Pioneer DEH-3300UB: Power cord Installation DIN front/rear mount Power amp (sold separately)

Power cord

3

4

2

5

6

1

3

4

7

5

6

8

a

9

b

e

Section

Section

03

Installation

Installation

03

English

b Blue/white

Installation

2 Secure the mounting sleeve by using a

Connect to auto-antenna relay control term-

screwdriver to bend the metal tabs (90°)

inal (max. 300 mA 12 V DC).

Important

into place.

c Yellow/black

! Check all connections and systems before

If you use an equipment with Mute function,

final installation.

1

wire this lead to the Audio Mute lead on that

! Do not use unauthorized parts as this may

equipment. If not, keep the Audio Mute lead

cause malfunctions.

free of any connections.

! Consult your dealer if installation requires dril-

d Speaker leads

ling of holes or other modifications to the vehi-

White: Front left +

cle.

2

White/black: Front left *

! Do not install this unit where:

Gray: Front right +

— it may interfere with operation of the vehi-

Gray/black: Front right *

cle.

1 Dashboard

Green: Rear left + or subwoofer +

— it may cause injury to a passenger as a re-

2 Mounting sleeve

Green/black: Rear left * or subwoofer *

sult of a sudden stop.

3 Install the unit as illustrated.

Violet: Rear right + or subwoofer +

! The semiconductor laser will be damaged if it

Violet/black: Rear right * or subwoofer *

overheats. Install this unit away from hot

1

e ISO connector

places such as near the heater outlet.

2

c

In some vehicles, the ISO connector may be

! Optimum performance is obtained when the

divided into two. In this case, be sure to con-

unit is installed at an angle of less than 60°.

nect to both connectors.

3

60°

4

1 To power cord input

Notes

2 Depending on the kind of vehicle, the function

! Change the initial setting of this unit. Refer to

of 3 and 5 may be different. In this case, be

SW CONTROL (rear output and subwoofer set-

5

sure to connect 4 to 5 and 6 to 3.

ting) on page 12.

3 Yellow

The subwoofer output of this unit is monaural.

Back-up (or accessory)

! When using a subwoofer of 70 W (2 Ω), be

DIN front/rear mount

1 Nut

4 Yellow

sure to connect the subwoofer to the violet

This unit can be properly installed using either

2 Firewall or metal support

Connect to the constant 12 V supply terminal.

and violet/black leads of this unit. Do not con-

front-mount or rear-mount installation.

3 Metal strap

5 Red

nect anything to the green and green/black

Use commercially available parts when instal-

4 Screw

Accessory (or back-up)

leads.

ling.

5 Screw (M4 × 8)

6 Red

# Make sure that the unit is installed securely in

Connect to terminal controlled by ignition

Power amp (sold separately)

DIN Front-mount

place. An unstable installation may cause skip-

switch (12 V DC).

ping or other malfunctions.

7 Connect leads of the same color to each

Perform these connections when using the

1 Insert the mounting sleeve into the

other.

optional amplifier.

dashboard.

8 Black (chassis ground)

For installation in shallow spaces, use the sup-

DIN Rear-mount

1

3

9 Blue/white

plied mounting sleeve. If there is enough

1 Determine the appropriate position

The pin position of the ISO connector will dif-

2

space, use the mounting sleeve that came

4

where the holes on the bracket and the

fer depending on the type of vehicle. Connect





with the vehicle.

side of the unit match.

9 and b when Pin 5 is an antenna control

55





type. In another type of vehicle, never connect

9 and b.

1 System remote control

a Blue/white

Connect to Blue/white cable.

Connect to system control terminal of the

2 Power amp (sold separately)

power amp (max. 300 mA 12 V DC).

3 Connect with RCA cable (sold separately)

4 To Rear output or subwoofer output

5 Rear speaker or subwoofer

16

En

En

17

<CRD4524-A/N>9