Pioneer DEH-1600UBB: Installation DIN front/rear mount

Black plate (9,1)

Power cord

3

4

1

2

5

6

3

4

7

5

6

8

a

9

b

e

9 Blue/white

Power amp (sold separately)

! When installing, to ensure proper heat dis-

The pin position of the ISO connector will dif-

persal when using this unit, make sure you

Perform these connections when using the op-

fer depending on the type of vehicle. Connect

leave ample space behind the rear panel and

tional amplifier.

9 and b when Pin 5 is an antenna control

wrap any loose cables so they are not block-

type. In another type of vehicle, never con-

3

ing the vents.

1

nect 9 and b.

2

a Blue/white

4





Connect to system control terminal of the

55





power amp (max. 300 mA 12 V DC).

b Blue/white

1 System remote control

Connect to auto-antenna relay control termi-

Connect to Blue/white cable.

nal (max. 300 mA 12 V DC).

2 Power amp (sold separately)

c Yellow/black (DEH-1600UB, DEH-1600UBG

3 Connect with RCA cables (sold separately)

and DEH-1600UBB only)

4 To Rear output or subwoofer output

If you use an equipment with Mute function,

5 Rear speaker or subwoofer

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

c

Installation

d Speaker leads

Important

White: Front left +

White/black: Front left *

! Check all connections and systems before

1 To power cord input

Gray: Front right +

final installation.

2 Depending on the kind of vehicle, the func-

Gray/black: Front right *

! Do not use unauthorized parts as this may

tion of 3 and 5 may be different. In this

Green: Rear left + or subwoofer +

cause malfunctions.

case, be sure to connect 4 to 5 and 6 to

Green/black: Rear left * or subwoofer *

! Consult your dealer if installation requires

3.

Violet: Rear right + or subwoofer +

drilling of holes or other modifications to the

3 Yellow

Violet/black: Rear right * or subwoofer *

vehicle.

Back-up (or accessory)

e ISO connector

! Do not install this unit where:

4 Yellow

In some vehicles, the ISO connector may be

— it may interfere with operation of the vehicle.

Connect to the constant 12 V supply termi-

divided into two. In this case, be sure to con-

— it may cause injury to a passenger as a result

nal.

nect to both connectors.

of a sudden stop.

5 Red

! The semiconductor laser will be damaged if

Notes

Accessory (or back-up)

it overheats. Install this unit away from hot

! Change the initial menu of this unit. Refer to

6 Red

places such as near the heater outlet.

SP-P/O MODE (rear output and preout set-

Connect to terminal controlled by ignition

! Optimum performance is obtained when the

ting) on page 7.

switch (12 V DC).

unit is installed at an angle of less than 60°.

The subwoofer output of this unit is monau-

7 Connect leads of the same color to each

ral.

other.

60°

! When using a subwoofer of 70 W (2 W), be

8 Black (chassis ground)

sure to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and green/

black leads.

Section

Installation

Installation

03

English

Leave ample

5 cm

space

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1

2

1 Dashboard

En

9

<QRD3204-A>9