Indesit BWSA 61052 W: Installation

Installation

! This instruction manual should be kept in a

Levelling the machine correctly will provide

GB

safe place for future reference. If the washing

it with stability, help to avoid vibrations and

machine is sold, transferred or moved, make

excessive noise and prevent it from shifting

sure that the instruction manual remains with

while it is operating. If it is placed on carpet or

the machine so that the new owner is able to

a rug, adjust the feet in such a way as to allow

familiarise himself/herself with its operation

a sufficient ventilation space underneath the

and features.

washing machine.

! Read these instructions carefully: they con-

tain vital information relating to the safe instal-

Connecting the electricity and water

lation and operation of the appliance.

supplies

Unpacking and levelling

Connecting the water inlet hose

Unpacking

1. Insert seal A into

the end of the inlet

1. Remove the washing machine from its

hose and screw the

packaging.

latter onto a cold wa-

2. Make sure that the washing machine has

ter tap with a 3/4 gas

not been damaged during the transportation

threaded mouth (see

process. If it has been damaged, contact the

figure).

retailer and do not proceed any further with

Before making the

the installation process.

connection, allow the

3. Remove the 4 pro-

water to run freely un-

tective screws (used

til it is perfectly clear.

during transportation)

and the rubber wa-

2. Connect the inlet

sher with the cor-

hose to the washing

responding spacer,

machine by screwing

located on the rear

it onto the correspon-

part of the appliance

ding water inlet of the

(see figure).

appliance, which is

situated on the top

4. Close off the holes using the plastic plugs

right-hand side of the

provided.

rear part of the ap-

5. Keep all the parts in a safe place: you will

pliance (see figure).

need them again if the washing machine ne-

eds to be moved to another location.

3. Make sure that the hose is not folded over

! Packaging materials should not be used as

or bent.

toys for children.

! The water pressure at the tap must fall within

Levelling

the range of values indicated in the Technical

1. Install the washing machine on a flat sturdy

data table (see next page).

floor, without resting it up against walls, furni-

ture cabinets or anything else.

! If the inlet hose is not long enough, contact a

2. If the floor is not

specialised shop or an authorised technician.

perfectly level, com-

pensate for any une-

! Never use second-hand hoses.

venness by tightening

or loosening the

! Use the ones supplied with the machine.

adjustable front feet

(see figure); the angle

of inclination, measu-

red in relation to the

worktop, must not

exceed 2°.

2

Connecting the drain hose

GB

Connect the drain

hose, without bending

it, to a drain duct or

a wall drain situated

between 65 and 100

cm from the floor;

alternatively, placed

it over the edge of a

basin, sink or tub, fa-

stening the duct sup-

plied to the tap (see

figure). The free end

of the hose should

not be underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electri-

city socket, make sure that:

• thesocketisearthedandcomplieswithall

applicable laws;

• thesocketisabletowithstandthemaximum

power load of the appliance as indicated in the

Technical data table (see opposite);

• thepowersupplyvoltagefallswithintheva-

lues indicated in the Technical data table (see

opposite);

• thesocketiscompatiblewiththeplugofthe

washing machine. If this is not the case, repla-

ce the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washing machine has been instal-

led, the electricity socket must remain within

easy reach.

3

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be repla-

ced by authorised technicians.

Warning! The company shall not be held re-

sponsible in the event that these standards are

not observed.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

wash cycle “Auto Clean” (see “Cleaning the

washing machine”).

Technical data

Model

BWSA 61052

width 59.5 cm

Dimensions

height 85 cm

depth 42.5 cm

Capacity

from 1 to 6 kg

please refer to the technical

Electrical

data plate fixed to the ma-

connections

chine

maximum pressure

1 MPa (10 bar)

Water

minimum pressure

connections

0.05 MPa (0.5 bar)

drum capacity 40 litres

Spin speed

up to 1000 rotations per minute

Test wash

cycles in

accordance

Programme 9:

with re-

Eco Cotton 60°.

gulations

Programme 9:

1061/2010

Eco Cotton 40°.

and

1015/2010.

This appliance conforms to

the following EC Directives:

- EMC - 2014/30/EU (Elec-

tromagnetic Compatibility)

- LVD - 2014/35/EU (Low

Voltage)

- 2012/19/EU (WEEE)