Dell Latitude D500: Display Assembly and Display Latch
Display Assembly and Display Latch : Dell Latitude D500
Back to Contents Page
Display Assembly and Display Latch
Dell™Latitude™D500ServiceManual
Display Assembly
Display Bezel
Display Panel
Display Latch
Display Assembly
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the keyboard.
3. Open the display assembly approximately 180 degrees, and support the display assembly so that it does not open past this position.
4. Loosen the captive screw that secures the display cable to the system board, and release the cable from the four cable-routing clips.
5. Pull up on the pull-tab that is attached to the display cable connector to remove the connector from the system board.
6. Remove the three M2.5 x 6-mm screws.
7. Rotate the display assembly to a 90-degree angle, and lift the display assembly up and out of the computer base.
CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
NOTICE: You must remove the display assembly before you remove the palm rest.
1
M2.5 x 6-mm screws (3)
2
display cable connector
3
display
4
computer base
5
pull-tab
6
system board connector
7
captive screw
8
cable-routing clips (4)
Display Bezel
1
display
2
computer base
1
display bumpers (6)
4
display panel
2
M2 x 5-mm screws (6)
5
top cover
3
display bezel
6
M2 x 5-mm screws (4)
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the keyboard.
3. Remove the display assembly.
4. Use a plastic scribe to pry the six display bumpers out of the screw holes located on the front of the bezel.
5. Remove the six M2 x 5-mm screws located on the front of the bezel.
6. Startingatthebottomofthedisplaypanel(bytheDELL™logo),useyourfingerstoseparatethebezelfromthetopcoverbyliftingtheinsideedgeof
the bezel away from the top cover.
Display Panel
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the keyboard.
3. Remove the display bezel.
4. Remove the two M2 x 5-mm screws from each side of the display panel.
5. Lift the display panel, and rotate the display panel out of the display cover.
6. Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector.
7. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connenctor.
Display Latch
CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
NOTICE: Carefully separate the bezel from the top cover to avoid damage to the bezel.
CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
1
top flex-cable connector
2
display connector
3
pull-tab on bottom flex-
cable connector
4
inverter connector
1. Remove the keyboard.
2. Remove the display assembly.
3. Remove the display bezel.
4. Remove the three M2 x 5-mm screws that secure the display bracket to the top cover.
5. Lift the display bracket out of the top cover, and then remove the display latch.
Back to Contents Page
NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
NOTE: Ensure that the display bracket is upright when you replace the display latch.
1
top cover
2
M2 x 5-mm screws (3)
3
display bracket
4
display latch
Оглавление
- Dell™Latitude™D500ServiceManual
- Before You Begin
- Flashing the BIOS
- Bluetooth™Card
- Microprocessor Module
- Display Assembly and Display Latch
- Docking Doors
- Fan
- Hard Drive
- Keyboard
- Base Latch
- Modem
- Palm Rest
- Pin Assignments for I/O Connectors
- Reserve Battery
- Speakers
- System Board
- System Components
- Microprocessor Thermal-Cooling Assembly
- Memory Module, Mini PCI Card, and Devices
