Главная > Мониторы > Dell > U2312HM Monitor

Dell U2312HM Monitor: инструкция

Раздел: Компьютерная техника, комплектующие, аксессуары

Тип: Монитор

Инструкция к Монитору Dell U2312HM Monitor

Dell™ U2312HM Flat Panel Monitor

User Guide

Setting the display resolution to 1920 x 1080 (maximum)

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc; Microsoft and Windows are either trademarks or registered

trademarks of Microsoft Corporation in the United States and/or other countries, Intel is a registered trademark of Intel Corporation in the U.S.

and other countries; and ATI is a trademark of Advanced Micro Devices, Inc. ENERGY STAR is a registered trademark of the U.S. Environmental

Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy

efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or

their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model U2312HMt

June 2011 Rev. A00

Dell™ U2312HM Flat Panel Monitor User's Guide

About Your Monitor

Setting Up the Monitor

Operating the Monitor

Troubleshooting

Appendix

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc; Microsoft and Windows are either trademarks or

registered trademarks of Microsoft Corporation in the United States and/or other countries, Intel is a registered trademark of Intel

Corporation in the U.S. and other countries; and ATI is a trademark of Advanced Micro Devices, Inc. ENERGY STAR is a registered

trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product

meets the ENERGY STAR guidelines for energy efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or

their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model U2312HMt

June 2011 Rev. A00

Back to Contents Page

Setting Up Your Monitor

Dell™ U2312HM Flat Panel Monitor

Setting the display resolution to 1920 x 1080 (maximum)

For maximum display performance with Microsoft

Windows

operating systems, set the display resolution to 1920 x

1080 pixels by performing the following steps:

In Windows XP:

1. Right-click on the desktop and click Properties.

2. Select the Settings tab.

3. Move the slider-bar to the right by pressing and holding the left-mouse button and adjust the screen resolution to

1920 x 1080.

4. Click OK.

In Windows Vista

or Windows

1. Right-click on the desktop and click Personalization.

2. Click Change Display Settings.

3. Move the slider-bar to the right by pressing and holding the left-mouse button and adjust the screen resolution to

1920 x 1080.

4. Click OK.

If you do not see 1920 x 1080 as an option, you may need to update your graphics driver. Please choose the scenario

below that best describes the computer system you are using, and follow the provided directions:

1: If you have a Dell™ desktop or a Dell™ portable computer with internet access.

2: If you have a non Dell™ desktop, portable computer, or graphics card.

Back to Contents Page

About Your Monitor

Dell™ U2312HM Flat Panel Monitor User's Guide

Package Contents

Product Features

Identifying Parts and Controls

Monitor Specifications

Plug and Play Capability

Universal Serial Bus (USB) Interface

LCD Monitor Quality and Pixel Policy

Maintenance Guidelines

Package Contents

Your monitor ships with the components shown below. Ensure that you have received all the components and contact Dell if something is missing.

NOTE: Some items may be optional and may not ship with your Monitor. Some features or media may not be available in certain countries.

NOTE: To set up with any other stand, please refer to the respective stand setup guide for setup instructions.

Monitor

Stand

Power Cable

VGA Cable

DVI Cable

USB up stream cable (enables the USB ports on the monitor)

Drivers and Documentation media

Quick Setup Guide

Product and Safety Information Guide

Product Features

The U2312HM flat panel display has an active matrix, Thin-Film Transistor (TFT), Liquid Crystal Display (LCD). The monitor features include:

■ 23-inch (58.42 cm) viewable area display (Measured diagonally). 1920 x 1080 resolution, plus full-screen support for lower resolutions.

■ Wide viewing angle to allow viewing from a sitting or standing position, or while moving from side-to-side.

■ Tilt, swivel, vertical extension and rotate adjustment capability. (with Enhanced Menu Rotation).

■ Removable pedestal and Video Electronics Standards Association (VESA

™) 100 mm mounting holes for flexible mounting solutions.

■ Plug and play capability if supported by your system.

■ On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.

■ Software and documentation media includes an information file (INF), Image color Matching File (ICM), PowerNap software application and product documentation.

■ Energy Saver feature for Energy Star compliance.

