Kenwood JK-60: English
English: Kenwood JK-60
English
before plugging in
safety
●
Make sure your electricity supply is
●
Avoid contact with steam coming
the same as the one shown on the
out of the spout area when pouring
underside of your kettle.
and out of the lid when refilling.
●
This kettle complies with European
●
Keep small children away from the
Economic Community Directive
kettle and never let the cord hang
89/336/EEC.
down over the worktop edge - a
before using for the first time
child could grab it and pull the kettle
●
Remove all packaging and any
down. If you don’t need so much
labels.
cord, shorten it by wrapping any
●
Fill to ‘MAX’, boil, then pour the
excess cord around the underside of
water away.
the base 햷.
●
Never overfill - boiling water may
key
splash out.
●
Never put the kettle, powerbase,
햲 lid release
cord or plug in liquid.
햳 on/off switch with neon
●
Do not use if there is any damage
햴 scale filter
to the kettle, powerbase, cord or
햵 water level window
plug. Get it checked or repaired: see
햶 powerbase
‘service’.
햷 cord wrap
●
This kettle is not intended for use by
young children or infirm persons
to use your jug kettle
without supervision.
1 Fill it through the spout or lid. To
●
Young children should be supervised
open the lid, push the lid release and
to ensure they do not play with the
pull the lid back.
appliance.
●
Be economical: do not boil more
●
Caution: Do not operate the kettle
water than you need.
on an inclined surface.
●
To improve the quality of your drinks
●
Only use the powerbase supplied
always use fresh water.
and keep it clean and dry.
●
Empty the kettle after each use.
●
Make sure the lid is secure before
2 Check the lid is closed.
switching the kettle on.
3 Plug in and switch on. The neon will
●
Warning: Do not open the lid while
come on.
the water is boiling.
4 Your kettle will boil and switch off
●
Take care when opening the lid -
automatically. To re-boil, wait a few
droplets of hot water may be
seconds - the on/off switch needs
ejected.
time to reset.
●
Make sure the kettle is switched off
●
Your kettle is fitted with a scale filter
before lifting or pouring.
to hold back limescale particles.
●
Remove the kettle from the base
●
If you find drops of water under your
before filling or pouring.
kettle, don’t worry - it is just
●
Never put the kettle near or on
condensation.
cooker hot plates or gas burners.
●
This kettle is for boiling water only.
●
This kettle is for domestic use only.
●
Failure to observe these cautions
may result in damage to the kettle.
2
boil-dry protection
●
Some regions of the country have
●
For safety your kettle is fitted with a
chalky water. This makes boiled
re-setable thermal fuse. If you switch
water look cloudy and leaves a
on with too little water, your kettle
deposit on the side of the kettle. This
will cut out automatically. Switch off
is normal but can be removed with
and let it cool down before re-filling.
regular cleaning.
When it has cooled down, the switch
●
Alternatively, to reduce limescale
will reset itself.
build up, use filtered water to fill your
kettle.
●
A range of Kenwood jug water filters
care and cleaning
are available.
●
Before cleaning, unplug your kettle
and let it cool down.
service and customer
the outside and powerbase
care
●
Wipe with a damp cloth, then dry.
●
Do not use abrasives - they will
If the cord is damaged it must, for
scratch the plastic surfaces.
safety reasons, be replaced by
KENWOOD or an authorised
the inside
KENWOOD repairer.
●
Even though your kettle comes with
a scale filter, you still need to clean
If you need help with:
●
the inside (and the filter) regularly.
using your kettle
●
servicing or repairs
the scale filter (where fitted)
Contact the shop where you bought
1 Push the lid release and pull the lid
your kettle.
back .
2 Gently lift out the scale filter .
3 either rinse under the tap or use a
soft brush.
or when descaling your kettle, drop
the filter in too. Rinse thoroughly.
4 To re-fit the scale filter, slide it in until
it rests on the notch under the
spout .
descaling
●
When limescale builds up on the
heating element, buy a suitable
descaler and descale your kettle.
Limescale makes your kettle take
longer to boil and can make the
element burn out. After descaling,
boil with fresh water several times
and discard. Clean any descaler off
the kettle - it can damage the parts.
3