Pioneer DEH-3300UB: Initial Settings Selecting the illumination color

Section

02

Operating this unit

The cut- off frequency and output level can be ad-

3 Turn M.C. to select the initial setting.

justed when the subwoofer output is on.

After selecting, perform the following proce-

Only frequencies lower than those in the selected

dures to set the initial setting.

range are outputted from the subwoofer.

1 Press M.C. to display the setting mode.

FM STEP (FM tuning step)

2 Press M.C. to cycl e between the cut-off frequency

and output level of the subwoofer.

Normally, the FM tuning step employed by seek tun-

Cut-off frequency (Cut-off frequency display

ing is 50 kHz. When AF or TA is on, the tuning step

flashes.)—Output level (Output level display

automatically changes to 100 kHz. It may be prefer-

flashes.)

able to set the tuning step to 50 kHz when AF is on.

3 Turn M.C. to select the desired setting.

! The tuning step remains at 50 kHz during manual

Cut-off frequency: 50HZ—63HZ—80HZ—100HZ

tuning.

—125HZ

1 Press M.C. to display the setting mode.

Output level: -24 to +6

2 Turn M.C. to select the FM tuning step.

50 KHZ (50 kHz)—100 KHZ (100 kHz)

SLA (source level adjustment)

3 Press M.C. to confirm the selection.

SLA (Source Level Adjustment) lets you adjust the vo-

AUTO-PI (auto PI seek)

lume level of each source to prevent radical changes

in volume when switching between sources.

The unit can automatically search for a different sta-

! Settings are based on the FM volume level, which

tion with the same programming, even during preset

remains unchanged.

recall.

! The MW/LW volume level can also be adjusted

1 Press M.C. to turn Auto PI seek on or off.

with this function.

AUX (auxiliary input)

! When selecting FM as the source, you cannot

switch to SLA.

Activate this setting when using an auxiliary device

1 Press M.C. to display the setting mode.

connected to this unit.

2 Turn M.C. to adjust the source volume.

1 Press M.C. to turn AUX on or off.

Adjustment range: +4 to –4

USB (plug and play)

3 Press M.C. to confirm the selection.

This setting allows you to switch your source to USB/

iPod automatically.

1 Press M.C. to turn the plug and play function on

or off.

ON – When a USB storage device/iPod is con-

Initial Settings

nected, depending on the type of device, the

Important

source is automatically switched to USB/iPod

when you turn on the engine. If you disconnect

PW SAVE (power saving) is cancelled if the vehi-

your USB storage device/iPod, this unit’s source

cle battery is disconnected and will need to be

is turned off.

turned back on once the battery is reconnected.

OFF – When a USB storage device/iPod is con-

When PW SAVE (power saving) is off, depending

nected, the source is not switched to USB/iPod

on connection methods, the unit may continue to

automatically. Please change the source to USB/

draw power from the battery if your vehicle's igni-

iPod manually.

tion switch doesn't have an ACC (accessor y posi-

SW CONTROL (rear output and subwoofer setting)

tion).

1 Press and hold S (SRC/OFF) until the

unit turns off.

2 Press S (SRC/OFF) and hold until func-

tion name appears in the display.

12

En

Section

Operating this unit

02

English

The rear speaker leads output and RCA output can be

Selecting the illumination

used for full- range speaker or subwoofer connection.

color

If you switch to REAR-SP :SW, you can connect a rear

speaker lead directly to a subwoofer without using an

(Function of DEH-4300UB)

auxiliary amp.

This unit is equipped with multiple-color illu-

Initially, REAR-SP is set for rear full-range speaker

connection (FUL).

mination. You can select a desired color from

1 Press M.C. to display the setting mode.

the color list.

2 Turn M.C. to change the output and press to se-

lect.

REAR-SP—PREOUT

Direct selection from the

3 Turn M.C. to change the setting.

illumination color list

REAR-SP: FUL—SW

PREOUT: SW—REA

1 Press M.C. to display the main menu.

! Even if you change this setting, there is no

output unless you turn the subwoofer output

2 Turn M.C. to change the menu option

on (refer to SUBWOOFER1 (subwoofer on/off

and press to select ILLUMI.

setting) on page 11).

! If you change this setting, subwoo fer output

3 Turn M.C. to select the illumination

in the audio menu will return to the factory

color.

settings.

You can select one option from the following

DEMO (demo display setting)

list.

! 30 preset colors (WHITE to ROSE)

1 Press M.C. to turn the demo display on or off.

! SCAN (cycle through all colors)

SCROLL (scroll mode setting)

! CUSTOM (customized illumination color)

When ever scroll is set to ON, recorded text informa-

4 Press M.C. to confirm the selection.

tion scrolls continuously in the display. Set to OFF if

you prefer the information to scroll just once.

Notes

1 Press M.C. to turn the ever scroll on or off.

! When SCAN is selected, the illuminated color

TITLE (multi-language)

automatically cycles through the 30 preset

This unit can display the text information of a com-

colors.

pressed audio file even if they are embedded in a

! When CUSTOM is selected, the customized

Western European or Russian language.

color saved is selected.

! If the embedded language and the selected lan-

guage setting are not the same, text information

may not be displayed properly.

Customizing the illumination color

! Some characters may not be displayed properly.

1 Press M.C. to display the setting mode.

1 Press M.C. to display the main menu.

2 Turn M.C. to select the desired setting.

EUROPEAN (European)—RUSSIAN (Russian)

2 Turn M.C. to change the menu option

3 Press M.C. to confirm the selection.

and press to select ILLUMI.

PW SAVE (power saving)

3 Turn M.C. to select the preset color or

Switching this function on enables you to reduce the

CUSTOM illumination color.

consumption of battery power.

# You cannot create a custom illumination color

! Turning on the source is the only operation al-

when SCAN is selected.

lowed when this function is on.

1 Press M.C. to turn the power save on or off.

4 Press M.C. and hold until the customiz-

ing illumination color setting appears in

the display.

En

13