Pioneer VSX-420-K: Problem Remedy
Problem Remedy: Pioneer VSX-420-K
Table of contents
- IMPORTANT
- Operating Environment
- Contents
- Flow of settings on the receiver
- Chapter 1: Before you start Checking what’s in the box Installing the receiver Loading the batteries
- Chapter 2: Controls and displays Front panel
- Operating range of remote control unit Display
- Controls and displays 02
- Remote control
- Controls and displays 02
- Controls and displays02
- Chapter 3: Connecting your equipment Placing the speakers
- Connecting the speakers
- Making cable connections
- About video outputs connection
- Connecting a TV and Blu-ray Disc player
- Connecting a TV and DVD player
- Connecting your component with no HDMI terminal
- Connecting an HDD/DVD recorder, VCR and other video components
- Connecting a satellite receiver Connecting the multichannel or other digital set-top box analog outputs
- Connecting other audio components Connecting to the front panel audio mini jack
- Connecting antennas
- Connecting an IR receiver Plugging in the receiver
- Chapter 4: Listening to your system Basic playback
- Choosing the input signal Auto playback Listening in surround sound
- Listening in stereo
- Using Front Stage Surround Using Stream Direct Advance Using the Sound Retriever
- Using Phase Control
- Setting the Audio options Setting What it does Option(s)
- Setting What it does Option(s)
- analog inputs Using the headphone
- Chapter 5: The System Setup menu Using the System Setup menu Manual speaker setup
- Channel level Crossover network
- Speaker Distance The Input Assign menu
- Chapter 6: Using the MULTI-ZONE feature MULTI-ZONE listening
- Using the MULTI-ZONE controls Button What it does
- Chapter Using the tuner Listening to the radio Saving station presets
- An introduction to RDS
- Displaying RDS information
- Chapter 8: Making recordings Making an audio or a video recording
- Chapter 9: Additional information Troubleshooting Problem Remedy
- Problem Remedy
- HDMI Symptom Remedy Resetting the main unit
- Specifications Cleaning the unit
VSX-420_SY_En.book 43 ページ ２０１０年３月１９日 金曜日 午前９時３７分
Additional information 09
Problem Remedy
English
Considerable noise in radio
• Connect the antenna (page 23) and adjust the position for best
broadcasts.
reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall (or connect an outdoor FM antenna).
Français
• Connect an additional internal or external AM antenna (page 23).
• Turn off equipment causing interference or move it away from the
receiver (or move antennas farther away from equipment causing
noise).
Broadcast stations cannot be
• Connect an outdoor antenna (refer to page 23).
selected automatically.
No sound from surround or
• Connect the speakers properly (refer to page 14).
center speakers.
• Refer to Speaker setting on page 33 to check the speaker settings.
• Refer to Channel level on page 34 to check the speaker levels.
No sound from subwoofer. • Make sure the subwoofer is switched on.
Italiano
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have
an LFE channel.
• Switch the subwoofer setting in Speaker setting on page 33 to YES
or PLUS.
Nederlands
• Switch the LFEATT (LFE Attenuate) on page 31 to LFEATT 0 or
LFEATT 10.
The PHASE CONTROL feature
• If applicable, check that the lowpass filter switch on your
doesn’t seem to have an
subwoofer is off, or the lowpass cutoff is set to the highest frequency
audible effect.
setting. If there is a PHASE setting on your subwoofer, set it to 0º (or
depending on the subwoofer, the setting where you think it has the
Español
best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers
(see Speaker Distance on page 35).
Noise during playback of a
• Move the cassette deck further from your receiver, until the noise
cassette deck.
disappears.
Deutsch
No sound is output or a noise
•
Make sure the player’s settings are correct and/or the DTS signal out
is output when software with
is on. Refer to the instruction manual supplied with the DVD player.
DTS is played back.
• Set the input signal type to C1/O1/O2 (DIGITAL) (see Choosing the
input signal on page 26).
During a playback search,
• This is not a malfunction, but be sure to turn the volume down to
noise is output from a DTS
prevent the output of loud noise from your speakers.
compatible CD player.
43
En
