Pioneer MVH-350BT: Power cord Installation DIN front/rear mount DIN Front-mount

Hard-wired remote control adapter can be

connected (sold separately).

Power cord

3

4

1

2

5

6

3

4

7

5

6

8

a

9

b

e

9 Blue/white

Power amp (sold separately)

! Optimum performance is obtained when the

The pin position of the ISO connector will dif-

unit is installed at an angle of less than 60°.

Perform these connections when using the op-

fer depending on the type of vehicle. Connect

tional amplifier.

9 and b when Pin 5 is an antenna control

60°

type. In another type of vehicle, never con-

1

3

nect 9 and b.

2

a Blue/white

4





Connect to system control terminal of the

55

! When installing, to ensure proper heat dis-





power amp (max. 300 mA 12 V DC).

3

persal when using this unit, make sure you

b Blue/white

1

2

leave ample space behind the rear panel and

Connect to auto-antenna relay control termi-

6

wrap any loose cables so they are not block-





nal (max. 300 mA 12 V DC).

77

ing the vents.

c Yellow/black (MVH-150UI only)





If you use an equipment with Mute function,

1 System remote control

wire this lead to the Audio Mute lead on that

Connect to Blue/white cable.

equipment. If not, keep the Audio Mute lead

2 Power amp (sold separately)

free of any connections.

3 Connect with RCA cables (sold separately)

d Speaker leads

4 To Front output

White: Front left +

5 Front speaker

White/black: Front left *

6 To Rear output or subwoofer output

c

Gray: Front right +

7 Rear speaker or subwoofer

Gray/black: Front right *

Green: Rear left + or subwoofer +

Green/black: Rear left * or subwoofer *

Installation

1 To power cord input

Violet: Rear right + or subwoofer +

2 Depending on the kind of vehicle, the func-

Violet/black: Rear right * or subwoofer *

Important

tion of 3 and 5 may be different. In this

e ISO connector

! Check all connections and systems before

case, be sure to connect 4 to 5 and 6 to

In some vehicles, the ISO connector may be

final installation.

3.

divided into two. In this case, be sure to con-

! Do not use unauthorized parts as this may

3 Yellow

nect to both connectors.

cause malfunctions.

Back-up (or accessory)

! Consult your dealer if installation requires

Notes

4 Yellow

drilling of holes or other modifications to the

! Change the initial menu of this unit. Refer to

Connect to the constant 12 V supply termi-

vehicle.

SP-P/O MODE (rear output and preout set-

nal.

! Do not install this unit where:

ting) on page 12.

5 Red

— it may interfere with operation of the vehicle.

The subwoofer output of this unit is monau-

Accessory (or back-up)

— it may cause injury to a passenger as a result

ral.

6 Red

of a sudden stop.

! When using a subwoofer of 70 W (2 W), be

Connect to terminal controlled by ignition

! The semiconductor laser will be damaged if

sure to connect the subwoofer to the violet

switch (12 V DC).

it overheats. Install this unit away from hot

and violet/black leads of this unit. Do not

7 Connect leads of the same color to each

places such as near the heater outlet.

connect anything to the green and green/

other.

black leads.

8 Black (chassis ground)

Section

03

Installation

Installation

Leave ample

5 cm

space

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

14

En