufacturer or its Technical Assistance

-2004/108/EC (Electromagnetic

Service in order to prevent all potential hazards. (See As-

Compatibility)

-2005/32/EC (Comm. Reg.

sistance)

1275/2008) (Ecodesign)

The Company shall not be held responsible for any

-97/17/EC (Labelling)

incidents that occur if these regulations are not

-2002/96/EC (Waste Electrical

and Electronic Equipment)

observed.

(WEEE)

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal

soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even

further, only run the dishwasher when it is full.

Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W

Consumption data table for the main cycles

Standard conditions

*

User conditions

**

Energy consumption

Water consumption

Duration

Energy consumption

Water consumption

Duration

(kWh/cycle)

(l/cycle)

(min/cycle)

(kWh/cycle)

(l/cycle)

(min/cycle)

INTENSIVE

1,60 16 150 1,40 15 135

NORMAL

1,30 16 120 1,10 15 110

* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.

** Data is obtained by recording values when the appliance is operational and loaded with user crockery.

17