Главная > Инструкция к Автомагнитоле JVC KD-SC607 > RADIO OPERATIONS

JVC KD-SC607: RADIO OPERATIONS

RADIO OPERATIONS: JVC KD-SC607

RADIO OPERATIONS

ENGLISH

To stop searching before a station is

Listening to the radio

received, press the same button you have

pressed for searching.

You can use either automatic searching or manual

searching to tune in to a particular station.

Note:

FM1 and FM2: 87.5 MHz – 108.0 MHz

Searching for a station automatically:

FM3: 65.00 MHz – 74.00 MHz

Auto search

1

Select the band (FM1 – 3, AM).

Searching for a station manually:

Each time you press the

Manual search

button, the band changes as

follows:

1

Select the band (FM1 – 3, AM).

FM1 FM2 FM3 AM

Each time you press the

button, the band changes as

follows:

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

FM1 FM2 FM3 AM

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

Selected band appears.

an FM broadcast.

Note:

2

Press and hold ¢ or 4

This receiver has three FM bands (FM1, FM2,

until “M” (manual) starts flashing on

FM3). You can use any one of them to listen to

the display.

an FM broadcast.

2

Start searching for a station.

To search for stations

of higher frequencies

To search for stations of lower frequencies

When a station is received, searching stops.

10

EN10-12_KD-SC607[EE]f.p65 11/27/03, 12:17 PM10

3

Tune in to a station you want while

Storing stations in memory

“M” (manual) is still flashing.

You can use one of the following two methods to

To tune in to stations of

store broadcasting stations in memory.

higher frequencies

• Automatic preset of FM stations: SSM (Strong-

ENGLISH

station Sequential Memory)

• Manual preset of both FM and AM stations

To tune in to stations of lower frequencies

FM station automatic preset: SSM

• If you release your finger from the button,

You can preset 6 local FM stations in each FM

the manual mode will automatically turns

band (FM1, FM2, and FM3).

off after 5 seconds.

• If you hold down the button, the frequency

1

Select the FM band (FM1 – 3) you

keeps changing—in 50 kHz intervals

want to store FM stations into.

(87.5 MHz – 108.0 MHz for FM 1 and

FM 2), in 30 kHz intervals (65.00 MHz –

Each time you press the

74.00 MHz for FM 3) and 9 kHz for AM

button, the band changes as

—MW/LW until you release the button.

follows:

FM1 FM2 FM3 AM

When an FM stereo broadcast is hard to

receive:

1 Press M MODE to enter the

2

Press M MODE to enter the

functions mode while listening

functions mode.

to an FM stereo broadcast.

2 Press MO (monaural), while

“MODE” is still flashing on the

display, so that “MONO”

3

Press and hold SSM for about

appears on the display.

2 seconds.

Each time you press the button,

monaural mode turns on and off

alternately.

MO (monaural) indicator

“SSM” flashes, then disappears when

automatic preset is over.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

Local FM stations with the strongest signals are

reception will be improved.

searched and stored automatically in the band

number you have selected (FM1, FM2, or FM3).

These stations are preset in the number buttons

—No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

11

EN10-12_KD-SC607[EE]f.p65 11/27/03, 12:17 PM11

Manual preset

4

Repeat the above procedure to store

You can preset up to 6 stations in each band

other stations into other preset

(FM1, FM2, FM3, and AM) manually.

numbers.

ENGLISH

Ex.: Storing FM station of 92.5 MHz into the

Notes:

preset number 1 of the FM1 band.

• A previously preset station is erased when a new

station is stored in the same preset number.

1

Select the band (FM1 – 3, AM) you

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example,

want to store stations into (in this

during battery replacement). If this occurs, preset

example, FM1).

the stations again.

Each time you press the

button, the band changes as

follows:

Tuning in to a preset station

FM1 FM2 FM3 AM

You can easily tune in to a preset station.

Remember that you must store stations first. If

you have not stored them yet, see “Storing

2

Tune in to a station (in this example,

stations in memory” on pages 11 and 12.

of 92.5 MHz).

To tune in to stations of

1

Select the band (FM1 – 3, AM).

higher frequencies

Each time you press the

button, the band changes as

follows:

To tune in to stations of lower frequencies

FM1 FM2 FM3 AM

2

Select the number (1 – 6) for the

preset station you want.

3

Press and hold the number button

(in this example, 1) for more than

2 seconds.

Note:

You can also use the 5 (up) or ∞ (down) button on

the unit to select the next or previous preset stations.

Each time you press the 5 (up) or ∞ (down) button,

the next or previous preset station is tuned in.

Preset number flashes for a while.

12

EN10-12_KD-SC607[EE]f.p65 11/27/03, 12:17 PM12

Оглавление

Топ 10 инструкций

Другие инструкции

JVC KD-S711R JVC KD-S711R JVC KD-S847 JVC KD-S847 JVC KD-SC800R JVC KD-SC800R JVC KD-SH707R JVC KD-SH707R Siemens WIQ1432EU Siemens WIQ1432EU LG F1058ND LG F1058ND