Pioneer DEH-150MP: System menu

Section

02

Operating this unit

Operating this unit

! SUB.W, SUB.W CTRL and HPF SETTING are

Only frequencies lower than those in the selected

SLA (source level adjustment)

not available when REAR/REAR is selected in

1 Press M.C. to display the setting mode.

range are outputted from the subwoofer.

SP-P/O MODE. For details, refer to

2 Turn M.C. to select the equalizer.

SLA (Source level adjustment) lets you adjust the

1 Press M.C. to display the setting mode.

SP-P/O MODE (rear output and preout set-

POWERFUL—NATURAL—VOCAL—CUS-

volume level of each source to prevent radical

2 Press M.C. to cycle between the following:

ting) on the next page.

TOM1—CUSTOM2—FLAT—SUPER BASS

changes in volume when switching between sour-

Cut-off frequency—Output level—Slope level

! SUB.W CTRL and HPF SETTING are not avail-

The equalizer band and equalizer level can be

ces.

Rates that can be adjusted will flash.

able when SUB.W is selected in OFF. For de-

customized when CUSTOM1 or CUSTOM2 is

! Settings are based on the FM volume level,

3 Turn M.C. to select the desired setting.

tails, refer to SUB.W (subwoofer on/off

selected.

which remains unchanged.

Cut-off frequency: 50HZ—63HZ—80HZ—

setting) on this page.

If selecting CUSTOM1 or CUSTOM2, complete

! The MW/LW volume level can also be adjusted

100HZ—125HZ—160HZ—200HZ

the procedures outlined below. If selecting

with this function.

Output level: –24 to +6

FADER (fader adjustment)

other options, press M.C. to return to the pre-

! When selecting FM as the source, you cannot

Slope level: –6 — –12

vious display.

switch to SLA.

1 Press M.C. to display the setting mode.

! CUSTOM1 can be set separately for each

BASS BOOST (bass boost)

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the front/rear speaker bal-

source.

2 Turn M.C. to adjust the source volume.

ance.

! CUSTOM2 is a shared setting used in com-

1 Press M.C. to display the setting mode.

Adjustment range: +4 to –4

mon for all sources.

2 Turn M.C. to select a desired level.

BALANCE (balance adjustment)

3 Press M.C. to display the setting mode.

0 to +6 is displayed as the level is increased or

4 Press M.C. to cycle between the following:

decreased.

1 Press M.C. to display the setting mode.

System menu

Equalizer band—Equalizer level

2 Turn M.C. to adjust the left/right speaker bal-

HPF SETTING (high pass filter adjustment)

5 Turn M.C. to select the desired setting.

Important

ance.

Equalizer band: 80HZ—250HZ—800HZ—

When you do not want low sounds from the sub-

PW SAVE (power saving) is canceled if the ve-

EQ SETTING (equalizer recall)

2.5KHZ—8KHZ

woofer output frequency range to play from the

hicle battery is disconnected and will need to be

Equalizer level: +6 to –6

front or rear speakers, turn on the HPF (high pass

turned back on once the battery is reconnected.

! You can also switch the equalizer by pressing

filter). Only frequencies higher than those in the

When PW SAVE (power saving) is off, depend-

repeatedly.

selected range are output from the front or rear

ing on connection methods, the unit may con-

speakers.

tinue to draw power from the battery if your

LOUDNESS (loudness)

1 Press M.C. to display the setting mode.

vehicle’s ignition doesn’t have an ACC (acces-

Loudness compensates for deficiencies in the low-

2 Press M.C. to cycle between the following:

sory) position.

frequency and high-frequency ranges at low vol-

Cut-off frequency—Slope level

ume.

3 Turn M.C. to select the desired setting.

1 Press M.C. to display the main menu.

1 Press M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

OFF (off)—LOW (low)—MID (mid)—HI (high)

—100HZ—125HZ—160HZ—200HZ

2 Turn M.C. to change the menu option

Slope level: –6 — –12

and press to select SYSTEM.

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output

3 Turn M.C. to select the system menu

which can be turned on or off.

function.

1 Press M.C. to select the desired setting.

Once selected, the following system menu func-

NOR (normal phase)—REV (reverse phase)—

tions can be adjusted.

OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

6

En