Pioneer A-10-K: Operation
Operation: Pioneer A-10-K
Table of contents
04 Operation
Chapter 4:
Operation
Playback
1 Turn on the power of the playback
4 Start playback of the component you
component.
selected in step 1.
2 Turn power ON to the unit.
5 Adjust playback volume with
VOLUME
• If the unit is in the standby mode, press the remote
control.
control’s STANDBY/ON button.
3 Select the source you want to playback.
6 Adjust the tone to your preference using
the
BASS
and
TREBLE
controls, and
LOUDNESS
button.
If the DIRECT button has been set to ON, these controls
are disabled.
Select the playback component.
• When using the A-30’s remote control, the INPUT
+/– button can be used to select the component.
• When using the front panel controls, rotate the
INPUT SELECTOR knob.
10
En
Music>
Extras>
iPod
Settings>
Shuffle Songs
Backlight
MENU
/I STANDBY/ON
FUNCTION
NETWORK AUDIO PLAYER
N-50
iPod/USB
5V 2.1A
STANDBY
PURE AUDIO Hi-Bit 32
62
3566
Turntable
iPod dock, etc
SACD/CD player
CD recorder or
Network audio player
tape deck
Tuner
Playback
Playback
A30_SYXE8.book 10 ページ ２０１２年２月１６日 木曜日 午前８時５８分
Set the power to Standby
When using the unit as a power amplifier
(A-30 only)
1 Press the remote control’s
STANDBY/
When a pre-amplifier is connected to the unit’s POWER
ON
button.
AMP DIRECT terminals, the unit can be used as a power
amplifier.
1 Press the
POWER AMP DIRECT
button
on the front panel of the unit.
The next time you wish to turn on the power, press the
The POWER AMP DIRECT indicator will light.
remote control’s STANDBY/ON button.
• In the case of the A-30/A-20, If the front panel’s
STANDBY/ON button is pressed, the power will
be turned off. In this case, if the power is off,
pressing the remote control’s STANDBY/ON
button will not turn on the power. To turn on the
power again, press the front panel’s STANDBY/
ON button.
Note
Caution
• If the power cord is disconnected when the unit is
• When the POWER AMP DIRECT indicator is
in the standby mode the unit will turn off, but when
lighted, operations change as follows:
the cord is then reconnected, the unit will not
– The unit’s front-panel VOLUME, BASS, TREBLE,
automatically turn on. After reconnecting the
and BALANCE controls are disabled. These
power cord, press the remote control’s
adjustments are controlled by the component
STANDBY/ON button to turn the power on.
connected to the unit’s POWER AMP DIRECT
terminals.
– When the POWER AMP DIRECT indicator is
lighted, sound volume from the A-30 will
automatically be fixed at its maximum output.
When using this unit as a power amplifier,
check the output level of the component
connected to the POWER AMP DIRECT
terminals and set it to a low level as appropriate
VOLUME
before turning on the POWER AMP DIRECT
indicator. If the sound volume of the component
connected to the POWER AMP DIRECT
terminals is initially set to a high output level,
loud sound may suddenly be output when the
POWER AMP DIRECT indicator lights.
– Sound is not produced from the PHONES jack
SACD/CD NETWORK PHONO
and RECORDER OUT terminals.
• For more information, consult the operating
TUNER AUX RECORDER
instructions for the component connected to the A-
30’s POWER AMP DIRECT terminals.
Operation 04
English
Making an audio recording
You can make an audio recording from any audio source connected to the amplifier.
Music>
iPod
Backlight
Shuffle Songs
Settings>
Extras>
MENU
/I STANDBY/ON
FUNCTION
NETWORK AUDIO PLAYER
N-50
STANDBY
iPod/USB
5V 2.1A
PURE AUDIO Hi-Bit 32
DeutschFrançais
1
Italiano Español Русский
1 Select the source you want to record.
Nederlands
2 Start recording, then start playback of
the source component.
11
En
Turntable
iPod dock, etc
SACD/CD player
Network audio player
Tuner
Playback
Recording
Audio recording component
(CD recorder, tape deck, etc.)
A30_SYXE8.book 11 ページ ２０１２年３月６日 火曜日 午前１１時１３分
To set for automatic standby status (Auto Power Down)
When this condition is set, if no input signal is detected for 30 minutes, the unit will automatically enter standby
status.
1 If the unit’s power is ON, hold the unit’s front-panel
DIRECT
button and
LOUDNESS
button depressed simultaneously for three seconds.
When this condition is set to ON, the STANDBY/APD indicator on the unit’s front panel will light green. Press the
buttons again to disable the setting.
• This condition can also be set by means of the APD button on the A-30’s remote control.
• The factory default setting is ON.
Note
• Depending on the device connected, excessive noise produced by the device may be interpreted as an audio
signal, thus preventing the Automatic Power-Down function from operating.
Restoring all the settings to the factory default settings
1 When power is in standby mode, hold the front-panel’s DIRECT button and
SACD/CD NETWORK PHONO
SPEAKERS A button depressed simultaneously for five seconds.
TUNER AUX
2 Turn power ON to the unit.
