Asus P2-P5945GCX: инструкция

English

P1-P5945G/P2-P5945G

ASUS PC (Desktop Barebone)

Installation Manual

Download the latest manual from the ASUS website: www.asus.com

Front panel features

Close

Optical drive eject

button

HDD LED

Optical drive bay

cover

Press to open the

front panel cover

Power button

Power LED

Front panel features

Rear panel features

Open

Power connector

Voltage selector*

Reset button

Center/Sub out

MS/MS Pro card slot

Rear Surround L/R

Side Surround L/R

Line In

®

CompactFlash

card

Line Out

slot

Rear MIC

SD/MMC card slot

PS/2 mouse port

PS/2 keyboard port

LAN (RJ-45) port

USB 2.0 ports

4-pin IEEE 1394 port

SPDIF Out port

USB 2.0 ports

VGA port

Headphone port

DVI-D port

Microphone port

Serial port

PCI slot metal brackets

* The system’s power supply unit has a

115 V/230 V voltage selector switch located near the power connector. Use this switch

to select the correct system input voltage according to the voltage supply in your area.

Internal components

3

1

2

5

4

8

7

6

1. 5.25-inch optical drive and

5. ASUS motherboard

3.5 inch hard disk drive cage

6. DIMM sockets

2. Front panel cover

7. LGA775 socket

(under the CPU

3. Power supply unit

fan and heatsink assembly)

4. PCI card riser bracket

8. CPU fan and heatsink assembly

(connected to the

motherboard PCI slot)

Removing the cover

1. Remove the cover screws. Keep the screws for later use.

2. Pull the cover slightly toward the rear panel.

3. Lift the cover, then set aside.

1

32

Removing the front panel cover

1. Lift the front panel cover

1 2

hooks outward.

2. Carefully remove the front

panel cover, then set it aside.

Removing the storage drive assembly

1. Lay the system on its side,

2. Lift the storage drive assembly,

then locate and remove three

then set aside.

storage drive assembly screws.

Removing the CPU fan and heatsink

1. Disconnect the CPU fan cable.

3. Lift the CPU fan and heatsink

assembly, then set aside.

2. Loosen the CPU fan and

heatsink assembly screws.

Installing the CPU

1. Unlock the load lever, then lift

2. Lift the load plate, then

to a 90º-100º angle.

remove the PnP cap.

Load leverRetention tab

3. Install the CPU. The CPU ts in

4. Close the load plate, then lock

only one orientation.

the load lever.

5. Reinstall the CPU fan and heatsink assembly, then reconnect the CPU

fan cable to the CPU fan connector on the motherboard. Refer to the

instructions in the previous section for details.

Installing a DIMM

1. Locate the DIMM sockets in the

Unlocked

motherboard.

retaining clip

2. Unlock a DIMM socket by

pressing the retaining clips

outward.

3. Align a DIMM on the socket

such that the notch on the

DIMM matches the break on the

socket.

DDR DIMM notch

Installing an expansion card

1. Lift the PCI riser card assembly

2. Remove the metal cover

to remove.

opposite the slot that you

intend to use.

3. Insert the card connector to

4. Reinstall the PCI riser card

the slot, then press the card

assembly. Make sure that the

rmly until it ts in place.

riser card connector sits properly

Secure the card with a screw.

on the motherboard PCI slot.

Installing optical and storage drives

1. Turn the storage drive assembly upside down with the 3.5-inch bay on

top of the 5.25-inch bay.

2. Insert the optical drive upside down to the 5.25-inch bay, then secure

it with two screws on both sides.

3. Turn the storage drive assembly, insert the hard disk drive upside down to

the 3.5-inch bay, then secure it with two screws on both sides.

2

3

Reinstalling the storage drive assembly

Before reinstalling the storage drive assembly, connect the IDE/SATA and

power plugs to the IDE/SATA and power connectors at the back of the

drives.

1. Connect the black plug of the IDE cable to the optical drive, then the

gray plug to the hard disk drive. If you have the SATA HDD, connect

the SATA cable to the SATA HD.

2. Connect the 4-pin power plugs to the power connectors at the back

of the drives.

3. Install the storage drive assembly to the chassis.

4. Secure the storage drive assembly with three screws.

3

4

Installing the foot stand

1. Match the foot stand hooks to

2. Pull the foot stand to the

the holes on the chassis.

direction of the arrow until the

lock clicks in place.

To remove the foot stand, lift the lock, then slightly push the foot stand to

the direction of the rear panel until it disengages from the chassis.

Reinstalling the front panel cover

English

1. Insert the front panel cover

1 2

tabs to the holes at the right

side of the chassis, then close.

2. Insert the front panel cover

hooks to the chassis tabs until

the front panel cover ts in

place.

Reinstalling the cover

1. Install the cover to the chassis. Make sure the cover tabs t the chassis rails.

2. Push the cover toward the front panel until it ts in place.

3. Secure the cover with two screws.

1

2

3

8 Installation manual