Yamaha CD-S300 Black: CONTROLS AND FUNCTIONS

INTRODUCTION

CONTROLS AND FUNCTIONS

Front panel

1 (Power)

Note

Press to turn the power on/off.

Connect using the ANALOG OUT terminals when you use

y

PURE DIRECT mode (refer to page 3).

• The power indicator above lights up when this unit is turned on.

• Playback starts automatically if the power is turned on while a

7 Disc tray

disc is set in the disc tray.

Loads a disc.

2 Power indicator

8 (Open/Close)

Lights up as follows:

Opens or closes the disc tray.

ON: Bright

OFF: Off

9 Remote control sensor

Receives signals from the remote control.

3 iPod/USB port

Connect your iPod or USB device. See page 6 for details.

0 / (Skip/Search backward),

/ (Skip/Search forward)

4 iPod/USB indicator

/ : Skips to the next track.

Off: CD mode is selected.

/ : Skips back to the beginning of the current

Orange: Connection ready.

track.

Green: iPod/USB is connected and playable files have

/ (twice): Skips to the previous track.

been detected (playback ready).

Press and hold / or / to search

5 CD/USB

backward/forward.

Swithes between CD mode and iPod/USB mode (see

A (Play)

page 6).

Starts playback.

y

B (Pause)

When the iPod/USB indicator is not lit, this unit is in the CD

mode.

Pauses playback. Press or to resume playback.

6 PURE DIRECT

C (Stop)

Turns on or off the PURE DIRECT mode to improve

Stops playback.

audio quality.

y

• The PURE DIRECT indicator lights up.

• The digital output is turned off.

• The front panel display is turned off during playback and only

the minimum required indicators and messages are displayed

during in the operation.

2 En

CONTROLS AND FUNCTIONS

INTRODUCTION

D Playback Status Indicator

G Advanced setup indicator

Lights up when this unit is in the play or pause mode.

Indicates the enabled special modes. See “USING THE

ADVANCED SETUP” (page 9) for details.

E Source type indicator

Indicates the type of content being played back.

H Multi-information display

F Time and playback mode indicator

Indicates the current playback mode and the status of the

time display (see pages 5 and 5 for playback modes, and

page 5 for time display).

Rear panel connections

CAUTION

Before making any connection, switch OFF the power to the unit, the amplifier and any other component.

Audio cable (supplied)

Optical digital cable

cable

Coaxial digital

Connect the supplied power cable into

the AC IN inlet on the rear panel when

all connections are complete, and then

plug in the power cable to the AC outlet.

The audio signals are only output from the ANALOG OUT jacks

when the PURE DIRECT mode is on.

Amplifier

■ VOLTAGE SELECTOR

Voltages are as follows:

(Asia and General models only)

...............AC 110/120/220/230-240 V, 50/60 Hz

CAUTION

The VOLTAGE SELECTOR on the rear panel of this unit

230-

must be set for your local voltage BEFORE plugging the

Voltage indication

240V

power cable into the AC wall outlet. Improper setting of

the VOLTAGE SELECTOR may cause damage to this

VO LTAGE

SELECTOR

unit and create a potential fire hazard.

English

Rotate the VOLTAGE SELECTOR clockwise or

counterclockwise to the correct position using a straight

slot screwdriver.

3 En

CONTROLS AND FUNCTIONS

Remote control

■ Installing batteries in the remote control

1 Press the part and slide the battery

compartment cover off.

2 Insert the two supplied batteries (AA, R6,

UM-3) according to the polarity markings (+

and –) on the inside of the battery

compartment.

3 Slide the cover back until it snaps into place.

■ Using the remote control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the front panel of this unit during

operation.

Within 6 m

(20 ft)

1 Infrared signal transmitter

y

This setting is retained even if you turn off this unit.

Sends infrared signals to this unit.

5 Numeric buttons

2 CD/USB

Use to select directly a track on the disc or a file in the

Switches between CD mode and iPod/USB mode (see

current folder.

page 6).

y

6 (Search backward), (Search

This setting is retained even if you turn off this unit.

forward)

Searches tracks backward/forward while the key is

3 PROGRAM

pressed.

Turns on or off the program playback mode. See

“Program playback” on the next page.

7 (Skip backward), (Skip forward)

: Skips to the next track.

4 DIMMER

: Skips back to the beginning of the current track.

Each time you press DIMMER, the brightness level

(twice): Skips to the previous track.

changes by 4 levels.

4 En

CONTROLS AND FUNCTIONS

8 FOLDER (Folder down), (Folder up)

D A/B

Audio CD

Data Disc USB

Repeats playback of a specified section of a track. To set

: Skips to the previous folder.

the starting and end points (A and B), press A/B twice

: Skips to the next folder.

during playback.

INTRODUCTION

Refer to page 6 for details.

To cancel repeat A-B, press A/B again.

9 OPEN/CLOSE

Notes

Opens or closes the disc tray.

• You cannot set repeat A-B from one track to another track.

0 PURE DIRECT

• You cannot set repeat A-B for Data Disc and USB.

• If you stop playback by pressing (Stop), repeat A-B is canceled.

Turns on or off the PURE DIRECT mode to improve

• You cannot use repeat A-B when this unit is in the PURE

audio quality. See page 2 for details.

DIRECT mode.

y

E CLEAR

This setting is retained even if you turn off this unit.

Erases the programmed track.

A RANDOM

F ENTER

Turns on or off the random sequence playback mode.

Confirms a track number entered when you are

Note

programming tracks.

The random playback mode is canceled when the disc is ejected.

G (Pause)

B REPEAT

Pauses playback. Press or to resume playback.

Repeats playback of a single track or all tracks. Each time

H (Play)

you press REPEAT during playback, the repeat playback

Starts playback.

mode changes as follows:

• REP TRACK (single repeat playback): A single track

See pages 8 for more information on MP3/WMA

is played back repeatedly.

playback.

• REP ALL (all repeat playback): All tracks (the entire

disc) are played back repeatedly.

I (Stop)

Data Disc USB

Stops playback.

• REP FOLDER (folder repeat playback): All files (the

entire folder) are played back repeatedly.

Program playback

Audio CD

y

In the program playback mode, you can play back tracks

Repeat play also works with program play and random-sequence

in a programmed sequence.

play.

C DISPLAY

1 Press PROGRAM while playback is stopped.

Switches the time display. Each time you press DISPLAY

This unit is set to the program editing mode.

during playback, the time display changes as follows:

Audio CD

2 Select a track by using the numeric buttons

and ENTER.

Elapsed time of the current

Album name

track (default)

3 Repeat step 2 to program the next track.

Remaining time of the current

Artist name

You can program up to 24 tracks.

track

y

To cancel the programmed track, press CLEAR.

Total remaining time of the

Track name

disc

4 Press .

(CD TEXT disc only)

Playback starts from the beginning of the

Data Disc USB

programmed sequence.

Elapsed time of the current

Album name

y

file (default)

To erase all programmed tracks, press CLEAR when the

playback is stopped.

Artist name

English

Note

The programmed tracks are erased when the disc is ejected or this

unit is turned off.

Title

(Files including tag

information only)

5 En