Pioneer X-HM70-S: Additional Information

X-HM70_En.fm 27 ページ ２０１１年８月２日　火曜日　午後４時４６分

Additional Information

 Internet security software is currently installed in the

English Français Español Italiano

Additional Information

Tuner

connected component. There are cases where a component

The radio makes unusual noises continuously.

with Internet security software installed cannot be accessed.

 Is the unit placed near the TV or computer?

 The audio component on the network which has been

Troubleshooting chart

 Is the FM aerial or AM loop aerial placed properly? Move the

switched off is switched on. Switch on the audio component

on the network before switching on this receiver.

Many potential problems can be resolved by the owner

aerial away from the AC power lead if it is located nearby.

Playback does not start while ‘Please Wait’ continues to be

without calling a service technician.

displayed.

If something is wrong with this product, check the following

USB

 The component is currently disconnected from this receiver or

before calling your authorized PIONEER dealer or service

Device cannot be detected.

the power supply. Check whether the component is properly

centre.

 Is there any MP3/WMA file available?

connected to this receiver or the power supply.

 Is the device properly connected?

The PC or Internet radio is not properly operated.

General

 Is it an MTP device?

 The corresponding IP address is not properly set. Switch on

 Does the device contain AAC file only?

The clock is not set to the correct time.

the built-in DHCP server function of your router, or set up the

 Did a power failure occur?

Playback does not start.

network manually according to your network environment

 Is it a copyright protected WMA file?

(page 21).

 Reset the clock. (Refer to page 11)

 Is it a false MP3 file?

 The IP address is being automatically configured. The

Deutsch

When a button is pressed, the unit does not respond.

automatic configuration process takes time. Please wait.

 Set the unit to the power stand-by mode and then turn it back

on.

iPod and iPhone

The audio files stored on components on the network, such

as a PC, cannot be played back.

 If the unit still malfunctions, reset it. (Refer to page 29)

No sound is produced. No image appears on the TV/monitor.

 Windows Media Player 11 or Windows Media Player 12 is not

No sound is heard.

 The iPod or iPhone is not playing.

currently installed on your PC. Install Windows Media Player

 Is the volume level set to “Min”?

 The iPod or iPhone is not properly connected to the unit.

11 or Windows Media Player 12 on your PC.

 Are the headphones connected?

 Is the AC power lead of the unit plugged in?

 Audio files were recorded in formats other than MP3, WAV

 Are the speaker wires disconnected?

 The video cable is not properly connected.

(LPCM only), MPEG-4 AAC, FLAC, and WMA. Play back audio

 The TV/monitor’s input selection is not properly set.

files recorded in MP3, WAV (LPCM only), MPEG-4 AAC, FLAC,

CD player

 Audio from the iPod/iPhone cannot be heard via the

or WMA. Note that some audio files recorded in these formats

Nederlands

headphones connected to the unit.

may not be played back on this receiver.

Playback does not start.

iPod or iPhone will not charge.

 Audio files recorded in MPEG-4 AAC or FLAC are being played

Playback stops in the middle or is not performed properly.

 The iPod or iPhone is not making full contact with the

back on Windows Media Player 11 or Windows Media Player

 Is the disc loaded upside down?

connector.

12. Audio files recorded in MPEG-4 AAC or FLAC cannot be

 Does the disc satisfy the standards?

 Using iPod (3

rd

generation).

played back on Windows Media Player 11 or Windows Media

 Is the disc distorted or scratched?

Player 12. Try using another server. Refer to the operation

Playback sounds are skipped, or stopped in the middle of a

 The iPod or iPhone is not supported. Refer to Supported iPod,

manual supplied with your server.

track.

iPhone and iPad models: on page 17 for compatible models.

 The component connected to the network is not properly

 Is the unit located near excessive vibrations?

“This accessory is not made to work with iPhone” or “This

operated.

 Is the disc very dirty?

accessory is not supported by iPhone” appears on iPhone

-

Check whether the component is affected by special

 Has condensation formed inside the unit?

screen.

circumstances or is in the sleep mode.

 The iPhone battery is low. Please charge the iPhone.

-

Try rebooting the component if necessary.

 iPhone is not properly docked.

Remote control

 The component connected to the network does not permit file

sharing. Try changing the settings for the component

The remote control does not operate.

NETWORK feature

connected to the network.

 Is the AC power lead of the unit plugged in?

Cannot access the network.

 The folder stored on the component connected to the network

 Is the battery polarity correct?

has been deleted or damaged. Check the folder stored on the

 Are the batteries dead?

 The LAN cable is not firmly connected. Firmly connect the

component connected to the network.

 Is the distance or angle incorrect?

LAN cable (page 10).

 Does the remote control sensor receive strong light?

 The router is not switched on. Switch on the router.

27

En