Pioneer DEH-140UBB: Connections Turning the clock display on or off Sound muting Using an AUX source

Note

— Never wire the negative speaker cable directly

DEMO (demo display setting)

Connections

AUX cannot be selected unless the auxiliary set-

to ground.

Important

ting is turned on. For more details, refer to AUX

— Never band together negative cables of multi-

1 Press M.C. to turn the demo display on or off.

(auxiliary input) on the previous page.

! When installing this unit in a vehicle without

ple speakers.

! If PW SAVE is on, DEMO cannot be selected.

an ACC (accessory) position on the ignition

! When this unit is on, control signals are sent

SCROLL (scroll mode setting)

switch, failure to connect the red cable to the

through the blue/white cable. Connect this

Turning the clock display on

terminal that detects operation of the ignition

cable to the system remote control of an ex-

When ever scroll is set to ON, recorded text infor-

or off

key may result in battery drain.

ternal power amp or the vehicle’s auto-anten-

mation scrolls continuously in the display. Set to

na relay control terminal (max. 300 mA

OFF if you prefer the information to scroll just

% Press to turn the clock display on or

O

once.

F

F

N

12 V DC). If the vehicle is equipped with a

off.

O

S

T

glass antenna, connect it to the antenna

1 Press M.C. to turn the ever scroll on or off.

T

R

A

# The clock display disappears temporarily when

booster power supply terminal.

you perform other operations, but the clock display

TITLE (multi-language)

! Never connect the blue/white cable to the

appears again after 25 seconds.

ACC position No ACC position

power terminal of an external power amp.

This unit can display the text information of a com-

! Use of this unit in conditions other than the

Also, never connect it to the power terminal

pressed audio file even if they are embedded in a

Sound muting

following could result in fire or malfunction.

of the auto antenna. Doing so may result in

Western European or Russian language.

— Vehicles with a 12-volt battery and negative

battery drain or a malfunction.

! If the embedded language and the selected

Only for DEH-142UB, DEH-140UB and DEH-

grounding.

! The black cable is ground. Ground cables for

language setting are not the same, text infor-

140UBB.

— Speakers with 50 W (output value) and 4 ohm

this unit and other equipment (especially,

mation may not display properly.

Sound is muted automatically when:

to 8 ohm (impedance value).

high-current products such as power amps)

! Some characters may not be displayed prop-

! A call is made or received using a cell phone

! To prevent a short-circuit, overheating or mal-

must be wired separately. If they are not, an

erly.

connected to this unit.

function, be sure to follow the directions

1 Press M.C. to select the desired setting.

accidental detachment may result in a fire or

! Voice guidance is output from a connected

below.

EUR (European)—RUS (Russian)

malfunction.

Pioneer navigation unit.

— Disconnect the negative terminal of the bat-

The sound is turned off, MUTE is displayed and

PW SAVE (power saving)

tery before installation.

This unit

no audio adjustments, except volume control,

— Secure the wiring with cable clamps or adhe-

Only for DEH-142UB, DEH-140UB and DEH-

are possible. Operation returns to normal when

DEH-142UB, DEH-140UB and DEH-140UBB

sive tape. Wrap adhesive tape around wiring

140UBB.

the phone connection or the voice guidance is

that comes into contact with metal parts to

Switching this function on enables you to reduce

1

ended.

protect the wiring.

the consumption of battery power.

— Place all cables away from moving parts,

! Turning on the source is the only operation al-

lowed when this function is on.

such as the shift lever and seat rails.

1 Press M.C. to turn the power save on or off.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

Using an AUX source

compartment.

1 Insert the stereo mini plug into the AUX

— Cover any disconnected cable connectors

input jack.

with insulating tape.

— Do not shorten any cables.

2 Press SRC/OFF to select AUX as the

— Never cut the insulation of the power cable of

source.

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

2

DEH-141UB

1

Section

Operating this unit

Installation

02

03

English

2

1 Power cord input

2 Rear output

En

7