■ Security lock slot.

■ Asset Management Capability.

■ Capability to switch from wide aspect to standard aspect ratio while maintaining the image quality.

■ EPEAT Gold Rating.

■ Halogen Reduced.

■ Arsenic-Free glass and Mercury Free for Panel only.

■ Energy Gauge shows the energy level being consumed by the monitor in real time.

■ High Dynamic Contrast Ratio (DCR).

■ PowerNap and Dynamic Dimming Software included (comes in the CD attached with the monitor).

■ TCO Certified Displays.

Identifying Parts and Controls

Front View

Front View Front panel controls

Label Description

1 Preset Modes (default, but configurable)

2 Brightness & Contrast (default, but configurable)

3 Menu

4 Exit

5 Power (with power light indicator)

Back View

Back view Back view with monitor stand

Label Description Use

VESA mounting holes (100 mm x 100 mm

Wall mount monitor using VESA-compatible wall mount kit (100 mm x 100 mm) .

- behind attached VESA Plate)

2 Regulatory label Lists the regulatory approvals.

3 Stand release button Release stand from monitor.

4 Security lock slot Secures monitor with security cable lock.

5 Dell Soundbar mounting brackets Attaches the optional Dell Soundbar.

6 Barcode serial number label Refer to this label if you need to contact Dell for technical support.

7 USB downstream ports Connect your USB devices.

8 Cable management slot Use to organize cables by placing them through the slot.

Side View

Left view Right view

Bottom View

Bottom view Bottom view with monitor stand

Label Description Use

1 AC power cord connector Connect the power cable

2 DC power connector for Dell Soundbar. Connect the power cord for the soundbar (optional)

3 DisplayPort connector Connect your computer DP cable

4 DVI connector Connect your computer DVI cable

5 VGA connector Connect your computer VGA cable

6 USB upstream port Connect the USB cable that came with your monitor to the monitor

and the computer. Once this cable is connected, you can use the USB

connectors on the side and bottom of the monitor

7 USB downstream ports Connect your USB devices. You can only use this connector after you

have connected the USB cable to the computer and USB upstream

connector on the monitor.

8 Stand lock feature To lock the stand to the monitor using M3x6 mm machine screw

(screw not provided)

Monitor Specifications

Flat Panel Specifications

Screen type Active matrix - TFT LCD

Panel type IPS

Screen dimensions 23 inches (23-inches viewable image size)

Preset display area: 509.2 (H) X 286.4 (V) mm

Horizontal 509.2 mm (20.05 inches)

Vertical 286.4 mm (11.28 inches)

Pixel pitch 0.265 mm

178° (vertical) typical

Viewing angle

178° (horizontal) typical

Luminance output 300 cd/m²(typical)

Contrast ratio 1000 to 1 (typical), 2M : 1 (typical Dynamic Contrast On)

Faceplate coating Antiglare with hard-coating 3H

Backlight LED edgelight system

Response Time 8 ms gray-to-gray (typical)

Color depth 16.7 million colors

Color Gamut 82%*

*[U2312HM] color gamut (typical) is based on CIE1976 (82%) and CIE1931 (72%) test standards.

Resolution Specifications

Horizontal scan range 30 kHz to 83 kHz (automatic)

Vertical scan range 56 Hz to 76 Hz (automatic)

Maximum preset resolution 1920 x 1080 at 60 Hz

Supported Video Modes

Video display capabilities (DVI & DP playback) 480p, 576p, 720p, 1080p, 480i, 576i, 1080i

Preset Display Modes

Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal/Vertical)

VESA, 720 x 400 31.5 70.0 28.3 -/+

VESA, 640 x 480 31.5 60.0 25.2 -/-

VESA, 640 x 480 37.5 75.0 31.5 -/-

VESA, 800 x 600 37.9 60.0 40.0 +/+

VESA, 800 x 600 46.9 75.0 49.5 +/+

VESA, 1024 x 768 48.4 60.0 65.0 -/-

VESA, 1024 x 768 60.0 75.0 78.8 +/+

VESA, 1152 x 864 67.5 75.0 108.0 +/+

VESA, 1280 x 1024 64.0 60.0 108.0 +/+

VESA, 1280 x 1024 80.0 75.0 135.0 +/+

VESA, 1920 x 1080 67.5 60.0 148.5 +/+

Electrical Specifications

Analog RGB, 0.7 Volts +/- 5%, positive polarity at 75 ohm input impedance

Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50 ohm

Video input signals

input impedance

DP 1.1a signal input support

TTL levels required and separate syncs (including Trigger points), SOG (Composite

