Asus V2-P5G31: инструкция

English

V-Series

ASUS PC (Desktop Barebone)

Installation manual

Front panel features

1. 5.25-inch drive

bay cover

2. 3.5-inch drive bay

1

1

cover

3. Headphone port

4. Microphone port

2

2

5. USB 2.0 ports*

6. HDD LED

7. Power button

8. Reset button

4

6

4

6

NOTE: *Some models

5

5

7

may have two additional

3

3

8

8

USB 2.0 ports and/or one

IEEE 1394a port.

7

Rear panel features

NOTE: The rear panel ports and their locations

may vary, depending on the model of your

system. For detailed descriptions, refer to the

system User Guide.

1. PS/2 keyboard port ( )

2. PS/2 mouse port (

)

1

2

3. VGA port (

)

4. Parallel port (

)

7

4

5. USB 2.0 ports (

)

(some models may

3

have four rear USB 2.0 ports)

8

5

6

6. LAN (RJ-45) port ( )

7. One of the following ports:

9

• E-SATA port (

)

• Serial (COM1) port (

)

• DVI port (

)

• Optical S/PDIF Out port (

)

• Coaxial S/PDIF Out port (

)

8. IEEE 1394a port (

)

(some models

only)

9. Oneofthefollowingaudioportscongurations:

• 6-channel

• 8-channel

 RefertothecongurationtableintheUserGuidefordetails.

Internal components

5

2

3

4

1

6

7

8

1. Front panel cover

5. Power supply unit

2. 5.25-inch optical drive bays

6. Chassis fan slot

3. Floppy disk drive bay

7. ASUS motherboard*

4. Hard disk drive bay

8. Expansion slot metal brackets

NOTE: *Refer to the system User Guide for motherboard details.

Selecting the voltage

The system’s power supply unit has a 115

V/230 V voltage selector switch located

beside the power connector. Use this

switch to select the appropriate system

input voltage according to the voltage

supply in your area.

If the voltage supply in your area is

100-127 V, set the switch to 115 V.

If the voltage supply in your area is

200-240 V, set the switch to 230 V.

NOTE: Refer to the system User Guide for the exact location of the voltage selector.

Removing the side cover and

front panel assembly

1. Remove the cover screws on the rear panel.

2. Pull the side cover toward the rear panel until its hooks disengage from the

chassis tab holes. Set the side cover aside.

3. Locate the front panel assembly hooks, then lift them until they disengage

from the chassis.

4. Swing the front panel assembly to the right, until the hinge-like tabs on the

right side of the assembly are exposed.

5. Remove the front panel assembly, then set aside.

4

3

Air duct

1

4

3

2

1

4

3

2

Chassis tab holes

3

Installing a CPU

®

®

Installing an Intel

Pentium

4 CPU in the LGA775 package

1. Locate the CPU socket on the motherboard.

2. Press the load lever with your thumb

Retention tab

(A), then move it to the left (B) until it

is released from the retention tab.

A

CAUTION. To prevent damage to

B

the socket pins, do not remove the

PnP cap unless you are installing

a CPU.

Load lever

3. Lift the load lever in the direction of the arrow to

PnP cap

a 135º angle.

Load plate

4. Lift the load plate with your thumb and

4B

forengertoa100ºangle(4A),thenpushthe

4A

PnP cap from the load plate window to remove

(4B).

3

5. Position the CPU over the socket, making

sure that the gold triangle is on the bottom-left

corner of the socket. Fit the socket alignment

key into the CPU notch.

Gold

triangle

mark

Alignment key

6. Close the load plate (A), then push the load

lever (B) until it snaps into the retention tab.

A

B

Installing an AMD CPU

1. Locate the CPU socket, then lift the socket lever to a 90º angle.

2. Install the CPU to the socket, making sure that the CPU corner with the gold

triangle matches the socket corner with a small triangle.

3. Push down the socket lever to secure the CPU.

1 2 3

CAUTION: Incorrect installation of the CPU into the socket may bend the pins and

severely damage the CPU!

Installing the CPU fan and heatsink assembly

®

®

Installing an Intel

Pentium

4 CPU heatsink and fan

1. Place the heatsink on top of the installed

CPU, making sure that the four fasteners

A

match the holes on the motherboard.

B

2. Push down two fasteners at a time in a

B

diagonal sequence to secure the heatsink

and fan assembly in place.

A

3. When the fan and heatsink assembly is in

place, connect the CPU fan cable to the

connector on the motherboard.

1

1

Installing an AMD CPU heatsink and fan

1. Place the heatsink on top of the installed CPU.

IMPORTANT.Makesurethatthefanandheatsinkassemblyperfectlytstheretention

mechanism module base; otherwise you can not lock the retention bracket.

2. Attach one end of the retention bracket to the retention module base.

3. Attach the other end of the retention bracket (near the retention bracket lock)

to the retention module base until it clicks in place.

NOTE. Your boxed CPU should come with installation instructions for the CPU, fan/heatsink

assembly, and the retention mechanism. If the instructions in this section do not match the

CPU documentation, follow the latter.

4. Push down the retention bracket lock on the retention mechanism to secure

the fan and heatsink to the module retention module base.

5. Connect the CPU fan cable to the connector on the motherboard.

CAUTION. Do not forget to connect the CPU fan connector! Hardware monitoring error

can occur if you fail to plug this connector.

1

2

CPU fan

Retention

bracket lock

5

4

CPU fan

connector

Retention bracket

CPU heatsink

3

Retention module base

Installing a DIMM

1. Locate the DIMM sockets in the motherboard.

2. Unlock a DIMM socket by pressing the retaining clips outward.

3. Align a DIMM on the socket such that the notch on the DIMM matches the

break on the socket.

4. Push the DIMM to the socket until the retaining clips snap inward.

CAUTION:

• Unplug the power supply before adding or removing DIMMs. Failure to do so may

cause damage to the motherboard and/or components.

 • ADDRDIMMiskeyedwithanotchsothatittsinonlyonedirection.Donotforce

a DIMM into a socket to avoid damaging the DIMM.

Installing an expansion card

2. Remove the metal bracket lock.1. Remove the metal cover opposite

the slot that you intend to use.

1

2

3

3. Insert the card connector to the

slot,thenpressthecardrmly

untilittsinplace.

4. Replace the metal bracket lock.

4

Installing storage drives

Optical drive

1. Place the chassis upright, then

remove the upper 5.25” drive bay

2

metal plate cover.

2. Insert the optical drive to the bay,

3

3

then carefully push the drive until its

screw holes align with the holes on

the bay.

3. Secure the optical drive with two

screws on both sides of the bay.

4. Connect the IDE (A) and power (B)

plugs to connectors at the back of

the drive.

B

A

Floppy disk drive

1. Place the chassis upright, then

remove the lower 3.5” drive bay

metal plate cover.

3

2. Inserttheoppydiskdrivetothe

bay, then carefully push the drive

until its screw holes align with the

2

3

holes on the bay.

3. Securetheoppydiskdrivewith

two screws on both sides of the

bay.

B

4. Connect the signal (A) and power

(B) plugs to connectors at the back

of the drive.

A

Hard disk drive

1. Place the chassis upright, then

remove the upper 3.5” drive bay

metal plate cover.

2. Insert the hard disk drive to the bay,

3

then carefully push the drive until its

screw holes align with the holes on

3

the bay.

2

3. Secure the hard disk drive with two

screws on both sides of the bay.