Pioneer FH-460UI: System menu

Black plate (8,1)

Section

02

Using this unit

Using this unit

! SLA is not available when FM is selected as

3 Turn M.C. to select the system menu

Loudness compensates for deficiencies in the low-

Use this function when wanting to listen only to

the source.

function.

frequency and high-frequency ranges at low vol-

high-frequency sounds. Only frequencies higher

Once selected, the following system menu func-

ume.

than the high-pass filter (HPF) cutoff are output

FADER (fader adjustment)

tions can be adjusted.

1 Press M.C. to select the desired setting.

from the speakers.

OFF (off)—LOW (low)—MID (mid)—HI (high)

1 Press M.C. to display the setting mode.

1 Press M.C. to display the setting mode.

LANGUAGE (multi-language)

2 Press M.C. to cycle between the following:

2 Turn M.C. to adjust the front/rear speaker bal-

SUB.W (subwoofer on/off setting)

Cut-off frequency—Slope level

ance.

1 Press M.C. to select the desired setting.

This unit is equipped with a subwoofer output

3 Turn M.C. to select the desired setting.

ENG (English)—РУС (Russian)—TUR (Turk-

BALANCE (balance adjustment)

which can be turned on or off.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

ish)

1 Press M.C. to select the desired setting.

—100HZ—125HZ—160HZ—200HZ

1 Press M.C. to display the setting mode.

NOR (normal phase)—REV (reverse phase)—

Slope level: –12— –24

CLOCK SET (setting the clock)

2 Turn M.C. to adjust the left/right speaker bal-

OFF (subwoofer off)

SLA (source level adjustment)

ance.

1 Press M.C. to display the setting mode.

SUB.W CTRL (subwoofer adjustment)

This function prevents the volume from changing

2 Press M.C. to select the segment of the clock

EQ SETTING (equalizer recall)

Only frequencies lower than those in the selected

too dramatically when the source switches.

display you wish to set.

1 Press M.C. to display the setting mode.

range are outputted from the subwoofer.

! Settings are based on the FM volume level,

Hour—Minute

3 Turn M.C. to adjust the clock.

2 Turn M.C. to select the equalizer.

1 Press M.C. to display the setting mode.

which remains unchanged.

POWERFUL—NATURAL—VOCAL—CUS-

2 Press M.C. to cycle between the following:

! The MW/LW volume level can also be adjusted

12H/24H (time notation)

TOM1—CUSTOM2—FLAT—SUPER BASS

Cut-off frequency—Output level—Slope level

with this function.

Rates that can be adjusted will flash.

! USB, iPod and APP are all set to the same set-

The equalizer band and equalizer level can be

1 Press M.C. to select the desired setting.

customized when CUSTOM1 or CUSTOM2 is

3 Turn M.C. to select the desired setting.

ting automatically.

12H (12-hour clock)—24H (24-hour clock)

Cut-off frequency: 50HZ—63HZ—80HZ—

1 Press M.C. to display the setting mode.

selected.

100HZ—125HZ—160HZ—200HZ

2 Turn M.C. to adjust the source volume.

AUTO PI (auto PI seek)

If selecting CUSTOM1 or CUSTOM2, complete

the procedures outlined below. If selecting

Output level: –24 to +6

Adjustment range: +4 to –4

The unit can automatically search for a different

other options, press M.C. to return to the pre-

Slope level: –12— –24

station with the same programming, even during

vious display.

BASS BOOST (bass boost)

preset recall.

! CUSTOM1 can be set separately for each

System menu

1 Press M.C. to turn Auto PI seek on or off.

source. However, USB, iPod and APP are

1 Press M.C. to display the setting mode.

Important

AUX (auxiliary input)

all set to the same setting automatically.

2 Turn M.C. to select a desired level.

PW SAVE (power saving) is canceled if the ve-

! CUSTOM2 is a shared setting used in com-

0 to +6 is displayed as the level is increased or

Activate this setting when using an auxiliar y de-

hicle battery is disconnected and will need to be

mon for all sources.

decreased.

vice connected to this unit.

turned back on once the battery is reconnected.

3 Press M.C. to display the setting mode.

1 Press M.C. to turn AUX on or off.

4 Press M.C. to cycle between the following:

HPF SETTING (high pass filter adjustment)

When PW SAVE (power saving) is off, depend-

ing on connection methods, the unit may con-

Equalizer band—Equalizer level

DIMMER (dimmer)

tinue to draw power from the battery if your

5 Turn M.C. to select the desired setting.

vehicle’s ignition doesn’t have an ACC (acces-

1 Press M.C. to turn the dimmer on or off.

Equalizer band: 80HZ—250HZ—800HZ—

sory) position.

! You can also change the dimmer setting by

2.5KHZ—8KHZ

pressing and holding

/DIMMER.

Equalizer level: +6 to –6

1 Press M.C. to display the main menu.

MUTE MODE (mute mode)

LOUDNESS (loudness)

2 Turn M.C. to change the menu option

and press to select SYSTEM.

8

En

<QRD3247-A>8