Asus P2-P5945GC: инструкция

English

P-Series

ASUS PC (Desktop Barebone)

Installation manual

Download the latest manual from the ASUS website: www.asus.com

Front/Rear panel features

P1 Front (Close)

P2 Front (Close)

Front (Open)

Rear

English

1

11

12

8

2

2

3

9

3

4

7

4

1

13

5

5

14

6

6

10

1. Optical drive eject button ( )

11. Power connector

12.** Voltage selector switch

2. HDD LED (

)

3. Optical drive bay cover

13.* • PS/2 keyboard port (

)

4. Open the front panel cover (

)

• PS/2 mouse port (

)

• VGA port (

)

5. Power button ( )

• HDMI port (

)

6. Power LED (

)

• Parallel port (

)

7. Front panel cover

8. Reset button (

)

• USB 2.0 ports (

)

9.* • MS/MS Pro card slot (

)

• LAN (RJ-45) port (

)

• CF card slot (

)

• Serial (COM1) port (

)

• SD/MMC card slot (

)

• DVI-D port (

)

• MS/MS Pro/SD/MMC card slot (

)

• Optical S/PDIF Out port (

)

• 6-pin IEEE 1394a port (

)

• Coaxial S/PDIF Out port (

)

• S/PDIF In port (

)

• IEEE 1394a port (

)

10.* • 4-pin IEEE 1394a port (

)

 •Audioportscongurations:

• USB 2.0 ports (

)

• 6-channel

• Headphone port (

)

• 8-channel

• Microphone port (

)

14. Expansion slot metal brackets

NOTE: *The front/rear panel slots/ports and their locations may vary, depending on the

model of your system. For detailed descriptions, refer to the system User Guide.

NOTE: **The system’s power supply unit has a 115V / 230V voltage selector switch

located beside the power connector. Use this switch to select the appropriate system

input voltage according to the voltage supply in your area.

2 Installation manual

Internal components

3

2

English

1

4

5

7

6

1. Front panel cover

4. PCI card riser bracket (connected

2. 5.25-inch optical drive and

to the motherboard PCI slot)

3.5-inch hard disk drive cage

5. ASUS motherboard*

3. Power supply unit

6. DIMM sockets

7. CPU fan

NOTE: *Refer to the system User Guide for motherboard details.

Removing the cover

1. Remove the cover screws on the rear panel. Keep the screws for later use.

2. Pull the cover toward the rear panel.

3. Lift the cover, then set it aside.

2

3

Removing the front panel cover

1. Locate the front

panel cover hooks,

then lift them until

they disengage from

the chasis.

2. Swing the front panel

cover to the right,

remove it, and set it

aside.

3Installation manual

1

1

2

Removing the storage drive assembly

1. Lay the system on its side, then

English

locate and remove three storage

drive assembly screws.

2. Lift the storage drive assembly, then

set aside.

Removing the CPU fan and heatsink assembly

®

Removing an Intel

CPU fan and heatsink assembly

1. Disconnect the CPU fan cable from

the connector on the motherboard.

2. Loosen the four screws out of the

fan holes to disengage the fan

and heatsink assembly from the

motherboard.

3. Carefully remove the fan and

heatsink assembly, then set it aside.

Removing an AMD CPU fan and heatsink assembly

1. Remove two screws securing the blower to the CPU fan.

2. Carefully lift each locking lever and detach its end

from the hole of the retention module.

3. Release the hook of each metal clip from the hole

of the retention module.

4. Remove the metal clips from the side rail of the

fan and heatsink assembly.

5. Disconnect the CPU fan cable from the connector

on the motherboard, then remove the fan and

heatsink assembly.

4 Installation manual

2

1

1

1

3

2

1

Locking

2

Metal clip

levers

5

4

3

Hook

Retention module

Installing a CPU

®

Installing an Intel

CPU in the LGA775 package

Retention tab

1. Locate the CPU socket on the motherboard.

2. Press the load lever with your thumb

2A

(2A), then move it to the left (2B) until it is

English

released from the retention tab.

2B

3. Lift the load lever in the direction of the

Load lever

arrow to a 135º angle.