Synchronization input signals

SYNC on green)

AC input

100 to 240 VAC / 50 or 60 Hz +

3 Hz / 1.5 A (Typical)

voltage/frequency/current

120 V : 30 A (Max)

Inrush current

240 V : 60 A (Max)

Physical Characteristics

Connector type 15-pin D-subminiature, blue connector; DVI-D, white connector;

DP, black connector.

Signal cable type Digital: Detachable, DVI-D, Solid pins, shipped detached from the

monitor

Analog: attachable, D-Sub, 15pins, shipped detached from the

monitor

Dimensions (with stand)

Height (extended) 493.9 mm (19.44 inches)

Height (compressed) 365.0 mm (14.37 inches)

Width 546.4 mm (21.51 inches)

Depth 185.4 mm (7.30 inches)

Dimensions (without stand)

Height 323.3 mm (12.73 inches)

Width 546.4 mm (21.51 inches)

Depth 59.5 mm (2.34 inches)

Stand dimensions

Height (extended) 401.2 mm (15.80 inches)

Height (compressed) 358.1 mm (14.10 inches)

Width 279.8 mm (11.02 inches)

Depth 180.3 mm (7.10 inches)

Weight

Weight with packaging 6.47 kg (14.26 lbs)

Weight with stand assembly and

5.18 kg (11.42 lbs)

cables

Weight without stand assembly 2.96 kg (6.53 lbs)

(For wall mount or VESA mount

considerations - no cables)

Weight of stand assembly 1.72 kg (3.79 lbs)

Front Frame Gloss 5.0 gloss unit (max.) (Black Frame)

20.0 gloss unit (max.) (Silver Frame)

Environmental Characteristics

Temperature

Operating 0 °C to 40 °C

Storage: -20 °C to 60 °C (-4 °F to 140 °F)

Non-operating

Shipping: -20 °C to 60 °C (-4 °F to 140 °F)

Humidity

Operating 10% to 80% (non-condensing)

Storage: 5% to 90% (non-condensing)

Non-operating

Shipping: 5% to 90% (non-condensing)

Altitude

Operating 3,048 m (10,000 ft) max

Non-operating 10,668 m (35,000 ft) max

238.85 BTU/hour (maximum)

Thermal dissipation

102.36 BTU/hour (typical)

Power Management Modes

If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to

as Power Save Mode*. If the computer detects input from keyboard, mouse, or other input devices, the monitor automatically resumes functioning. The following table shows the

power consumption and signaling of this automatic power saving feature:

VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consumption

Normal operation Active Active Active Blue 70W (maximum) **

30W (typical)

Active-off mode Inactive Inactive Blanked Amber Less than 0.5 W

Switch off - - - Off Less than 0.5 W

The OSD will only function in the normal operation mode. When any button is pressed in Active-off mode, one of the following messages will be displayed:

Activate the computer and the monitor to gain access to the OSD.

NOTE: This monitor is ENERGY STAR

-compliant.

* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.

** Maximum power consumption with max luminance, Dell Soundbar, and USB active.

Pin Assignments

VGA Connector

15-pin Side of the Connected Signal Cable

Number

1 Video-Red

2 Video-Green

3 Video-Blue

4 GND

5 Self-test

6 GND-R

7 GND-G

8 GND-B

9 Computer 5V/3.3V

10 GND-sync

11 GND

12 DDC data

13 H-sync

14 V-sync

15 DDC clock

DVI Connector

24-pin Side of the Connected Signal Cable

Number

1 TMDS RX2-

2 TMDS RX2+

3 TMDS Ground

4 Floating

5 Floating

6 DDC Clock

7 DDC Data

8 Floating

9 TMDS RX1-

10 TMDS RX1+

11 TMDS Ground

12 Floating

13 Floating

14 +5V/+3.3V power

15 Self test

16 Hot Plug Detect

17 TMDS RX0-

18 TMDS RX0+

19 TMDS Ground

20 Floating

21 Floating

22 TMDS Ground

23 TMDS Clock+

24 TMDS Clock-

DisplayPort Connector

20-pin Side of the Connected Signal Cable

Number

1 ML0(p)

2 GND

3 ML0(n)

4 ML1(p)

5 GND

6 ML1(n)

7 ML2(p)

8 GND

9 ML2(n)

10 ML3(p)

11 GND

12 ML3(n)

13 GND

14 GND

15 AUX(p)

16 GND

17 AUX(n)

18 HPD

DP_PWR Return

+3.3V DP_PWR

Plug and Play Capability

You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID)

using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. Most monitor installations are automatic; you can select different

settings if desired. For more information about changing the monitor settings, see Operating the Monitor

Universal Serial Bus (USB) Interface

This section gives you information about the USB ports that are available on the left side of your monitor.

NOTE: This monitor supports High-Speed Certified USB 2.0 interface.

Transfer speed Data

Power Consumption

Rate

High speed 480 Mbps 2.5W (Max., each port)

Full speed 12 Mbps 2.5W (Max., each port)

Low speed 1.5 Mbps 2.5W (Max., each port)

USB Upstream Connector

Pin Number 4-pin Side of the Connector

DMU

2 VCC

DPU

GND

USB Downstream Connector

Pin Number 4-Pin Side of the Signal Cable

VCC

DMD

DPD

GND

USB Ports

1 upstream - back

4 downstream - 2 on back; 2 on left side

NOTE: USB 2.0 functionality requires a USB 2.0-capable computer

NOTE: The monitor's USB interface works only when the monitor is on or in power save mode. If you turn off the monitor and then turn it on, the attached peripherals may take

a few seconds to resume normal functionality.

LCD Monitor Quality and Pixel Policy

During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state which are hard to see and do not affect the

display quality or usability. For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at: support.dell.com.

Maintenance Guidelines

Cleaning Your Monitor

WARNING: Read and follow the safety instructions before cleaning the monitor.

WARNING: Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.

For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:

To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic coating. Do

not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.

Use a lightly-dampened, warm cloth to clean the monitor. Avoid using detergent of any kind as some detergents leave a milky film on the monitor.

If you notice white powder when you unpack your monitor, wipe it off with a cloth.

Handle your monitor with care as a darker-colored monitor may scratch and show white scuff marks more than a lighter-colored monitor.

To help maintain the best image quality on your monitor, use a dynamically changing screen saver and turn off your monitor when not in use.

Back to Contents Page

Setting Up the Monitor

Dell™ U2312HM Flat Panel Monitor User's Guide

Attaching the Stand

Connecting the Monitor

Organizing Your Cables

Attaching the Soundbar (optional)

Removing the Stand

Wall Mounting (Optional)

Attaching the Stand

NOTE: The stand is detached when the monitor is shipped from the factory.

NOTE: This is applicable for a monitor with a stand. When any other stand is bought, please refer to the respective stand setup guide for set up

instructions.

To attach the monitor stand:

1. Remove the cover and place the monitor on it.

2. Fit the two tabs on the upper part of the stand to the groove on the back of the monitor.

3. Press the stand till it snaps into its place.

Connecting Your Monitor

WARNING: Before you begin any of the procedures in this section, follow the Safety Instructions.

To connect your monitor to the computer:

1. Turn off your computer and disconnect the power cable.

Connect the blue (VGA) cable from your monitor to your computer.

NOTE: If your computer supports a white DVI connector, unscrew and detach the blue (VGA) cable from the monitor and then connect

the White DVI cable to the monitor and the white DVI connector on your computer.

NOTE: Do not connect the blue VGA, the white DVI, or the black DisplayPort cables to the computer at the same time.

2. Connect the white (digital DVI-D) or the blue (analog VGA) or the black (DisplayPort) display connector cable to the corresponding video port on the back of your

computer. Do not use the three cables on the same computer. Use all the cables only when they are connected to three different computers with appropriate video

systems.

Connecting the white DVI cable