4. Lifttheloadplatewithyourthumbandforengertoa100ºangle(4A),then

push the PnP cap from the load plate window to remove (4B).

5. Position the CPU over the socket, making sure that the gold triangle is on the

bottom-left corner of the socket. Fit the socket alignment key into the CPU

notch.

6. Close the load plate (6A), then push the load lever (6B) until it snaps into the

retention tab.

PnP cap

6A

Load plate

Gold

4B

4A

triangle

mark

5

3

6B

Alignment key

Installing an AMD CPU

1. Locate the CPU socket, then lift the socket lever to a 90º angle.

2. Install the CPU to the socket, making sure that the CPU corner with the gold

triangle matches the socket corner with a small triangle.

3. Push down the socket lever to secure the CPU.

1 2

3

®

NOTE: To reinstall an Intel

/ AMD CPU fan and heatsink assembly, follow the

instructions on page 4 in reverse order.

CAUTION: After you reinstall a fan and heatsink assembly, do not forget to connect

the CPU fan connector! Hardware monitoring error can occur if you fail to plug this

connector.

5Installation manual

Installing a DIMM

1. Locate the DIMM sockets in the motherboard.

English

2. Unlock a DIMM socket by pressing the retaining clips outward.

3. Align a DIMM on the socket such that the notch on the DIMM matches the

break on the socket.

4. Push the DIMM to the socket until the retaining clips snap inward.

4

2

3

CAUTION:

• Unplug the power supply before adding or removing DIMMs. Failure to do so may

cause damage to the motherboard and/or components.

 • ADDRDIMMiskeyedwithanotchsothatittsinonlyonedirection.Donotforce

a DIMM into a socket to avoid damaging the DIMM.

Installing an expansion card

1. Lift the PCI riser card assembly to

2. Remove the metal cover opposite

remove.

the slot that you intend to use.

3. Insert the card connector to the

4. Reinstall the PCI riser card

slot,thenpressthecardrmly

assembly. Make sure that the

untilittsinplace.Securethe

riser card connector sits properly

card with a screw.

on the motherboard PCI slot.

6 Installation manual

Installing optical and storage drives

1. Turn the storage drive assembly upside down with the 3.5-inch bay on top of

the 5.25-inch bay.

2. Insert the optical drive upside down to the 5.25-inch bay, then secure it with

two screws on both sides.

English

3. Turn the storage drive assembly, insert the hard disk drive upside down to the

3.5-inch bay, then secure it with two screws on both sides.

2

3

Reinstalling the storage drive assembly

1. Connect the IDE (1A) and power (1B) plugs to connectors at the back of the

optical drive.

2. Connect the SATA/IDE (2A) and power (2B) plugs to the connectors at the

back of the SATA/IDE hard disk drives.

3. Install the storage drive assembly to the chassis.

4. Secure the storage drive assembly with three screws.

SATA

IDE

1B

2B

2A

1A

2B

2A

7Installation manual

3

4

Installing the foot stand

1. Insert the foot stand hooks into

2. Pull the foot stand to the direction

English

the holes on the chassis.

of the arrow until the lock snaps

in place.

NOTE: To remove the foot stand, lift the lock, then slightly push the foot stand to the

direction of the rear panel until it disengages from the chassis.

Reinstalling the front panel cover

Reinstalling the cover

1. Insertthecovertothechasis.Makesurethecovertabstthechasisrails.

2. Pushthecovertowardthefrontpaneluntilittsinplace.

3. Secure the cover with two screws you removed earlier.

NOTE: Refer to the pictures in the section “Removing the cover” on page 3 in reverse

order.

NOTE: For P2 model, if your optical

drive tray fails to eject when you press

the eject button, attach the provided

sticker to the location shown at the back

of the front panel cover. Make sure the

sticker aligns with the optical drive eject

button.

8 Installation manual

1. Insert the front panel

cover tabs to the holes

on the right side of the

chassis, then swing

1

2

the front panel cover to

the left.

2. Insert the front panel

cover hooks to the

chassis until the front

panelcovertsin

place.

Sticker